Thread Tools Display Modes
  #1   Report Post  
Mark
 
Posts: n/a
Default NAD 7100 - will not power up

I have a 1991 NAD 7100 receiver that I left on this morning when I left
for work in order to tape something. There were severe thunderstorms
this afternoon during which the power went out at least once and now the
7100 will not power up. It gets AC power through a Monster HT-1000 and
the other components seem to be fine.

This has happened before, but the condition was always corrected by
unplugging the power cord then plugging it back in. That would reset
something, as the receiver is in a 'ready' state anytime it is plugged
in.

I removed the cover and all of the fuses seem to be fine. The front
panel microswitch seems to be fine. The unswitched back panel AC outlet
has power, otherwise, the receiver is dead.

Questions:

Is there something obvious I'm overlooking?

Should just I be happy about 12 years of faithful service from a $630.00
receiver and go shopping?

Thanks in advance!

--
Mark R. Ransom
Raleigh, North CArolina USA
  #2   Report Post  
GregS
 
Posts: n/a
Default NAD 7100 - will not power up

In article , Mark wrote:
I have a 1991 NAD 7100 receiver that I left on this morning when I left
for work in order to tape something. There were severe thunderstorms
this afternoon during which the power went out at least once and now the
7100 will not power up. It gets AC power through a Monster HT-1000 and
the other components seem to be fine.


Some of these NAD's have microprocessor turn on circuits. Some are not available anymore.
Maybe try collecting insurance??

greg
  #3   Report Post  
Mark
 
Posts: n/a
Default NAD 7100 - will not power up

Greg: This model is like that; the green power switch on the front
panel activates a microswitch mounted on a PC board.

Tim: I removed the cover and looked at that fuse. It is on a vertical
pc board at the back, under a zip-tied black flap - you have a great
recollection of the layout! That fuse has a really thin wire with a
small sphere in the middle. It does not look blown, but I want to put
in a similar fuse to be certain.

I believe that there is a transformer mounted on the left side of the
chassis, just in front of a larger component that appears to be a power
supply. It looks a little discolored and has a glob of hardened clear
substance on it, but from what little I know about electronic
components, it appears to be OK.

Since you are in the business, do you think repair is worth persuing?
Considering; 12 years old, original cost of $630, probable $80-100 bench
fee to look at it, availability of replacement parts ...

Thank you very much for your time.



In article ,
Tim Schwartz wrote:

Mark,

Did you check the 5A "T" mains fuse near the rear panel? As I recall
it is hidden underneath a black plastic cover, and you might have to cut
a cable-tie to get to it, or it might be on the bottom of the unit, its
been a while since I've seen one of these. If this fuse is blown it
will likely blow again at turn on, as something else is wrong with the
amp. I've also seen power transformers open on some NAD amps, but don't
remember if its this model.

Regards,
Tim Schwartz
Bristol Electronics


Mark wrote:

I have a 1991 NAD 7100 receiver that I left on this morning when I left
for work in order to tape something. There were severe thunderstorms
this afternoon during which the power went out at least once and now the
7100 will not power up. It gets AC power through a Monster HT-1000 and
the other components seem to be fine.

This has happened before, but the condition was always corrected by
unplugging the power cord then plugging it back in. That would reset
something, as the receiver is in a 'ready' state anytime it is plugged
in.

I removed the cover and all of the fuses seem to be fine. The front
panel microswitch seems to be fine. The unswitched back panel AC outlet
has power, otherwise, the receiver is dead.

Questions:

Is there something obvious I'm overlooking?

Should just I be happy about 12 years of faithful service from a $630.00
receiver and go shopping?

Thanks in advance!

--
Mark R. Ransom
Raleigh, North CArolina USA


--
Mark
Raleigh, North Carolina
  #4   Report Post  
steve grinstead
 
Posts: n/a
Default NAD 7100 - will not power up

GO SHOPPING
"Mark" wrote in message
...
I have a 1991 NAD 7100 receiver that I left on this morning when I left
for work in order to tape something. There were severe thunderstorms
this afternoon during which the power went out at least once and now the
7100 will not power up. It gets AC power through a Monster HT-1000 and
the other components seem to be fine.

This has happened before, but the condition was always corrected by
unplugging the power cord then plugging it back in. That would reset
something, as the receiver is in a 'ready' state anytime it is plugged
in.

I removed the cover and all of the fuses seem to be fine. The front
panel microswitch seems to be fine. The unswitched back panel AC outlet
has power, otherwise, the receiver is dead.

Questions:

Is there something obvious I'm overlooking?

Should just I be happy about 12 years of faithful service from a $630.00
receiver and go shopping?

Thanks in advance!

--
Mark R. Ransom
Raleigh, North CArolina USA





----== Posted via Newsfeed.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeed.com The #1 Newsgroup Service in the World! 100,000 Newsgroups
---= 19 East/West-Coast Specialized Servers - Total Privacy via Encryption =---
 
Thread Tools
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
help! need Tandberg or Revox power cord CRD General 0 July 3rd 03 02:45 PM


All times are GMT +1. The time now is 12:02 AM.

Powered by: vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AudioBanter.com.
The comments are property of their posters.
 

About Us

"It's about Audio and hi-fi"