Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Multi Media Wiring
I am designing several churches.
Can you give me a generic spec for the following wiring? [I don't mean a specific brand, just a designation, like "CAT-5" and "RJ-45" for network wiring, etc] 1.. From Microphone jacks at pulpit to sound board 1.. cable: 2.. connector: 3.. box recessed into pulpit [brand name/# ?] 2.. From Sound Board to amplifier 1.. cable 2.. connector 3.. From Amplifier to Speaker Jack 1.. cable 2.. connector 4.. From Video Projector to PC at sound board 1.. cable 2.. connector Thanks!!! -- Steve Brown email: website: www.dai2.com |
#2
|
|||
|
|||
Multi Media Wiring
"Steve" wrote in message
I am designing several churches. Can you give me a generic spec for the following wiring? [I don't mean a specific brand, just a designation, like "CAT-5" and "RJ-45" for network wiring, etc] From Microphone jacks at pulpit to sound board cable: 2-conductor shielded audio cable connector: XLR or TRS as appropriate box recessed into pulpit [brand name/# ?] From Sound Board to amplifier cable: 2-conductor shielded audio cable connector: XLR or TRS as appropriate From Amplifier to Speaker Jack cable: 12-16 gauge low voltage connector: 1/4" mono phone or SpeakOn as appropriate From Video Projector to PC at sound board cable connector Depends on the input video projector, but if it has a 15 pin RGB input, then one uses RGB extension cables such as are used with KVM switches. |
#3
|
|||
|
|||
Multi Media Wiring
In article , "Steve"
writes: Can you give me a generic spec for the following wiring? [I don't mean = a specific brand, just a designation, like "CAT-5" and "RJ-45" for = network wiring, etc] Here are my suggestions, realizing that I work for Belden, a cable manufacturer. (The non-cable suggestions are mine personally and not the opinion of Belden corporately.) 1.. From Microphone jacks at pulpit to sound board 1.. cable: 2.. connector: I would use Belden 1800F. This is ultralow capacitance (13pF/ft.) for maximum performance but is very flexible and comes in a variety of colors. (I would guess you will want black so it is not obvious.) My peronal favorite connectors are the Neutrik NC3FX-B and MX-B but any XLR connector (Switchcraft A3F/A3M, ITT Canon etc.) will work just fine. 3.. box recessed into pulpit [brand name/# ?] I assume you mean the mic cable goes into a box which then transitions to an install-grade cable from there to the mixer. I would use Belden 1800B which has the same performance as the 1800F but much lower price and is install-only. If you have multiple microphone, we also make this in multipair snake up to 32 pair. 2.. From Sound Board to amplifier 1.. cable 2.. connector=20 Question: is the output of the mixer balanced (XLR) or unbalanced (RCA/mono phone plug)? BALANCED: 1800B and XLRs as above. UNBALANCED: Belden 1505A and Canare RCA connectors. (Note that I am recommending a competitors!!! connectors, so they must be pretty good.) If it's phone plug, I would have to think about whose plug (check Neutrik or Canare). 3.. From Amplifier to Speaker Jack I assume you are using the direct out (i.e. 8 ohms etc.) and this is not a 70-volt distributed system. If you have long speaker runs, more than 100 ft., I would suggest an amplifier with 70-v output and transformer-fed speakers. If you don't know what this means, email me and I will explain further. 1.. cable 2.. connector 8 ohm output: Belden 8477 (12 AWG). If you want REALLY low loss, we have the only UL-recognized 10 AWG speaker cable (Belden 5T00UP), yes a weird part number for us. Check this (and all these cables) out at www.belden.com This assumes standard amp and speaker terminals. If you have Neutrik Speakon outputs at the amp and Speakons at the speaker, we do make that cable too: Belden 1810A (4 X 14 AWG) Belden 1811A (8X14 AWG) 4.. From Video Projector to PC at sound board 1.. cable 2.. connector A previous post said it. Is this VGA, like a laptop? High-density 15-pin connector? Or RGB? (probably not). What distance are you going? You can get premade VGA cables for cheap. If they are not long enough or the picture looks like crap, and you want to make your own cables...let's talk. (Making VGA cables is NOT FUN.) Thanks!!! --=20 Steve Brown Hope this helps. Steve Lampen Belden Electronics Division |