Reply
 
Thread Tools Display Modes
  #1   Report Post  
 
Posts: n/a
Default

"Phil Allison" wrote:
|
| The pilot and subcarrier add to the total deviation, thus forcing a slight
| reduction of the main signal's deviation.
|
|
|** But that has no effect on " Tx range ".

A reduction in main signal level causes a like increase in SNR.
Therefore, for a given SNR, this effectively reduces the "TX range"

Phil
  #2   Report Post  
Phil Allison
 
Posts: n/a
Default



"Phil Allison"
|
| The pilot and subcarrier add to the total deviation, thus forcing a
slight
| reduction of the main signal's deviation.
|
|
|** But that has no effect on " Tx range ".

A reduction in main signal level causes a like increase in SNR.



** The noise level at the receiver depends only on the *carrier's signal
strength* at its location and then only when it has fallen below a certain
( very low) threshold.

Therefore, for a given SNR, this effectively reduces the "TX range"



** Nonsense.



......... Phil








  #3   Report Post  
 
Posts: n/a
Default

"Phil Allison" wrote:

|

| "Phil Allison"
| |
| | The pilot and subcarrier add to the total deviation, thus forcing a slight
| | reduction of the main signal's deviation.
| |
| |** But that has no effect on " Tx range ".
|
| A reduction in main signal level causes a like increase in SNR.
|
|
|** The noise level at the receiver depends only on the *carrier's signal
|strength* at its location and then only when it has fallen below a certain
|( very low) threshold.

The noise level in relation to total carrier modulation "only depends
on Carrier's signal strength", but when L+R only gets a (major)
portion of the total modulation, the ratio between that L+R and noise
goes down.

Lets set up a receiver/meter such that a 400 cps sine 100% modulating
the transmitter (with no stereo) produces 1.0 volts on the receiver
output. Now turn on the pilot and feedn the 400 cps to L and R. 100%
modulation of the transmitter will require a 1 db reduction of the 400
cps to leave room for the pilot, and the output from the receiver will
be reduced 1 db, However, the noise in the receiver output will be
unchanged, so if we had 70 db snr in mono, we now have 69 db remaining
SNR (if the stereo garbage doesn't decrease it further).

| Therefore, for a given SNR, this effectively reduces the "TX range"
|
|
|** Nonsense.

In order to maintain a 70 db SNR, you would have to have a stronger
signal, perhaps achieved by moving closer to the transmitter. (or
buying a better receiver or a better antenna).

Phil
Reply
Thread Tools
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Not In Love With Tivoli Audio? Maybe Here is Why-FAQ and Exegesis [email protected] Audio Opinions 5 April 25th 05 01:35 AM
Opinions Needed on New DIY Radio Site DIYer Tech 2 January 11th 05 02:15 AM
USING INTERNET RADIO TO MARKET YOUR MUSIC By Mark W. Curran Mark W. Curran Pro Audio 2 May 16th 04 12:30 AM
FS:Tube/radio manuals, books. Mark Oppat Marketplace 0 January 26th 04 05:06 AM
FS: misc books... Mark Oppat Marketplace 0 January 7th 04 07:04 AM


All times are GMT +1. The time now is 10:18 AM.

Powered by: vBulletin
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AudioBanter.com.
The comments are property of their posters.
 

About Us

"It's about Audio and hi-fi"