Hello,

I'm at a point in my home studio where I need a bunch
of 2 foot 1/4" patch cords, and a few long balanced ones
as well. I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap. Please advise.

"james of tucson" wrote ...
I'm at a point in my home studio where I need a bunch
of 2 foot 1/4" patch cords, and a few long balanced ones
as well. I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap. Please advise.

The connectors you are pricing are likely significantly
higher quality than those used in the manufactured cables
you are comparing to. Note that they are also repairable
where molded-connector cables are almost "throwaways".

"Richard Crowley" wrote in message
...
"james of tucson" wrote ...
I'm at a point in my home studio where I need a bunch
of 2 foot 1/4" patch cords, and a few long balanced ones
as well. I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap. Please advise.

The connectors you are pricing are likely significantly
higher quality than those used in the manufactured cables
you are comparing to. Note that they are also repairable
where molded-connector cables are almost "throwaways".

not necessarily better quality.
major manufacturers are going to get a very large bulk discount on their
connectors.
they are also going to have better equipment for building the cables which
will make their staff more efficient such as automatic wire strippers
tinning machines and all kinds of things that just make them more efficient.

the biggest thing is the buying power.
I cant buy my stock for anywhere near the price that a large cable
manufacturer can.

Doug

james of tucson wrote:

I'm at a point in my home studio where I need a bunch
of 2 foot 1/4" patch cords, and a few long balanced ones
as well. I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap. Please advise.

If you want long-frame stuff, the premade cables are definitely the way
to go. I like the Neutrik ones, with nice metal ends that are easily
repaired. Soldering long-frame plugs is a pain and Neutrik can do it
cheaply enough.

Avoid cables with molded connectors like the plague. All cables will
fail, but if they have connectors you can unscrew, you can fix them when
they do. If they have molded connectors, you throw them away.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

On 2004-11-06, Scott Dorsey wrote:

Avoid cables with molded connectors like the plague.

Thanks for the reply, Scott.
I haven't skimped on instrument cables. I'm a keyboard player with
7 main instruments in my rig, so that's 7 stereo channels, plus 8 submix
channels coming out of one of my synths, plus spdif in one case.
Anyway from the instrument to the patchbay and/or recorder I use nice
expensive cables of correct length and all is good. But now I'm trying
to do more with effects and so forth in my rack, and a pedalboard, &c,
and so I'm suddenly in need of about a jillion 2-foot-or-less cables.

I'm very good at making stuff, but alas, the strategy of DIY is no
bargain here.

Hello,

I'm at a point in my home studio where I need a bunch
of 2 foot 1/4" patch cords, and a few long balanced ones
as well. I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap. Please advise.


DIY are gonna be a better grade patch cord for the same dollars, about $8.
AP Audio makes 2' packaged 8 for $24.00.
Here's a link. They're all priced about the same. I've had better luck with
the AP Audio in molded cables.

http://www.zzounds.com/cat--AP-Audio--2924

YMMV

--Wayne

-"sounded good to me"-

On 2004-11-06, Wayne wrote:

DIY are gonna be a better grade patch cord for the same dollars, about $8.
AP Audio makes 2' packaged 8 for $24.00.

The one review on Zzounds says they are crap. So the question is one of
degree of crappyness. Is Hosa also crap? Better or worse?

I didn't really consider the cost of cables in the budget. I'm looking
at a couple hundered just for cheap ass cables.

Thanks!

james of tucson wrote:
On 2004-11-06, Wayne wrote:

DIY are gonna be a better grade patch cord for the same dollars, about $8.
AP Audio makes 2' packaged 8 for $24.00.

The one review on Zzounds says they are crap. So the question is one of
degree of crappyness. Is Hosa also crap? Better or worse?

HOSA doesn't even _make_ long-frame patch cords as far as I know, and the
cables they do make, I wouldn't wish on my worst enemy.

I didn't really consider the cost of cables in the budget. I'm looking
at a couple hundered just for cheap ass cables.

And then a couple hundred more to replace them when they fail, plus lost time.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

On 2004-11-08, Scott Dorsey wrote:

And then a couple hundred more to replace them when they fail, plus lost time.

Right, a lesson I don't need to learn, and the reason I'm trying to
avoid it. I *know* I make better stuff than they, "they" being anyone
else, but the barrier to entry (1000' of mic cable, a bin of connectors)
has me sticker shocked. For the cost of cabling, I could buy another
instrument, or an effects box or a mic or something :-)

james of tucson wrote:
On 2004-11-08, Scott Dorsey wrote:
And then a couple hundred more to replace them when they fail, plus lost time.

Right, a lesson I don't need to learn, and the reason I'm trying to
avoid it. I *know* I make better stuff than they, "they" being anyone
else, but the barrier to entry (1000' of mic cable, a bin of connectors)
has me sticker shocked. For the cost of cabling, I could buy another
instrument, or an effects box or a mic or something :-)

Right. Mike cables aren't exciting. But they are things that you need
to have and there's really no way around that. Sadly, most of the really
important things in the studio (like room acoustics) wind up in that category.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

"james of tucson" wrote:

[...] the barrier to entry (1000' of mic cable, a bin of connectors)
has me sticker shocked. For the cost of cabling, I could buy
another instrument, or an effects box or a mic or something :-)



If it helps any, you're not alone. Seems lots of people make wiring an
afterthought and don't budget for cable.

I'm building a little overdub/post room in my house. I already have
whatever equipment I need, so the costs have just been minor
renovations, fixtures/millwork, acoustic treatments and interconnects.
Since the rooms are small and there isn't much gear involved, I figured
the budget would be credit card small. Whoops.

Looking at just wiring (since that's all that's relevant to this
discussion):

- four 48 point patchbays, which I bought used really cheap. Since I'm
only ever moving eight channels or so at a time, this was enough for
mixer interconnects and a small assortment of outboard (a more
complicated rig would require many more points). $300

- a ten foot line from each patchbay jack to a corresponding point on a
piece of gear in the rack or the mixer. Doesn't sound like very much
wire until you do the math -- 48 x 4, x ten feet each. Almost half a
mile of wire just for a simple little rig! I had planned to use name
brand cable (I've always used Mogami in the past) but this time opted
for generic simply based on price. Two boxes of 1000 feet each was
$200. Double that for name-brand.

- connectors for the "other" end of those ten foot lines. Fortunately I
know a connector wholesaler so I was able to get Switchcraft and Neutrik
at a substantial discount, but enough 1/4"-TRS and XLR connectors to do
the job still came out to roughly $750.

With other miscellaneous materials and supplies, the cost of wiring a
*very* basic rig with generic cable, used patchbays and discounted
connectors was close to $1500. Something for everyone to consider when
budgeting for system upgrades.

--
"It CAN'T be too loud... some of the red lights aren't even on yet!"
- Lorin David Schultz
in the control room
making even bad news sound good

(Remove spamblock to reply)

In article y.com writes:

I didn't really consider the cost of cables in the budget. I'm looking
at a couple hundered just for cheap ass cables.

Many people don't think about cables when buying gear. It can easiliy
cost $1,000 for cables to hook up a basic 24-track system. When faced
with a project like that, it makes more sense to set aside a week and
make all your own cables - the right length, with the right
connectors, the right number in a bundle, labels on both ends. When
you need a handful of cables, like to go between jacks on your
patchbay, it makes more sense to buy them ready-made.

Some people call every cable a "patch cable" which makes answering
generic questions difficult.

--
I'm really Mike Rivers )
However, until the spam goes away or Hell freezes over,
lots of IP addresses are blocked from this system. If
you e-mail me and it bounces, use your secret decoder ring
and reach me he double-m-eleven-double-zero at yahoo

On Sat, 06 Nov 2004 21:11:50 GMT, james of tucson
wrote:

I'm at a point in my home studio where I need a bunch
of 2 foot 1/4" patch cords, and a few long balanced ones
as well. I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap. Please advise.


Home-made will be better quality, and repairable. Or you can buy a
bunch of cheapo ready-mades and treat them as disposable. They work
OK until they fail :-)

CubaseFAQ www.laurencepayne.co.uk/CubaseFAQ.htm
"Possibly the world's least impressive web site": George Perfect

In article y.com writes:

I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap.

No, you can use good connectors, good cable, and good assembly
techniques and end up with a better cable than you can buy cheap.

But welcome to the world of mass production. Companies like Hosa use
connectors that have fewer metal parts (in fact fewer parts, period)
than the connectors that you can buy to assemble yourself, and they
use a lot of automated tooling to assemble the cables. Also, they buy
parts by the truckload. So they can buy parts at lower cost than you
can, they can assemble them more efficiently, and they may even use
parts that you can't buy on the retail market.

My advice is not to try to save money on cables that you can buy
conveniently. Make the custom cables that you can't buy off the shelf.
Those are the ones that will cost you a lot if you have to pay someone
to custom build them for you.


--
I'm really Mike Rivers )
However, until the spam goes away or Hell freezes over,
lots of IP addresses are blocked from this system. If
you e-mail me and it bounces, use your secret decoder ring
and reach me he double-m-eleven-double-zero at yahoo

james of tucson wrote in message vatory.com...
Hello,

I'm at a point in my home studio where I need a bunch
of 2 foot 1/4" patch cords, and a few long balanced ones
as well. I'm good at making things, but I've found the
cost of the connectors at the best prices I can find, to
be as high as manufactured cables. In order for DIY to
be effective, the parts have to be cheap. Please advise.


Conquest sells some nice premade cables. I have 20 4ft unbalanced
cables from them that I have beat the crap out of and they are still
going strong. They are soft and flex nicely when patched into a
vertical surface.

For DIY check out Redco online. They have some good deals on
connectors and cables. They have been fast and friendly. On one
occasion where a part was out of stock they offered a slightly more
expensive version as a replacement at no extra cost. The difference
didn't add up to much costwise for them; however when a business does
that for me they usually will make it back up in future sales.
The prices beat electronics catalog prices by a longshot.



I usually buy cable from Gepco. They are near my house and make a
good product. I had a chance to take a mini tour around the factory.
It's very clean and well organized. They have a quality room there and
are ISO (I forget the number) certified. The unbalanced cable I have
from them is stiffer than the Conquest cable. I prefer this for
patching into horizontal surfaces because the cables go up and out of
the way of the patching surface. I save on shipping by picking it up
in person.

I'm sure there are many opinions on cable flexability.


The cable is probably the heaviest part of your order. Check to see
if there is a company near you that sells cable. Maybe there is a PA
rental place near you that will go in on an order. This will split
shipping and could bring you up to the next price break level.

On 2004-11-07, Peter B. wrote:

Thank you, Peter. There's a lot of good advice in your post.
I envision a corner of my office with a 1000' spool of mic cable
and a parts bin full of connectors, and I think you just got me
there.