Ham-Fisted AT T-341 Mic Battery cover! >:(

[[email protected]]

SOMEBODY at our church, apparently of super-human strength,
managed to over tighten the battery cover on the above mic
such that no one is able to reopen it!


My feeble attempts usually result in unscrewing the opposite end -
the pick-up module. It's been sitting in our office like that for 3
weeks now, and I'm just afraid of what is happening to the
rechargeable batteries in there. Will It one day be opened, with
tons of white powdery battery innards falling out?


Just need suggestions on how to unscrew the battery
compartment.

[geoff]

On 2/08/2016 11:21 a.m., wrote:
> SOMEBODY at our church, apparently of super-human strength,
> managed to over tighten the battery cover on the above mic
> such that no one is able to reopen it!
>
>
> My feeble attempts usually result in unscrewing the opposite end -
> the pick-up module. It's been sitting in our office like that for 3
> weeks now, and I'm just afraid of what is happening to the
> rechargeable batteries in there. Will It one day be opened, with
> tons of white powdery battery innards falling out?
>
>
> Just need suggestions on how to unscrew the battery
> compartment.

Prayer should do it.

geoff

[geoff]

On 2/08/2016 11:24 a.m., geoff wrote:
> On 2/08/2016 11:21 a.m., wrote:
>> SOMEBODY at our church, apparently of super-human strength,
>> managed to over tighten the battery cover on the above mic
>> such that no one is able to reopen it!
>>
>>
>> My feeble attempts usually result in unscrewing the opposite end -
>> the pick-up module. It's been sitting in our office like that for 3
>> weeks now, and I'm just afraid of what is happening to the
>> rechargeable batteries in there. Will It one day be opened, with
>> tons of white powdery battery innards falling out?
>>
>>
>> Just need suggestions on how to unscrew the battery
>> compartment.
>
> Prayer should do it.
>
> geoff

Or you could try gently warming the cover end with a hot-air gun.
Carefully.

I guess the body not strong enough to grab with big-jawed pliers wrapped
in cloth....

geoff

[Scott Dorsey]

> wrote:
>
>Just need suggestions on how to unscrew the battery
>compartment.

Put it in the freezer.

You can also try using a small amount of a thin machine oil.
--scott

--
"C'est un Nagra. C'est suisse, et tres, tres precis."

[Frank Stearns]

(Scott Dorsey) writes:

> > wrote:
>>
>>Just need suggestions on how to unscrew the battery
>>compartment.

>Put it in the freezer.

Yes, cold is a better idea than heating, as heating is going to make things larger
and thus lock the threads together even more. Cold will cause all the dimensions
to shrink a wee bit, hopefully breaking that lock you have currently.

My only question about the freezer would be any risk to the diaphragm... (dunno,
just asking). I'd assume a factory-new diaphragm should be able to handle such cold,
no problem... But if there's any residual moisture in any internal nooks and
crannies perhaps that could set things up for a crack.

As a precaution before freezing the mic, I'd be inclinded to air-tight bag it in
uncooked raw white rice for a day to wick out any residual moisture. Are you in a
humid climate? If so that would be an even stronger motive to "dry the mic" prior to
a freeze.

>You can also try using a small amount of a thin machine oil.

Another good idea; underscore "small amount".

I wouldn't worry much about the batteries until a year or two has gone by. :)

Frank
Mobile Audio

--

[Tobiah]

On 08/01/2016 04:21 PM, wrote:
> SOMEBODY at our church, apparently of super-human strength,
> managed to over tighten the battery cover on the above mic
> such that no one is able to reopen it!
>
>
> My feeble attempts usually result in unscrewing the opposite end -
> the pick-up module. It's been sitting in our office like that for 3
> weeks now, and I'm just afraid of what is happening to the
> rechargeable batteries in there. Will It one day be opened, with
> tons of white powdery battery innards falling out?

The first thing that comes to mind is to wrap both parts in some
pieces of old bicycle inner-tube and apply some force with a couple
of sets of slip-lock pliers. You'd get tons of grip while minimizing
damage.

[Scott Dorsey]

In article >, Tobiah > wrote:
>On 08/01/2016 04:21 PM, wrote:
>> SOMEBODY at our church, apparently of super-human strength,
>> managed to over tighten the battery cover on the above mic
>> such that no one is able to reopen it!
>>
>>
>> My feeble attempts usually result in unscrewing the opposite end -
>> the pick-up module. It's been sitting in our office like that for 3
>> weeks now, and I'm just afraid of what is happening to the
>> rechargeable batteries in there. Will It one day be opened, with
>> tons of white powdery battery innards falling out?
>
>The first thing that comes to mind is to wrap both parts in some
>pieces of old bicycle inner-tube and apply some force with a couple
>of sets of slip-lock pliers. You'd get tons of grip while minimizing
>damage.

If you HAVE to force it, use strap wrenches (make a pair if your hardware
store doesn't have them). But really, try hard not to force it.
--scott

--
"C'est un Nagra. C'est suisse, et tres, tres precis."

[John Williamson]

On 02/08/2016 15:14, Scott Dorsey wrote:
> In article >, Tobiah > wrote:
>> On 08/01/2016 04:21 PM, wrote:
>>> SOMEBODY at our church, apparently of super-human strength,
>>> managed to over tighten the battery cover on the above mic
>>> such that no one is able to reopen it!
>>>
>>>
>>> My feeble attempts usually result in unscrewing the opposite end -
>>> the pick-up module. It's been sitting in our office like that for 3
>>> weeks now, and I'm just afraid of what is happening to the
>>> rechargeable batteries in there. Will It one day be opened, with
>>> tons of white powdery battery innards falling out?
>>
>> The first thing that comes to mind is to wrap both parts in some
>> pieces of old bicycle inner-tube and apply some force with a couple
>> of sets of slip-lock pliers. You'd get tons of grip while minimizing
>> damage.
>
> If you HAVE to force it, use strap wrenches (make a pair if your hardware
> store doesn't have them). But really, try hard not to force it.
> --scott
>
Just a thought. You can buy aids for disabled people to help them undo
things like soda bottle tops, in a range of sizes, one of which should
fit the mic body. A couple of these will give a *lot* more leverage than
hands alone, and as they are rubber lined for a good grip on wet things,
they won't damage the finish.

--
Tciao for Now!

John.

[[email protected]]

Frank Stearns wrote: "My only question about the freezer would be any risk to the diaphragm... (dunno, "


Since, as I indicated, the pickup section still unscrews, I can remove it,
and put the battery half in a bag and in the freezer for a half hour. Then
try unscrewing it.

[[email protected]]

Frank Stearns wrote: "I wouldn't worry much about the batteries until a year or
two has gone by. :) "


I've had some of the AAs in a dozen room wall clocks
shed crusty residue in less than 6 months after
changing - good old Energizer or Duracells, no
cheapo brands.

[JackA]

On Tuesday, August 2, 2016 at 2:21:17 PM UTC-4, wrote:
> Frank Stearns wrote: "My only question about the freezer would be any risk to the diaphragm... (dunno, "
>
>
> Since, as I indicated, the pickup section still unscrews, I can remove it,
> and put the battery half in a bag and in the freezer for a half hour. Then
> try unscrewing it.

As John mentioned, you should use a rubber thing before screwing!!

Jack :)

[[email protected]]

JackA:

Can you be serious for five minutes? Seconds?

[JackA]

On Tuesday, August 2, 2016 at 3:14:32 PM UTC-4, wrote:
> JackA:
>
> Can you be serious for five minutes? Seconds?

Yeah, you and your 3kHz serious stuff.

Jack

[geoff]

On 3/08/2016 1:35 AM, Frank Stearns wrote:
> (Scott Dorsey) writes:
>
>> > wrote:
>>>
>>> Just need suggestions on how to unscrew the battery
>>> compartment.
>
>> Put it in the freezer.
>
> Yes, cold is a better idea than heating, as heating is going to make things larger
> and thus lock the threads together even more. Cold will cause all the dimensions
> to shrink a wee bit, hopefully breaking that lock you have currently.

All the dimensions (both body and battery caps) shrink, so tightness may
remain the same. Difficult to chill just one section.

Warming ( OK not 'heating') just the battery cover end has always worked
for me without complications.

geoff

[[email protected]]

geoff wrote: "Warming ( OK not 'heating') just the battery cover end has always worked
for me without complications. "

Thanks. If I go the warming route, a hair dryer it is!

[Scott Dorsey]

geoff > wrote:
>All the dimensions (both body and battery caps) shrink, so tightness may
>remain the same. Difficult to chill just one section.

Correct. But the body and cap shrinks and then when you take it out and put
your warm hand on the cap, it warms back up very quickly and expands and
everything comes apart.

Try it! I have done this more than once!

>Warming ( OK not 'heating') just the battery cover end has always worked
>for me without complications.

It likely would too. Harder to do in a controlled way though.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

[JackA]

On Tuesday, August 2, 2016 at 3:58:56 PM UTC-4, geoff wrote:
> On 3/08/2016 1:35 AM, Frank Stearns wrote:
> > (Scott Dorsey) writes:
> >
> >> > wrote:
> >>>
> >>> Just need suggestions on how to unscrew the battery
> >>> compartment.
> >
> >> Put it in the freezer.
> >
> > Yes, cold is a better idea than heating, as heating is going to make things larger
> > and thus lock the threads together even more. Cold will cause all the dimensions
> > to shrink a wee bit, hopefully breaking that lock you have currently.
>
> All the dimensions (both body and battery caps) shrink, so tightness may
> remain the same. Difficult to chill just one section.
>
> Warming ( OK not 'heating') just the battery cover end has always worked
> for me without complications.

[joke] Hope the batteries don't explode. But, hey, at lease the cover will blow off! :)

Jack
>
> geoff

[Phil Allison[_4_]]

Frank Stearns wrote:

>
>
> >Put it in the freezer.
>
> Yes, cold is a better idea than heating, as heating is going to make
> things larger and thus lock the threads together even more. Cold will
> cause all the dimensions to shrink a wee bit, hopefully breaking that
> lock you have currently.
>
>

** That is faulty reasoning.

When you heat a metal part with a hole in it - the hole expands. Conversely cooling the same part makes the hole smaller.

This is why heating a frozen-on nut works to loosen it.

When the materials are the same, the aim is to achieve a difference in temperature, so that the hole expands while the object inside the hole does not.

Some may be familiar with ball bearings that are heat fitted into alloy housings - steel expands less than aluminium so simply heating both makes the previously tight fit come loose.


..... Phil

[Trevor]

On 3/08/2016 12:33 AM, John Williamson wrote:
> On 02/08/2016 15:14, Scott Dorsey wrote:
>> In article >, Tobiah >
>> wrote:
>>> On 08/01/2016 04:21 PM, wrote:
>>>> SOMEBODY at our church, apparently of super-human strength,
>>>> managed to over tighten the battery cover on the above mic
>>>> such that no one is able to reopen it!
>>>>
>>>>
>>>> My feeble attempts usually result in unscrewing the opposite end -
>>>> the pick-up module. It's been sitting in our office like that for 3
>>>> weeks now, and I'm just afraid of what is happening to the
>>>> rechargeable batteries in there. Will It one day be opened, with
>>>> tons of white powdery battery innards falling out?
>>>
>>> The first thing that comes to mind is to wrap both parts in some
>>> pieces of old bicycle inner-tube and apply some force with a couple
>>> of sets of slip-lock pliers. You'd get tons of grip while minimizing
>>> damage.
>>
>> If you HAVE to force it, use strap wrenches (make a pair if your hardware
>> store doesn't have them). But really, try hard not to force it.
>> --scott
>>
> Just a thought. You can buy aids for disabled people to help them undo
> things like soda bottle tops, in a range of sizes, one of which should
> fit the mic body. A couple of these will give a *lot* more leverage than
> hands alone, and as they are rubber lined for a good grip on wet things,
> they won't damage the finish.


A similar trick is to simply wear a pair of rubber gloves, you'll be
amazed how much more grip you get than bare hands. Spray on a little
WD40 or penetrene etc. to the joint first, and you probably won't need
heat or cold or tools.

Trevor.

[JackA]

On Wednesday, August 3, 2016 at 12:22:36 AM UTC-4, Phil Allison wrote:
> Frank Stearns wrote:
>
> >
> >
> > >Put it in the freezer.
> >
> > Yes, cold is a better idea than heating, as heating is going to make
> > things larger and thus lock the threads together even more. Cold will
> > cause all the dimensions to shrink a wee bit, hopefully breaking that
> > lock you have currently.
> >
> >
>
> ** That is faulty reasoning.
>
> When you heat a metal part with a hole in it - the hole expands. Conversely cooling the same part makes the hole smaller.
>
> This is why heating a frozen-on nut works to loosen it.
>
> When the materials are the same, the aim is to achieve a difference in temperature, so that the hole expands while the object inside the hole does not.
>
> Some may be familiar with ball bearings that are heat fitted into alloy housings - steel expands less than aluminium so simply heating both makes the previously tight fit come loose.
>
>
> .... Phil

The coefficient of thermal expansion, along with rapid oxidation, is the cause of house fires when aluminum wiring was first used.

Jack

[Don Pearce[_3_]]

On Tue, 2 Aug 2016 21:22:32 -0700 (PDT), Phil Allison
> wrote:

>Frank Stearns wrote:
>
>>
>>
>> >Put it in the freezer.
>>
>> Yes, cold is a better idea than heating, as heating is going to make
>> things larger and thus lock the threads together even more. Cold will
>> cause all the dimensions to shrink a wee bit, hopefully breaking that
>> lock you have currently.
>>
>>
>
>** That is faulty reasoning.
>
>When you heat a metal part with a hole in it - the hole expands. Conversely cooling the same part makes the hole smaller.
>
>This is why heating a frozen-on nut works to loosen it.
>
>When the materials are the same, the aim is to achieve a difference in temperature, so that the hole expands while the object inside the hole does not.
>
>Some may be familiar with ball bearings that are heat fitted into alloy housings - steel expands less than aluminium so simply heating both makes the previously tight fit come loose.
>
>
>.... Phil
>

When the two parts are locked tightly together it is hard to get any
differential heating - they both get hot together. As the hole expands
at exactly the same rate as the metal, things don't get loose. What
does happen is that the oxide layer gluing them together gets
disrupted, and with a bit of tapping and nudging, things can often be
persuaded to come apart.

d

---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

[Gareth Magennis[_3_]]

wrote in message
...

SOMEBODY at our church, apparently of super-human strength,
managed to over tighten the battery cover on the above mic
such that no one is able to reopen it!


My feeble attempts usually result in unscrewing the opposite end -
the pick-up module. It's been sitting in our office like that for 3
weeks now, and I'm just afraid of what is happening to the
rechargeable batteries in there. Will It one day be opened, with
tons of white powdery battery innards falling out?


Just need suggestions on how to unscrew the battery
compartment.






Wrap some rubber (elastic) bands around the mic body and battery cover, and
try by hand again.


Gareth.

[[email protected]]

12:47 PMgareth magennis wrote:

"Wrap some rubber (elastic) bands around the mic body and battery cover, and
try by hand again. "

I tried the same thing about, with a pair of rubber oven
mitts, thing still wouldn't budge. I think it's toast.

Sad - and stupid - even for a church.


Gareth.

[[email protected]]

12:47 PMgareth magennis wrote:

"Wrap some rubber (elastic) bands around the mic body and battery cover, and
try by hand again. "

I tried the same thing about, with a pair of rubber oven
mitts, thing still wouldn't budge. I think it's toast.

Sad - and stupid - even for a church.


Gareth.

[Gareth Magennis[_3_]]

wrote in message
...

12:47 PMgareth magennis wrote:

"Wrap some rubber (elastic) bands around the mic body and battery cover,
and
try by hand again. "

I tried the same thing about, with a pair of rubber oven
mitts, thing still wouldn't budge. I think it's toast.

Sad - and stupid - even for a church.









Two pairs of Mole Grips then, and try and minimise damage with some kind of
padding of their teeth.
(Not rubber bands, the teeth bite right through them)


AND, I would try and impact drive them somehow, rather than just twist.
Hold one firm and whack the other with something heavy. This might break
the bond.




Gareth.



Gareth.

[John Williamson]

On 07/08/2016 20:13, Gareth Magennis wrote:
>
>
> wrote in message
> ...
>
> 12:47 PMgareth magennis wrote:
>

> I tried the same thing about, with a pair of rubber oven
> mitts, thing still wouldn't budge. I think it's toast.
>
> Sad - and stupid - even for a church.
>
As a last resort, send it to a maker's service agent or other audio gear
repair shop, and if they damage the case, they should be able to buy a
replacement from the makers or will have the parts in stock, so won't be
paranoid about damage to the casing. It might even be cheaper than
buying a good quality used replacement.



--
Tciao for Now!

John.

[JackA]

On Sunday, August 7, 2016 at 2:03:18 PM UTC-4, wrote:
> 12:47 PMgareth magennis wrote:
>
> "Wrap some rubber (elastic) bands around the mic body and battery cover, and
> try by hand again. "
>
> I tried the same thing about, with a pair of rubber oven
> mitts, thing still wouldn't budge. I think it's toast.
>
> Sad - and stupid - even for a church.

Have you tried an 18" pipe wrench?

Jack :)
>
>
> Gareth.

[Gareth Magennis[_3_]]

"Scott Dorsey" wrote in message ...

In article >, Tobiah > wrote:
>On 08/01/2016 04:21 PM, wrote:
>> SOMEBODY at our church, apparently of super-human strength,
>> managed to over tighten the battery cover on the above mic
>> such that no one is able to reopen it!
>>
>>
>> My feeble attempts usually result in unscrewing the opposite end -
>> the pick-up module. It's been sitting in our office like that for 3
>> weeks now, and I'm just afraid of what is happening to the
>> rechargeable batteries in there. Will It one day be opened, with
>> tons of white powdery battery innards falling out?
>
>The first thing that comes to mind is to wrap both parts in some
>pieces of old bicycle inner-tube and apply some force with a couple
>of sets of slip-lock pliers. You'd get tons of grip while minimizing
>damage.

If you HAVE to force it, use strap wrenches (make a pair if your hardware
store doesn't have them). But really, try hard not to force it.
--scott

--





The method required here is an impact technique to break the bond, not
steady force, which will break the mic.


Gareth.

[Scott Dorsey]

Gareth Magennis > wrote:
>
>The method required here is an impact technique to break the bond, not
>steady force, which will break the mic.

I'd believe that if it were galled aluminum or rusted steel, but it's
cheap thermoplastic.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

[Gareth Magennis[_3_]]

"Scott Dorsey" wrote in message ...

Gareth Magennis > wrote:
>
>The method required here is an impact technique to break the bond, not
>steady force, which will break the mic.

I'd believe that if it were galled aluminum or rusted steel, but it's
cheap thermoplastic.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."





Whenever I come across something like this I can't solve, I take it to my
work neighbour, a Ukrainian motor mechanic.
He can't always help, but sometimes has the knowledge/experience and tools
to do so, these people can be quite resourceful.

He brings me dead car ECU's occasionally. I've managed to fix a couple of
those without any car to test it with.
Works both ways.



Gareth.

[[email protected]]

gareth magennis wrote: "Whenever I come across something like this I
can't solve, I take it to my work neighbour, a"


All I want to solve is WHO closed this thing so
tight. You figure if they were strong enough to
overtighten it, they're strong enough to unscrew
it.

[Gareth Magennis[_3_]]

wrote in message
...

gareth magennis wrote: "Whenever I come across something like this I
can't solve, I take it to my work neighbour, a"


All I want to solve is WHO closed this thing so
tight. You figure if they were strong enough to
overtighten it, they're strong enough to unscrew
it.





The threads may have been corroded/contaminated with sweat or something
else.


Gareth

[[email protected]]

John Williamson wrote: "a last resort, send it to a maker's service agent or other audio gear
repair shop, and if they damage the case, they should be able to buy a
replacement from the makers or will have the parts in stock, so won't be
paranoid about damage to the casing. It might even be cheaper than
buying a good quality used replacement. "


We are a very small, spiritually rich but financially
poor church. The last thing our pastor would want
to spend money on is the battery compartment of
a wireless mic. Besides, we have other wireless
and hard-wire options for that position.

This was an exceptionally nice AT at the time it was
purchased, but I think the best thing to do will be to
just replace it - and be CAREFUL next time! >:/

[[email protected]]

Pastor brought it up to me again, says he wants to bring mic to local Sam Ash where he bought it to see if they could dislodge battery cover. I told him, they'll charge you at least $25 just to look at it. Pastor replied with a smile: "This mic plus receiver cost nearly $700 brand new. Do you think $25-30 is that big a deal to get use of this microphone back"?

[Mike Rivers[_2_]]

On 8/14/2016 8:59 PM, wrote:
> Pastor brought it up to me again, says he wants to bring mic to local
> Sam Ash where he bought it to see if they could dislodge battery
> cover. I told him, they'll charge you at least $25 just to look at
> it.

Really? Probably a ham-fisted drummer at the store will grab it and open
it right up. No charge. Might be better to send it to Audio Technica,
though.

> Pastor replied with a smile: "This mic plus receiver cost nearly
> $700 brand new. Do you think $25-30 is that big a deal to get use of
> this microphone back"?

This is a person you could learn something from about the cost of doing
business. Or can you show him that he can get a new one that's better
and costs $100.

--

For a good time, call http://mikeriversaudio.wordpress.com

[[email protected]]

On Monday, August 15, 2016 at 6:49:53 AM UTC-4, Mike Rivers wrote:
>
> Really? Probably a ham-fisted drummer at the store will grab it and open
> it right up. No charge. Might be better to send it to Audio Technica,
> though."

Probably what he will end up doing - sending it
to the mfg.



> > Pastor replied with a smile: "This mic plus receiver cost nearly
> > $700 brand new. Do you think $25-30 is that big a deal to get use of
> > this microphone back"?
>
Or can you show him that he can get a new one that's better
> and costs $100."

What do you mean by that?

[Mike Rivers[_2_]]

On 8/15/2016 7:45 AM, wrote:

>>> Pastor replied with a smile: "This mic plus receiver cost nearly
>>> $700 brand new. Do you think $25-30 is that big a deal to get use of
>>> this microphone back"?

> Or can you show him that he can get a new one that's better
>> and costs $100."

> What do you mean by that?

I mean that he had a valid question and you apparently don't have a good
answer. Obviously he still wants a wireless mic and is willing to pay a
reasonable amount to have it repaired if he hasn't found someone (you?)
to fix it for free. You haven't come up with an alternative that's more
cost effective than a repair.





--

For a good time, call http://mikeriversaudio.wordpress.com

[Scott Dorsey]

> wrote:
>Pastor brought it up to me again, says he wants to bring mic to local Sam A=
>sh where he bought it to see if they could dislodge battery cover. I told =
>him, they'll charge you at least $25 just to look at it. Pastor replied wi=
>th a smile: "This mic plus receiver cost nearly $700 brand new. Do you thi=
>nk $25-30 is that big a deal to get use of this microphone back"?

So, do it. They'll put it in the freezer.
I think $25 for a bench fee is incredibly cheap, I'd definitely take it.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

[Trevor]

On 15/08/2016 11:17 PM, Scott Dorsey wrote:
> > wrote:
>> Pastor brought it up to me again, says he wants to bring mic to local Sam A=
>> sh where he bought it to see if they could dislodge battery cover. I told =
>> him, they'll charge you at least $25 just to look at it. Pastor replied wi=
>> th a smile: "This mic plus receiver cost nearly $700 brand new. Do you thi=
>> nk $25-30 is that big a deal to get use of this microphone back"?
>

> I think $25 for a bench fee is incredibly cheap, I'd definitely take it.

You do realise he said "at least $25 just to look at it", and that was
just a guess anyway I bet.

Trevor.

[[email protected]]

Trevor wrote: "do realise he said "at least $25 just to look at it", and that was
just a guess anyway I bet. "


A reasonable guess. Might even be $50 bench. The
question is how much Pastor is willing to pay. As some
here might have missed out on, I did mention this is
not the only wireless mic we have in the church. Just
miles away the most expensive one!

[geoff]

On 16/08/2016 10:37 PM, wrote:
> Trevor wrote: "do realise he said "at least $25 just to look at it", and that was
> just a guess anyway I bet. "
>
>
> A reasonable guess. Might even be $50 bench. The
> question is how much Pastor is willing to pay. As some
> here might have missed out on, I did mention this is
> not the only wireless mic we have in the church. Just
> miles away the most expensive one!
>


Shouldn't you be able to simply pray it off ?

geoff

[JackA]

On Tuesday, August 16, 2016 at 6:53:26 AM UTC-4, geoff wrote:
> On 16/08/2016 10:37 PM, wrote:
> > Trevor wrote: "do realise he said "at least $25 just to look at it", and that was
> > just a guess anyway I bet. "
> >
> >
> > A reasonable guess. Might even be $50 bench. The
> > question is how much Pastor is willing to pay. As some
> > here might have missed out on, I did mention this is
> > not the only wireless mic we have in the church. Just
> > miles away the most expensive one!
> >
>
>
> Shouldn't you be able to simply pray it off ?

I enjoy cleverness! Pry - Pray!

Jack
>
> geoff

[Tobiah]

On 08/16/2016 03:53 AM, geoff wrote:
> On 16/08/2016 10:37 PM, wrote:
>> Trevor wrote: "do realise he said "at least $25 just to look at it", and that was
>> just a guess anyway I bet. "
>>
>>
>> A reasonable guess. Might even be $50 bench. The
>> question is how much Pastor is willing to pay. As some
>> here might have missed out on, I did mention this is
>> not the only wireless mic we have in the church. Just
>> miles away the most expensive one!
>>
>
>
> Shouldn't you be able to simply pray it off ?

They can't hold the thing steady enough - they got rid of vices
a long time ago.

[JackA]

On Tuesday, August 16, 2016 at 1:06:52 PM UTC-4, Tobiah wrote:
> On 08/16/2016 03:53 AM, geoff wrote:
> > On 16/08/2016 10:37 PM, wrote:
> >> Trevor wrote: "do realise he said "at least $25 just to look at it", and that was
> >> just a guess anyway I bet. "
> >>
> >>
> >> A reasonable guess. Might even be $50 bench. The
> >> question is how much Pastor is willing to pay. As some
> >> here might have missed out on, I did mention this is
> >> not the only wireless mic we have in the church. Just
> >> miles away the most expensive one!
> >>
> >
> >
> > Shouldn't you be able to simply pray it off ?
>
> They can't hold the thing steady enough - they got rid of vices
> a long time ago.

They got rid of the vice squad? No wonder why a lot of foul play!

Jack

[Mike Rivers[_2_]]

On 8/16/2016 2:31 PM, JackA wrote:

> They got rid of the vice squad? No wonder why a lot of foul play!

Now you're just playing chicken.

Oh, and the thing that holds stuff is spelled VISE.


--

For a good time, call http://mikeriversaudio.wordpress.com

[JackA]

On Tuesday, August 16, 2016 at 2:47:19 PM UTC-4, Mike Rivers wrote:
> On 8/16/2016 2:31 PM, JackA wrote:
>
> > They got rid of the vice squad? No wonder why a lot of foul play!
>
> Now you're just playing chicken.
>
> Oh, and the thing that holds stuff is spelled VISE.

Excuse me, my dear Mike....

"A vise or vice is a mechanical apparatus used to secure an object to allow work to be performed on it. Vises have two parallel jaws, one fixed and the other movable, threaded in and out by a screw and lever".

Thank you. Now we both learned something new!

Jack
>
>
> --
>
> For a good time, call http://mikeriversaudio.wordpress.com

[[email protected]]

On Monday, August 1, 2016 at 7:22:10 Pl.com wrote:
> SOMEBODY at our church, apparently of super-human strength,
> managed to over tighten the battery cover on the above mic
> such that no one is able to reopen it!
>
>
> My feeble attempts usually result in unscrewing the opposite end -
> the pick-up module. It's been sitting in our office like that for 3
> weeks now, and I'm just afraid of what is happening to the
> rechargeable batteries in there. Will It one day be opened, with
> tons of white powdery battery innards falling out?
>
>
> Just need suggestions on how to unscrew the battery
> compartment.



GOT IT!!!


I put the battery end of the mic in the vise, surrounded by a thick rubber lid opener. I used another lid opener, and after 3 minutes of straining, it snapped open.

Batteries had not swollen or burst, and innards were clean. Still powers up after all this time, but definitely rechargeables need a charging, only 1 of 5 dots showing. My friend theorized the batteries had burst inside, and had swollen the cover shut. But they and microphone are all good.

Thanks all! Pastor will be sighing relieve, and his daughter will have her favorite worship mic back.


AMEN! And to all the non-believers, God Bless You!

[JackA]

On Sunday, August 21, 2016 at 2:39:53 PM UTC-4, wrote:
> On Monday, August 1, 2016 at 7:22:10 Pl.com wrote:
> > SOMEBODY at our church, apparently of super-human strength,
> > managed to over tighten the battery cover on the above mic
> > such that no one is able to reopen it!
> >
> >
> > My feeble attempts usually result in unscrewing the opposite end -
> > the pick-up module. It's been sitting in our office like that for 3
> > weeks now, and I'm just afraid of what is happening to the
> > rechargeable batteries in there. Will It one day be opened, with
> > tons of white powdery battery innards falling out?
> >
> >
> > Just need suggestions on how to unscrew the battery
> > compartment.
>
>
>
> GOT IT!!!
>
>
> I put the battery end of the mic in the vise, surrounded by a thick rubber lid opener. I used another lid opener, and after 3 minutes of straining, it snapped open.

Must have had your Wheaties today!

Jack
>
> Batteries had not swollen or burst, and innards were clean. Still powers up after all this time, but definitely rechargeables need a charging, only 1 of 5 dots showing. My friend theorized the batteries had burst inside, and had swollen the cover shut. But they and microphone are all good.
>
> Thanks all! Pastor will be sighing relieve, and his daughter will have her favorite worship mic back.
>
>
> AMEN! And to all the non-believers, God Bless You!