Home |
Search |
Today's Posts |
#1
Posted to rec.audio.pro
|
|||
|
|||
Sennheiser G2 wiring question
I have a Sennheiser evolution G2 SK100 transmitter and I need some wiring
help. I've searched the SennUSA site but can't find out how to wire a Senn MKE2-5 mic for this xmitter. This is a pigtail version of the mic and the jack on the SK100 accepts a 3.5mm stereo plug. The wires coming out of the pigtail are red, blue, braided copper and two silver-looking wires which I assume are for strain relief. Any help with this? |
#2
Posted to rec.audio.pro
|
|||
|
|||
Sennheiser G2 wiring question
In article ,
Dave Morrison wrote: I have a Sennheiser evolution G2 SK100 transmitter and I need some wiring help. I've searched the SennUSA site but can't find out how to wire a Senn MKE2-5 mic for this xmitter. This is a pigtail version of the mic and the jack on the SK100 accepts a 3.5mm stereo plug. The wires coming out of the pigtail are red, blue, braided copper and two silver-looking wires which I assume are for strain relief. Any help with this? The silver wires are almost certainly the shield if they are wrapped around the outside. They go to the sleeve. Now which wire goes to tip and which to ring? You can use a diode tester function on the DMM to check the microphone and the voltmeter to see what the polarity of the supply in the pack is. Or you could just use clip leads and try both combinations. One will work, one will not. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#3
Posted to rec.audio.pro
|
|||
|
|||
Sennheiser G2 wiring question
Scott,
The silver wires (there are two of them) are tightly wound and almost feel like stainless steel. If they are the shield, what function would the copper braided wire serve? dave "Scott Dorsey" wrote in message ... In article , Dave Morrison wrote: I have a Sennheiser evolution G2 SK100 transmitter and I need some wiring help. I've searched the SennUSA site but can't find out how to wire a Senn MKE2-5 mic for this xmitter. This is a pigtail version of the mic and the jack on the SK100 accepts a 3.5mm stereo plug. The wires coming out of the pigtail are red, blue, braided copper and two silver-looking wires which I assume are for strain relief. Any help with this? The silver wires are almost certainly the shield if they are wrapped around the outside. They go to the sleeve. Now which wire goes to tip and which to ring? You can use a diode tester function on the DMM to check the microphone and the voltmeter to see what the polarity of the supply in the pack is. Or you could just use clip leads and try both combinations. One will work, one will not. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#4
Posted to rec.audio.pro
|
|||
|
|||
Sennheiser G2 wiring question
Dave Morrison wrote:
Scott, The silver wires (there are two of them) are tightly wound and almost feel like stainless steel. If they are the shield, what function would the copper braided wire serve? The outer braid is also a shield. The stainless stuff is probably for stiffness only, but it won't hurt to connect it to the shield. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#5
|
|||
|
|||
Quote:
Hello Dave, The Sennheiser G2 Body pack uses the 3.5mm input for Mic and Line level independently on different pins / TIP and RING. TIP and SHIELD are used for Microphone input,,,,, RING and SHIED are for LINE. For Condenser Mic Connection onto 3.5mm male Connector.: 1st determine the microphones Hot wire, (Generally Red family shades), and, solder to 3.5mm TIP. 2nd, solder remaining wire(s) to SHIELD. SHIELD serves as NEGATIVE/GROUND and also carry's 48V Phantom Power . For Line Level input: ONLY using a three wire balanced connector. (use adapters to unbalance) Solder the HOT wire to the 3.5mm connectors RING, tie GROUND and SHIELD together and solder to the 3.5mm connectors SHIELD. Though there are some variables, this is pretty much standard for Countryman, Sennheiser, Sony and Sure Condenser lavalier Microphones. ALSO, Your microphones RED is the HOT, Blue is Negative. the third is shield and strain relief. This wire is made of Tungsten and cannot be soldered. To make the false positive connection that works: a) Sand the tungsten wire solder area with a nail filer. B) Wrap a few strands of bare copper wire evenly around the tungsten and tin. Last edited by Salvatore Marino : June 8th 11 at 08:33 PM Reason: additional information |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Sennheiser MD 402-U - general question | Pro Audio | |||
sennheiser way to go with nature recordings: Sennheiser MKH-40 pair or Sennheiser MKH-30 + MKH-40 combo? | Pro Audio | |||
sennheiser headphone wiring | Tech | |||
Sennheiser 825S Wiring? | Pro Audio | |||
Sennheiser MD-21 Question | Pro Audio |