Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Help selecting bench power supply ?
I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? Thanks! Joe |
#2
|
|||
|
|||
Joe wrote:
I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? Thanks! Joe Try finding an old Heathkit supply. I picked up an IP-32 for a few bucks that does exactly what you need, 0-400v with filament and even a negative 0-150 bias supply. That or hang around your university. Mine tossed some old rackmount Lamda supplies that work fine. Or you could always get a small variac and 120-240 step up transformer with a diode bridge. Make sure whatever you use is isolated from the line. I used a setup like that before getting a real supply. Adam |
#3
|
|||
|
|||
I have an old tube power supply, bench type. It's a beauty, supplying lots
of 6.3 V and up to 500V DC and variable bias, I think the main output is good to a few hundred milliamperes. Two big meters. On a rack panel, heavy as the dickens. I don't use this thing and would like someone to make me an offer. I also have a smaller one on a little chassis that isn't variable or regulated. That I would sell cheaper, or even trade for something. Bob in Los Angeles |
#4
|
|||
|
|||
On Fri, 05 Nov 2004 00:15:41 +0000, Joe wrote:
I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? I've used a Radford N15R power pack for preamp stages & similar low current stuff. Quite a few of these have been disposed of by schools over the years - they were originally used for the physics course before people decided that things like x-ray tubes were too dangerous for us kids! Get a smalli variac and use it to drive the primary of a reasonable mains tranny for the HT. Ignore the heater windings on this. This should be independently switched. SS rectifier & suitable caps rated for the full output (fit bleeder resistors and a voltmeter). Use second and possible third heater trannys, not fed via the variac. Also a seperate bias supply using a ww pot and giving up to say 100v should be ok for a lot of stuff. -- Mick (no M$ software on here... :-) ) Web: http://www.nascom.info |
#5
|
|||
|
|||
And here's another one for you.
http://cgi.ebay.com/ws/eBayISAPI.dll...m=3849963 251 "mick" wrote in message news On Fri, 05 Nov 2004 00:15:41 +0000, Joe wrote: I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? I've used a Radford N15R power pack for preamp stages & similar low current stuff. Quite a few of these have been disposed of by schools over the years - they were originally used for the physics course before people decided that things like x-ray tubes were too dangerous for us kids! Get a smalli variac and use it to drive the primary of a reasonable mains tranny for the HT. Ignore the heater windings on this. This should be independently switched. SS rectifier & suitable caps rated for the full output (fit bleeder resistors and a voltmeter). Use second and possible third heater trannys, not fed via the variac. Also a seperate bias supply using a ww pot and giving up to say 100v should be ok for a lot of stuff. -- Mick (no M$ software on here... :-) ) Web: http://www.nascom.info |
#6
|
|||
|
|||
I was looking at this one already
Looks great wish I could afford to buy new stuff right now but oh well I have a good bench supply that is almost exactly like the Heathkit. 0-450V at 150ma and 0-150V 2ma and a pair of 6.3V 3A supplies does the job for now but I would love to have that 600V supply Doug wrote in message . .. And here's another one for you. http://cgi.ebay.com/ws/eBayISAPI.dll...m=3849963 251 "mick" wrote in message news On Fri, 05 Nov 2004 00:15:41 +0000, Joe wrote: I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? I've used a Radford N15R power pack for preamp stages & similar low current stuff. Quite a few of these have been disposed of by schools over the years - they were originally used for the physics course before people decided that things like x-ray tubes were too dangerous for us kids! Get a smalli variac and use it to drive the primary of a reasonable mains tranny for the HT. Ignore the heater windings on this. This should be independently switched. SS rectifier & suitable caps rated for the full output (fit bleeder resistors and a voltmeter). Use second and possible third heater trannys, not fed via the variac. Also a seperate bias supply using a ww pot and giving up to say 100v should be ok for a lot of stuff. -- Mick (no M$ software on here... :-) ) Web: http://www.nascom.info |
#7
|
|||
|
|||
Joe,
I have an extra Heathkit power supply that I would sell for a reasonable price. Please reply to the group if you are interested. BTW, I tried to reply to the post but my email was bounced back. Regards, Mark "Joe" wrote in message ... I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? Thanks! Joe |
#8
|
|||
|
|||
Thanks a lot for all the great suggestions. I really like the idea of using a variac to control the mains - hadn't thought of doing that. I ended up buying a Heathkit IP-17 from a buddy of mine at work. It's in great shape and has outputs similar to the IP-32. He told me that the regulation was good, but not superior - which I think is fine for what I'm doing. I did find an interesting web page where these fellows had modified an IP-17 to create a microprocessor controlled HV supply. http://www.tech-diy.com/MCTracer_no_...webversion.htm Not quite what I'm looking to do, but interesting nonetheless. On Fri, 05 Nov 2004 00:15:41 GMT, Joe wrote: I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? Thanks! Joe |
#9
|
|||
|
|||
Joe wrote: Thanks a lot for all the great suggestions. I really like the idea of using a variac to control the mains - hadn't thought of doing that. That takes a seperate tranny for the fillaments, and they can go a lot higher than 2A. A pair of EL34's or 6550's will draw 3A. I'm building one with seperate supplies for 5V @ 4A and 6.3V @ 8A. The Variac will be hooked up to a 5:1 step-up transformer for forming 'lytics. I'm still looking for a regulator circuit, though. I've seen one by Dan Torres that used a 6BM8 tube, but I've lost the scematic. |
#10
|
|||
|
|||
Yes, I was thinking two variacs and two transformers (one set each for plate and bias supplies) might be a good idea. Then perhaps another transformer for the 5V & 6V supplies. I found a set of website that discusses tube-based regulation and error control circuits - including schematics and test results. http://members.aol.com/sbench/reg1.html It was well researched and presented, I thought. On 7 Nov 2004 10:58:42 -0800, "kseely" wrote: Joe wrote: Thanks a lot for all the great suggestions. I really like the idea of using a variac to control the mains - hadn't thought of doing that. That takes a seperate tranny for the fillaments, and they can go a lot higher than 2A. A pair of EL34's or 6550's will draw 3A. I'm building one with seperate supplies for 5V @ 4A and 6.3V @ 8A. The Variac will be hooked up to a 5:1 step-up transformer for forming 'lytics. I'm still looking for a regulator circuit, though. I've seen one by Dan Torres that used a 6BM8 tube, but I've lost the scematic. |
#11
|
|||
|
|||
Look around for a Fluke 407 or 407D. Best looking piece of gear I ever
owned - big knobs, huge meter. 6.3vAC filaments @ 10A, B+ adjust to 550VDC @300mA, bias adj to -250V. B+ & bias are well regulated. fils are sort of regulated w/ ballast tube. Mine has been working non stop for 10 years and it was probably 30 years old when I got it though I did re-cap it. Todd Joe wrote: I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? Thanks! Joe |
#12
|
|||
|
|||
Yes,
IP-17 is the way to go! ebay can make them very affordable if you have time to buy. Giles On Sun, 07 Nov 2004 17:07:56 GMT, Joe wrotf: Thanks a lot for all the great suggestions. I really like the idea of using a variac to control the mains - hadn't thought of doing that. I ended up buying a Heathkit IP-17 from a buddy of mine at work. It's in great shape and has outputs similar to the IP-32. He told me that the regulation was good, but not superior - which I think is fine for what I'm doing. I did find an interesting web page where these fellows had modified an IP-17 to create a microprocessor controlled HV supply. http://www.tech-diy.com/MCTracer_no_...webversion.htm Not quite what I'm looking to do, but interesting nonetheless. On Fri, 05 Nov 2004 00:15:41 GMT, Joe wrote: I'm an electronics student interested in learning about tube amplifier circuits. I'm looking for a bench power supply to use for experimenting with some pre-amp designs, but I'm having trouble finding something suitable. Based on the reading I've done, I was thinking the PS should be variable from about 150VDC to 400VDC @100mA for the plates, and fixed at about 6VAC @ 2A and 5VDC @ 2A for the heaters. Maybe I'm way off base here, but I can't seem to find anything like this. Does anyone know of any bench supplies, or kits, or schematics like this - or have other suggestions? Thanks! Joe |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
CLC: More | Vacuum Tubes | |||
here is how firewire ports fail | Pro Audio | |||
List of NOS mostly tubes | Vacuum Tubes | |||
Clean Power? | Car Audio | |||
old solid state circa 70-80's` | Audio Opinions |