Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Attach speakers digitally
Hi!
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. Any help appreciated, Kevin |
#2
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. What are you attaching the speakers *TO*? If you are talking about "computer speakers", there are at least a few speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. I saw one the other day over at my neighborhood "big box" discount store (Costco). If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. |
#3
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. What are you attaching the speakers *TO*? If you are talking about "computer speakers", there are at least a few speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. I saw one the other day over at my neighborhood "big box" discount store (Costco). If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. |
#4
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. What are you attaching the speakers *TO*? If you are talking about "computer speakers", there are at least a few speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. I saw one the other day over at my neighborhood "big box" discount store (Costco). If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. |
#5
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. What are you attaching the speakers *TO*? If you are talking about "computer speakers", there are at least a few speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. I saw one the other day over at my neighborhood "big box" discount store (Costco). If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. |
#6
|
|||
|
|||
Attach speakers digitally
On Wed, 3 Mar 2004 07:13:39 -0800, "Richard Crowley"
wrote: If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. Actually, I know of few. The best examples are from Meridian's DSP line. The overwhelming majority of high quality home loudspeakers are completely analog. Kal |
#7
|
|||
|
|||
Attach speakers digitally
On Wed, 3 Mar 2004 07:13:39 -0800, "Richard Crowley"
wrote: If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. Actually, I know of few. The best examples are from Meridian's DSP line. The overwhelming majority of high quality home loudspeakers are completely analog. Kal |
#8
|
|||
|
|||
Attach speakers digitally
On Wed, 3 Mar 2004 07:13:39 -0800, "Richard Crowley"
wrote: If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. Actually, I know of few. The best examples are from Meridian's DSP line. The overwhelming majority of high quality home loudspeakers are completely analog. Kal |
#9
|
|||
|
|||
Attach speakers digitally
On Wed, 3 Mar 2004 07:13:39 -0800, "Richard Crowley"
wrote: If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. Actually, I know of few. The best examples are from Meridian's DSP line. The overwhelming majority of high quality home loudspeakers are completely analog. Kal |
#10
|
|||
|
|||
Attach speakers digitally
Hi!
Thanks for your answer! If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. HAND, Kevin |
#11
|
|||
|
|||
Attach speakers digitally
Hi!
Thanks for your answer! If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. HAND, Kevin |
#12
|
|||
|
|||
Attach speakers digitally
Hi!
Thanks for your answer! If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. HAND, Kevin |
#13
|
|||
|
|||
Attach speakers digitally
Hi!
Thanks for your answer! If you are talking about "hi-fi speakers" (in your living room/home theater, etc.), there are likely speakers with integrated digital inputs and amplifier(s), but you are likely talking about high-end stuff at thousands of USD. This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. HAND, Kevin |
#14
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
Hi! I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. Any help appreciated, Kevin Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. |
#15
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
Hi! I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. Any help appreciated, Kevin Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. |
#16
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
Hi! I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. Any help appreciated, Kevin Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. |
#17
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
Hi! I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. Any help appreciated, Kevin Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. |
#18
|
|||
|
|||
Attach speakers digitally
Kevin Boergens writes:
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? In the computer world there are speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. There are also speakers for example in professional monitor speaker market with S/PDIF digital interface (for example GENELEC 2029A). I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. I think that S/PDIF is the right thing to use. It is well standardized, there is wide selection of suitable ICs for handling the signal, equipment with digital output most often give this kind of signal output directly. etc. S/PDIF sounds like a pretty good idea to me, even though you only use half of it's bandwidth per speaker. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. You need the decoders in the boxes, that's for sure. You don't need any fancy special splitter for going to both boxes. Baically you can build the system in such way that you always feed the same full stereo signal to both speakers, and the speakers just pick up the channel you want to play out through it and forger everything else coming in. You cna foe example have two identical speakers with S/PDIF input and switch on the back to selec which channel audio to play back (just set left speaker to left channel and right speaker to right channel and things work). For splitting the audio from one source to two speakers, you bascially need some form of passive signal splitter or active splitter amplifier that can run two outptu cables from one signal source. Passive splitters will do if you don't have too lign cables or have sensitive enough S/PDIF signal receivers to get slightly weaker than normal signals. Passive splitter for coaxial S/PDIF if just simply a tranformer with one primary coil and two secondary coils (with slightly less turns than primary), that does the impedance matching. Active solitter would be something quite similar to a vidoe disribution amplifier or s/ODIF inut amplifier + two S/PDIF driver circuits. For optical Toslink interface, I quess that a simple optical signal splitter would work well (I quess I have seem somethign like this for sale somewhere quite cheaply). Any help appreciated, Kevin Hopefullymy tips helped you. -- Tomi Engdahl (http://www.iki.fi/then/) Take a look at my electronics web links and documents at http://www.epanorama.net/ |
#19
|
|||
|
|||
Attach speakers digitally
Kevin Boergens writes:
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? In the computer world there are speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. There are also speakers for example in professional monitor speaker market with S/PDIF digital interface (for example GENELEC 2029A). I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. I think that S/PDIF is the right thing to use. It is well standardized, there is wide selection of suitable ICs for handling the signal, equipment with digital output most often give this kind of signal output directly. etc. S/PDIF sounds like a pretty good idea to me, even though you only use half of it's bandwidth per speaker. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. You need the decoders in the boxes, that's for sure. You don't need any fancy special splitter for going to both boxes. Baically you can build the system in such way that you always feed the same full stereo signal to both speakers, and the speakers just pick up the channel you want to play out through it and forger everything else coming in. You cna foe example have two identical speakers with S/PDIF input and switch on the back to selec which channel audio to play back (just set left speaker to left channel and right speaker to right channel and things work). For splitting the audio from one source to two speakers, you bascially need some form of passive signal splitter or active splitter amplifier that can run two outptu cables from one signal source. Passive splitters will do if you don't have too lign cables or have sensitive enough S/PDIF signal receivers to get slightly weaker than normal signals. Passive splitter for coaxial S/PDIF if just simply a tranformer with one primary coil and two secondary coils (with slightly less turns than primary), that does the impedance matching. Active solitter would be something quite similar to a vidoe disribution amplifier or s/ODIF inut amplifier + two S/PDIF driver circuits. For optical Toslink interface, I quess that a simple optical signal splitter would work well (I quess I have seem somethign like this for sale somewhere quite cheaply). Any help appreciated, Kevin Hopefullymy tips helped you. -- Tomi Engdahl (http://www.iki.fi/then/) Take a look at my electronics web links and documents at http://www.epanorama.net/ |
#20
|
|||
|
|||
Attach speakers digitally
Kevin Boergens writes:
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? In the computer world there are speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. There are also speakers for example in professional monitor speaker market with S/PDIF digital interface (for example GENELEC 2029A). I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. I think that S/PDIF is the right thing to use. It is well standardized, there is wide selection of suitable ICs for handling the signal, equipment with digital output most often give this kind of signal output directly. etc. S/PDIF sounds like a pretty good idea to me, even though you only use half of it's bandwidth per speaker. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. You need the decoders in the boxes, that's for sure. You don't need any fancy special splitter for going to both boxes. Baically you can build the system in such way that you always feed the same full stereo signal to both speakers, and the speakers just pick up the channel you want to play out through it and forger everything else coming in. You cna foe example have two identical speakers with S/PDIF input and switch on the back to selec which channel audio to play back (just set left speaker to left channel and right speaker to right channel and things work). For splitting the audio from one source to two speakers, you bascially need some form of passive signal splitter or active splitter amplifier that can run two outptu cables from one signal source. Passive splitters will do if you don't have too lign cables or have sensitive enough S/PDIF signal receivers to get slightly weaker than normal signals. Passive splitter for coaxial S/PDIF if just simply a tranformer with one primary coil and two secondary coils (with slightly less turns than primary), that does the impedance matching. Active solitter would be something quite similar to a vidoe disribution amplifier or s/ODIF inut amplifier + two S/PDIF driver circuits. For optical Toslink interface, I quess that a simple optical signal splitter would work well (I quess I have seem somethign like this for sale somewhere quite cheaply). Any help appreciated, Kevin Hopefullymy tips helped you. -- Tomi Engdahl (http://www.iki.fi/then/) Take a look at my electronics web links and documents at http://www.epanorama.net/ |
#21
|
|||
|
|||
Attach speakers digitally
Kevin Boergens writes:
I have an idea and I'd like to hear your opinion about it: I'd like to build digital speakers. That means that even the bus to the speakers in is digitals. Making the signal analog will be done within the boxes. Is there anyone selling such boxes? If not, what kind of bus would you use? In the computer world there are speakers out there that attach with USB and perform the D/A conversion and amplification within the speakers. There are also speakers for example in professional monitor speaker market with S/PDIF digital interface (for example GENELEC 2029A). I'm not sure whether S/PDIF is the right thing for me because I have to transport only one channel. I think that S/PDIF is the right thing to use. It is well standardized, there is wide selection of suitable ICs for handling the signal, equipment with digital output most often give this kind of signal output directly. etc. S/PDIF sounds like a pretty good idea to me, even though you only use half of it's bandwidth per speaker. And even if, I still need to split the signal before going to the boxes and chips with are capable of decoding the stream. You need the decoders in the boxes, that's for sure. You don't need any fancy special splitter for going to both boxes. Baically you can build the system in such way that you always feed the same full stereo signal to both speakers, and the speakers just pick up the channel you want to play out through it and forger everything else coming in. You cna foe example have two identical speakers with S/PDIF input and switch on the back to selec which channel audio to play back (just set left speaker to left channel and right speaker to right channel and things work). For splitting the audio from one source to two speakers, you bascially need some form of passive signal splitter or active splitter amplifier that can run two outptu cables from one signal source. Passive splitters will do if you don't have too lign cables or have sensitive enough S/PDIF signal receivers to get slightly weaker than normal signals. Passive splitter for coaxial S/PDIF if just simply a tranformer with one primary coil and two secondary coils (with slightly less turns than primary), that does the impedance matching. Active solitter would be something quite similar to a vidoe disribution amplifier or s/ODIF inut amplifier + two S/PDIF driver circuits. For optical Toslink interface, I quess that a simple optical signal splitter would work well (I quess I have seem somethign like this for sale somewhere quite cheaply). Any help appreciated, Kevin Hopefullymy tips helped you. -- Tomi Engdahl (http://www.iki.fi/then/) Take a look at my electronics web links and documents at http://www.epanorama.net/ |
#22
|
|||
|
|||
Attach speakers digitally
Hi!
Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. I'm a bit shocked about your post! I'm really not the one who must be warned about the dangers of DRM/TCPA .I just don't see this connection. Of course DRM wouldn't be possible if there was only analog music, but the differences between a semi-digital and a completely digital world are very small. Getting rid of DRM in a semi digital world Analog sound out jack 0=----; | | Analog sound in jack 0=----' Getting rid of DRM in a complete digital world ---=0~~~~|D/A|------|A/D|~~~~0=----- But both doesn't save one, because this new document is worldwide identifable as made by you so you will be ****ed as well. HAND, Kevin |
#23
|
|||
|
|||
Attach speakers digitally
Hi!
Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. I'm a bit shocked about your post! I'm really not the one who must be warned about the dangers of DRM/TCPA .I just don't see this connection. Of course DRM wouldn't be possible if there was only analog music, but the differences between a semi-digital and a completely digital world are very small. Getting rid of DRM in a semi digital world Analog sound out jack 0=----; | | Analog sound in jack 0=----' Getting rid of DRM in a complete digital world ---=0~~~~|D/A|------|A/D|~~~~0=----- But both doesn't save one, because this new document is worldwide identifable as made by you so you will be ****ed as well. HAND, Kevin |
#24
|
|||
|
|||
Attach speakers digitally
Hi!
Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. I'm a bit shocked about your post! I'm really not the one who must be warned about the dangers of DRM/TCPA .I just don't see this connection. Of course DRM wouldn't be possible if there was only analog music, but the differences between a semi-digital and a completely digital world are very small. Getting rid of DRM in a semi digital world Analog sound out jack 0=----; | | Analog sound in jack 0=----' Getting rid of DRM in a complete digital world ---=0~~~~|D/A|------|A/D|~~~~0=----- But both doesn't save one, because this new document is worldwide identifable as made by you so you will be ****ed as well. HAND, Kevin |
#25
|
|||
|
|||
Attach speakers digitally
Hi!
Computer hardware makers are already headed in this direction so as to keep you from ever being able to make an analog recording of anything. It's called Digital Rights Management and the rights being protected are not those of the consumer. I'm a bit shocked about your post! I'm really not the one who must be warned about the dangers of DRM/TCPA .I just don't see this connection. Of course DRM wouldn't be possible if there was only analog music, but the differences between a semi-digital and a completely digital world are very small. Getting rid of DRM in a semi digital world Analog sound out jack 0=----; | | Analog sound in jack 0=----' Getting rid of DRM in a complete digital world ---=0~~~~|D/A|------|A/D|~~~~0=----- But both doesn't save one, because this new document is worldwide identifable as made by you so you will be ****ed as well. HAND, Kevin |
#26
|
|||
|
|||
Attach speakers digitally
Hi!
It is well standardized, there is wide selection of suitable ICs for handling the signal, Is the price of them something to worry about? Hopefullymy tips helped you. Yes! You are great. HAND, Kevin BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? |
#27
|
|||
|
|||
Attach speakers digitally
Hi!
It is well standardized, there is wide selection of suitable ICs for handling the signal, Is the price of them something to worry about? Hopefullymy tips helped you. Yes! You are great. HAND, Kevin BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? |
#28
|
|||
|
|||
Attach speakers digitally
Hi!
It is well standardized, there is wide selection of suitable ICs for handling the signal, Is the price of them something to worry about? Hopefullymy tips helped you. Yes! You are great. HAND, Kevin BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? |
#29
|
|||
|
|||
Attach speakers digitally
Hi!
It is well standardized, there is wide selection of suitable ICs for handling the signal, Is the price of them something to worry about? Hopefullymy tips helped you. Yes! You are great. HAND, Kevin BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? |
#30
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. It is most likely cheaper (and most certainly easier) to use good-quality (NOT "name brand" boutique) cable. Not saying that it would be an interesting experiment, but you would be trading artifacts caused by your wiring for artifacts caused by your home-made D/A converter. |
#31
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. It is most likely cheaper (and most certainly easier) to use good-quality (NOT "name brand" boutique) cable. Not saying that it would be an interesting experiment, but you would be trading artifacts caused by your wiring for artifacts caused by your home-made D/A converter. |
#32
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. It is most likely cheaper (and most certainly easier) to use good-quality (NOT "name brand" boutique) cable. Not saying that it would be an interesting experiment, but you would be trading artifacts caused by your wiring for artifacts caused by your home-made D/A converter. |
#33
|
|||
|
|||
Attach speakers digitally
"Kevin Boergens" wrote ...
This comes quite near my idea. I just wanted to take a couple of good active speakers(~300USD, don't know whether you'd call this good, but the room to fill with sound is only 28 cubicmeters) , and put D/A-chips inside to be able to connect them to my equipment. I have only digital equipment, so it seemed a cool idea to me to have as less analog cable as possible. It is most likely cheaper (and most certainly easier) to use good-quality (NOT "name brand" boutique) cable. Not saying that it would be an interesting experiment, but you would be trading artifacts caused by your wiring for artifacts caused by your home-made D/A converter. |
#34
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
---snip--- BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? Yes, or at least it is supposed to be. |
#35
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
---snip--- BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? Yes, or at least it is supposed to be. |
#36
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
---snip--- BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? Yes, or at least it is supposed to be. |
#37
|
|||
|
|||
Attach speakers digitally
Kevin Boergens wrote in message ...
---snip--- BTW: Most CD-ROM drives have a two pin output called digital-something. Is this a S/PDIF output? Yes, or at least it is supposed to be. |
#38
|
|||
|
|||
Attach speakers digitally
|
#39
|
|||
|
|||
Attach speakers digitally
|
Reply |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
rec.audio.car FAQ (Part 4/5) | Car Audio | |||
AER Pisces PB-651 V2.0 speaker review | Tech | |||
P/review of Jupiter Audio Europa speakers pt.1 | Audio Opinions |