[jimbo_limited]

i had purchased 2 DVC 4 ohm subs. For each coil, is it rated at 4 ohm or its overall rating is 4 ohm and i was wondering if i can wire it to a One ohm load?

If the sub is a dual 4ohm then both coils are 4ohm. You can get a 1ohm load
by wiring them both in parallel, this will give you a 2ohm load per sub.

In article , jimbo_limited
wrote:

i had purchased 2 DVC 4 ohm subs. For each coil, is it rated at 4 ohm
or its overall rating is 4 ohm and i was wondering if i can wire it to
a One ohm load?

Yes, This graphic might help you visually.

http://showcase.netins.net/web/aioka/Speaker/dual.jpg

-Branden

"jimbo_limited" wrote in message
...

i had purchased 2 DVC 4 ohm subs. For each coil, is it rated at 4 ohm
or its overall rating is 4 ohm and i was wondering if i can wire it to
a One ohm load?


--
jimbo_limited

Is the amplifier 1 ohm stable?

"jimbo_limited" wrote in message
...

i had purchased 2 DVC 4 ohm subs. For each coil, is it rated at 4 ohm
or its overall rating is 4 ohm and i was wondering if i can wire it to
a One ohm load?


--
jimbo_limited

Branden Nelsen wrote:
Yes, This graphic might help you visually.

http://showcase.netins.net/web/aioka/Speaker/dual.jpg

That would be handy if it was actually big enough to see anything.


---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0620-0, 05/15/2006
Tested on: 5/15/2006 11:24:31 AM
avast! - copyright (c) 1988-2006 ALWIL Software.
http://www.avast.com

Matt Ion Wrote:

That would be handy if it was actually big enough to see anything.

haha, indeed. but parallel wiring is easy, just wire all the positives
from both subs to the positive output on the amp, and all the negatives
to the negative output on the amp. that'll get you your final 1 ohm
load


--
KU40

Is the amplifier 1 ohm stable?

Damn good question. Very few 2 channel amps made today are 1 ohm bridged
stable (and even most mono amps are not 1 ohm stable). If your amp is not 1
ohm stable, you will likely fry your amp.

MOSFET

Its possible that its your IE settings. I run 1280x1024 and i can read it
just fine.

-Branden

"KU40" wrote in message
...

Matt Ion Wrote:

That would be handy if it was actually big enough to see anything.

haha, indeed. but parallel wiring is easy, just wire all the positives
from both subs to the positive output on the amp, and all the negatives
to the negative output on the amp. that'll get you your final 1 ohm
load


--
KU40

Branden Nelsen wrote:
Its possible that its your IE settings. I run 1280x1024 and i can read it
just fine.

Nothing to do with the browser - Firefox shows me the picture fully
scaled. It's too damn small on a 2048x1536 display.


---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0620-0, 05/15/2006
Tested on: 5/15/2006 7:59:27 PM
avast! - copyright (c) 1988-2006 ALWIL Software.
http://www.avast.com

Allot of things are too small on a 2048x1536 Res

-Branden

"Matt Ion" wrote in message
news:kebag.167958$WI1.129219@pd7tw2no...
Branden Nelsen wrote:
Its possible that its your IE settings. I run 1280x1024 and i can read it
just fine.

Nothing to do with the browser - Firefox shows me the picture fully
scaled. It's too damn small on a 2048x1536 display.


---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0620-0, 05/15/2006
Tested on: 5/15/2006 7:59:27 PM
avast! - copyright (c) 1988-2006 ALWIL Software.
http://www.avast.com

Not so much on a 21" monitor

Branden Nelsen wrote:
Allot of things are too small on a 2048x1536 Res

-Branden

"Matt Ion" wrote in message
news:kebag.167958$WI1.129219@pd7tw2no...

Branden Nelsen wrote:

Its possible that its your IE settings. I run 1280x1024 and i can read it
just fine.

Nothing to do with the browser - Firefox shows me the picture fully
scaled. It's too damn small on a 2048x1536 display.


---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0620-0, 05/15/2006
Tested on: 5/15/2006 7:59:27 PM
avast! - copyright (c) 1988-2006 ALWIL Software.
http://www.avast.com








---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0620-0, 05/15/2006
Tested on: 5/16/2006 9:53:45 PM
avast! - copyright (c) 1988-2006 ALWIL Software.
http://www.avast.com

You can also make the monitor to step down the resolution to 1024 (or other
value) with some shortcut key. This has better results than scaling down.

"Matt Ion" wrote in message
news:kebag.167958$WI1.129219@pd7tw2no...

| Nothing to do with the browser - Firefox shows me the picture fully
| scaled. It's too damn small on a 2048x1536 display.

[jimbo_limited]

Originally Posted by e-nigma

Is the amplifier 1 ohm stable?

"jimbo_limited" wrote in message
...

i had purchased 2 DVC 4 ohm subs. For each coil, is it rated at 4 ohm
or its overall rating is 4 ohm and i was wondering if i can wire it to
a One ohm load?


--
jimbo_limited

Yessir... my T10001 bd is 1 ohm stable.

I will be running some kicker solo baric L5. ^__^

"jimbo_limited" wrote in message
...

e-nigma Wrote:
Is the amplifier 1 ohm stable?

"jimbo_limited" wrote in message
...

i had purchased 2 DVC 4 ohm subs. For each coil, is it rated at 4
ohm
or its overall rating is 4 ohm and i was wondering if i can wire it
to
a One ohm load?


--
jimbo_limited



Yessir... my T10001 bd is 1 ohm stable.

I will be running some kicker solo baric L5. ^__^


--
jimbo_limited

Then just running all 4 voice coils in parallel will give you a 1 ohm load