Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
thats correct, you will have to be carefull not to blow out the speakers
though... go easy on the headunit vol knob. Garrett JohanWagener wrote: The way I understand it you can run a pair of 150W (30 nom) speakers off an 1500W (600RMS) at full volume without damaging the speakers. Is this true? |
#2
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
The way I understand it you can run a pair of 150W (30 nom) speakers off
an 1500W (600RMS) at full volume without damaging the speakers. Is this true? Not generally. If the amp is truly 600 watts and the speakers can truly handle only 30 watts, the chances are quite good that you'll blow the speakers. However, the amp you got ("Starsound") is probably actually rated about 50wrms x 4 at 4 ohms, huh? So much for a 1500 watt amp. |
#3
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
Starsound? sounds like a flea market $10 special?
"Mark Zarella" seesigfile wrote in message ... The way I understand it you can run a pair of 150W (30 nom) speakers off an 1500W (600RMS) at full volume without damaging the speakers. Is this true? Not generally. If the amp is truly 600 watts and the speakers can truly handle only 30 watts, the chances are quite good that you'll blow the speakers. However, the amp you got ("Starsound") is probably actually rated about 50wrms x 4 at 4 ohms, huh? So much for a 1500 watt amp. |
#4
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
In article ,
"JohanWagener" wrote: The way I understand it you can run a pair of 150W (30 nom) speakers off an 1500W (600RMS) at full volume without damaging the speakers. Is this true? No. Do the math. You're 5x past the limit of the speakers at full volume. You could burn the coil, rip the suspension, or maybe even degauss the magnet. |
#5
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
"Mark Zarella" seesigfile wrote in message ... The way I understand it you can run a pair of 150W (30 nom) speakers off an 1500W (600RMS) at full volume without damaging the speakers. Is this true? Not generally. If the amp is truly 600 watts and the speakers can truly handle only 30 watts, the chances are quite good that you'll blow the speakers. However, the amp you got ("Starsound") is probably actually rated about 50wrms x 4 at 4 ohms, huh? So much for a 1500 watt amp. Nope not really! !1500W music power. 600W RMS bridged or 100x4 unbridged. I've seen test performed on these before I bought it. Must say for the money I payed I'm quite impressed. |
#6
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
Nope not really! !1500W music power.
There's no such thing as "music power". 600W RMS bridged or 100x4 unbridged. I've seen test performed on these before I bought it. What kind of test? Must say for the money I payed I'm quite impressed. Maybe so, but realize that it's NOT 1500 watts. So if it's 100x4, and IF it truly delivers that output power, then powering 30 watt speakers could be pushing it (assuming that their ratings are accurate as well). Manufacturers, bad ones and top of the line ones, often lie about their published specs. |
#7
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
"Power can be measured for top to bottom of the signal (Peak, or Max, etc).
Another way to measure power is From the zero-level to the top half (usually called music power)." http://ccs.exl.info/frame_main.html |
#8
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
"Power can be measured for top to bottom of the signal (Peak, or Max,
etc). This is in fact false. Power is defined as a time rate of energy (Introduction to Electrodynamics, Griffiths; Classical Electrodynamics, Jackson; Thermodynamics of Materials, Hudson; Microelectronic Circuits, Sedra/Smith). That is, dP = DE/dt. As such, "max power", "music power", and "peak power", though often mathematically defined as the peak instantaneous power content of a sine wave, has no logical basis in the physical world. Put simply, "peak power" is defined as the power dissipated by something in an infinitesimal period of time. That's why in audio we use terms such as "average power" (often referred to as "RMS power", though this is a misnomer). Average power takes the time-rate into consideration and provides a useful parameter to us (especially when it comes to examining heat and temperature). "Peak power", then, is nothing more than a marketing ploy. And sorry to say, you fell for it hook, line, and sinker. You can't do anything with "peak power". You can deliver 15 billion watts in an infinitesimal time period to a 5 watt speaker without blowing it - of course you'd need superconductors to come anywhere close, and it still wouldn't be "peak power". Another way to measure power is From the zero-level to the top half (usually called music power)." "Music power". What on earth does a calculation which has no physical OR mathematical basis have to do with music? He's arbitrarily chosen a method of measurement and named it something. What good does such a parameter do for us? http://ccs.exl.info/frame_main.html I hope the references I provided above are sufficient. By the way, on his definition page in the references section, I count 18 errors in a matter of 9 short paragraphs (I'll list them if you want). I'd be careful about which references you choose to pay attention to. For future reference, you may want to bookmark the following site. It's much more reliable. http://www.eatel.net/~amptech/elecdisc/caraudio.htm |
#9
|
|||
|
|||
Running two 6" 150W speakers from 1500W amp
Yeah thanks Mark. Thats some good material compared to the **** I had to
read till now Yeah, the guy (whoever he is) did a really good job with that site. And that's a lot coming from me since I'm the most critical ******* around. |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Bose 901 Review | General | |||
Outdoor Speakers | General | |||
'89 Camry Recommendation | Car Audio | |||
Remote speakers? L-pads? Totally confused! | General | |||
Ford Escort Speakers? | Car Audio |