Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Opto-Compressors
Can someone explain the difference between Opto and electro to me? I see
opto on vintage and tubed compressors as well as some plugins like Waves Renaissance. Thanks! Dave |
#2
|
|||
|
|||
Opto-Compressors
DaveDrummer wrote:
Can someone explain the difference between Opto and electro to me? I see opto on vintage and tubed compressors as well as some plugins like Waves Renaissance. Thanks! Well, an optoelectric compressor is one that uses a light source (sometimes a neon bulb, sometimes an LED or an electroluminescent panel, sometimes just a plain old slow incandescent bulb), which illuminates with signal, and then a photoresistive cell that drops in resistance when light hits it, which shunts the signal to ground when the lamp lights up. This is one of the more common dynamic control designs from the days before we had effective voltage controlled amplifier circuits. Most of them aren't very fast, and most of them tend to have a fairly sharp knee because the lamp turns on fairly abruptly, but that's about all they really have in common in terms of general action. There is a nice discussion of these things in the RCA Radiotron Handbook. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#3
|
|||
|
|||
Opto-Compressors
Hi Dave read this article by Paul White, it will answer a lot of your
questions. http://www.soundonsound.com/sos/dec0...ompression.htm Regards, Sytze "DaveDrummer" schreef in bericht ... Can someone explain the difference between Opto and electro to me? I see opto on vintage and tubed compressors as well as some plugins like Waves Renaissance. Thanks! Dave |
#4
|
|||
|
|||
Opto-Compressors
In article writes: Can someone explain the difference between Opto and electro to me? Opto and electro? "Opto" is usually short for "optoelectronic" and it's one of the gain control elements that are used in compressors. The difference between them is the rate at which the gain (or attenuation) of the element changees when the control signal is applied. I wrote an article in Recording several years ago about the inner workings of compressors. See http://www.manleylabs.com for a slightly condensed (minus illustrations) version of the article. -- I'm really Mike Rivers ) However, until the spam goes away or Hell freezes over, lots of IP addresses are blocked from this system. If you e-mail me and it bounces, use your secret decoder ring and reach me he double-m-eleven-double-zero at yahoo |
#6
|
|||
|
|||
Opto-Compressors
Scott Dorsey wrote:
DaveDrummer wrote: Can someone explain the difference between Opto and electro to me? I see opto on vintage and tubed compressors as well as some plugins like Waves Renaissance. Thanks! Well, an optoelectric compressor is one that uses a light source (sometimes a neon bulb, sometimes an LED or an electroluminescent panel, sometimes just a plain old slow incandescent bulb), which illuminates with signal, and then a photoresistive cell that drops in resistance when light hits it, which shunts the signal to ground when the lamp lights up. Can also be configured in the feedback loop too since the controlled element is essentially a resistor. This is one of the more common dynamic control designs from the days before we had effective voltage controlled amplifier circuits. It's also very common now too. Increasingly so in fact. I've used nothing else since hmmm well.... earlyish 90's. I gave up on cheap VCAs ( transconductance amps ) after I found modern 'el-optos'. Expensive VCAs are ok - but an opto-cell always beats it on price. No set-up probs either. I got the msg when I heard there was a 1 yr lead time on the half decent VCA I might have used ! Most of them aren't very fast, and most of them tend to have a fairly sharp knee because the lamp turns on fairly abruptly, but that's about all they really have in common in terms of general action. They are actually very good now. If the 'lamp' is a led - which it *is* now - I've found you can plot a fairly reliable law between forward current and resistance. There's been a shake-up in the industry making these cells. In the past they were mainly made for the military. Now, they're mainly made for consumer apps. Leds are quick 'lamps' too. The photocell is somewhat less quick but modern materials technology has improved that beyond all recognition. Silonex ( Audiohm ) can offer special cells for high speed. The Chinese copies ( look in many Far East amplifiers ) are still a generation behind the likes of Silonex but I suggest you visit www.audiohm.com for a brief on the latest hot parts as used by Focusrite et al - also Studiomaster in the past too - lol. There is a nice discussion of these things in the RCA Radiotron Handbook. Haven't got that one. Graham |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
FS: Two DBX original 163 compressors #3936/393 | Pro Audio | |||
FS: Innovonics 201 Compressors | Pro Audio | |||
FS: Urie LA 4 Compressors | Pro Audio | |||
Hardware vs. Software Compressors | Pro Audio | |||
What is a Distressor ? | Pro Audio |