Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Amp toggle switch
I want to install a toggle switch to turn *one* of my amps on and off
and have some concerns... My wiring plan is as follows: - 12v accessory wire to 1 end of toggle switch terminal. - 18Awg wire connected to other terminal of the toggle switch. (This wire goes to the amp) Can I use a switch that is rated at 250 Vac for my application? Will I burn up the switch/contacts doing this? |
#2
|
|||
|
|||
the turn on circuit uses very little amperage. your switch should work fine.
"Mr. D" wrote in message ups.com... I want to install a toggle switch to turn *one* of my amps on and off and have some concerns... My wiring plan is as follows: - 12v accessory wire to 1 end of toggle switch terminal. - 18Awg wire connected to other terminal of the toggle switch. (This wire goes to the amp) Can I use a switch that is rated at 250 Vac for my application? Will I burn up the switch/contacts doing this? |
#3
|
|||
|
|||
That was my idea as well. Use a switch in line with the remote turn on wire.
Even a small valet over-ride switch like those that are part of a vehicle alarm system will do and they are easily hidden for a cleaner look. I use one in line for my antennae on my Trans Am so when I am not listening to the radio I can have my antennae in the down position. No sense in risking bending my antennae if I don't have to. Its possible; I had a barn owl fly (from the passengers side) right into the windshield of my F150 and bent the hell out of my antennae on the way by. Just glad it could be bent back. All I could think was : what if I were in the TA; EXPENSIVE!!! being it has the electric antennae. |
#4
|
|||
|
|||
the remote turn on will work just fine. I have the amp on/off switch and
used a Hella switch. Works perfectly. -- WDW is a Way of Life "Barry & Nikki" wrote in message ... That was my idea as well. Use a switch in line with the remote turn on wire. Even a small valet over-ride switch like those that are part of a vehicle alarm system will do and they are easily hidden for a cleaner look. I use one in line for my antennae on my Trans Am so when I am not listening to the radio I can have my antennae in the down position. No sense in risking bending my antennae if I don't have to. Its possible; I had a barn owl fly (from the passengers side) right into the windshield of my F150 and bent the hell out of my antennae on the way by. Just glad it could be bent back. All I could think was : what if I were in the TA; EXPENSIVE!!! being it has the electric antennae. |
#5
|
|||
|
|||
"Mr. D" wrote in message ups.com... I want to install a toggle switch to turn *one* of my amps on and off and have some concerns... If you can afford it buy a 300 or 400 dollar HU, they give you MUCH MUCH MORE control over your music and you can usually adjust the bass to your subs while not affecting the speakers. This way if you want to turn down the bass when in certain areas or while switching from rap to rock you can and you wont even have to wire in a switch or worry about burning up contacts. My wiring plan is as follows: - 12v accessory wire to 1 end of toggle switch terminal. - 18Awg wire connected to other terminal of the toggle switch. (This wire goes to the amp) Can I use a switch that is rated at 250 Vac for my application? Will I burn up the switch/contacts doing this? |
#6
|
|||
|
|||
"Sean Scott" Its@secret wrote in message ... "Mr. D" wrote in message ups.com... I want to install a toggle switch to turn *one* of my amps on and off and have some concerns... If you can afford it buy a 300 or 400 dollar HU, /snip/ or he can use the 99cent switch. |
#7
|
|||
|
|||
Sean Scott wrote:
If you can afford it buy a 300 or 400 dollar HU, they give you MUCH MUCH MORE control over your music and you can usually adjust the bass to your subs while not affecting the speakers. This way if you want to turn down the bass when in certain areas or while switching from rap to rock you can and you wont even have to wire in a switch or worry about burning up contacts. True, but I feel that by using a switch, I have just as good of control (maybe even more) as I would with an expensive headunit. Plus it's cheaper... Let's say I don't wish to use my subs... With my sub amp's remote turn on lead and my ignition's 12V switched wire wired to a toggle switch, I can switch off my sub amp, and my subs would be off. Not only that, but my sub's amp does not remain on unnecessarily. Now that I think of it, I think I'll wire all of my amps to seperate switches to give me even greater control of my system. Using a few $0.65 switches can prevent the risk of burning out a headunit's remote turn on circuit, and save the need of using relays. |
#8
|
|||
|
|||
What I was saying above is there is no need to even hook a switch to the 12V
power lead. Once the switch that you place on the remote turn on lead is turned on/off that will thoroughly control the power lead. The remote turn on lead is a switch in its own right that controls the power circuit. If the amp is not sensing that the head unit is turned on it won't turn on either. Being the amp turn on lead is such a minute amount of voltage there is no need to worry about burning anything up. Even taking the switch out of a kids toy will suffice for that; no worries about being underrated. "Mr. D" wrote in message oups.com... Sean Scott wrote: If you can afford it buy a 300 or 400 dollar HU, they give you MUCH MUCH MORE control over your music and you can usually adjust the bass to your subs while not affecting the speakers. This way if you want to turn down the bass when in certain areas or while switching from rap to rock you can and you wont even have to wire in a switch or worry about burning up contacts. True, but I feel that by using a switch, I have just as good of control (maybe even more) as I would with an expensive headunit. Plus it's cheaper... Let's say I don't wish to use my subs... With my sub amp's remote turn on lead and my ignition's 12V switched wire wired to a toggle switch, I can switch off my sub amp, and my subs would be off. Not only that, but my sub's amp does not remain on unnecessarily. Now that I think of it, I think I'll wire all of my amps to seperate switches to give me even greater control of my system. Using a few $0.65 switches can prevent the risk of burning out a headunit's remote turn on circuit, and save the need of using relays. |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Alps Power Switch in Tandberg 3012A | Pro Audio | |||
Alps Power Switch in Tandberg 3012A | Pro Audio | |||
Help needed for switch... | Pro Audio | |||
Questions on basic wirjing setup | Tech |