Reply
 
Thread Tools Display Modes
  #1   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Reinhard Zwirner Reinhard Zwirner is offline
external usenet poster
 
Posts: 18
Default HELP - Please Identify These Two Parts....................

EADGBE schrieb:

Actually, I'll do just a bit better.

Here are ALL of the circuit board traces, done as best as I can. Let
me know if the traces aren't clear enough:

http://i240.photobucket.com/albums/f...23/CIRCUIT.jpg

By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.


Obviously, you've forgotten the red connection:

http://www.bilder-hochladen.net/files/12b4-2t-jpg.html

HTH

Reinhard
  #2   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................


I have a "rainy afternoon project" that has got me puzzled.

I have an old Pioneer cassette deck that I am restoring.

The capstan motor worked for a short while, then it stopped.

The casing of the motor felt VERY warm, so I knew something was
amiss.

(One of the voltage regulators in the deck's main power supply became
EXTREMELY hot whenever the capstan motor was connected, which was
another clue).

Suspecting a short in the capstan motor, I took the motor apart.

Take a look at what I found when I examined the motor's internal
voltage regulator circuit board...

http://i240.photobucket.com/albums/f...3/SCORCHED.jpg

The motor's voltage regulator had burned itself up. Look at how
scorched the circuit board is!

I have a replacement regulator, but I want to make sure that all is
well inside this circuit before installing the replacement. (Yes, I
KNOW that I could simply get another motor, but remember, I am
tinkering for the sake of tinkering!)

So I have been checking all of the other components in this circuit,
to verify their health.

The one component that has me puzzled is the small black "diode"
indicated at the bottom of the photo.

There is no mark on this component other than the yellow stripe you
see.

I cannot get any type of reading on this component when I use my
multimeter -- I get nothing using my diode check function (forward or
reverse bias), no continuity, no resistance reading. It must be
faulty, I am assuming.

The other component that has me puzzled is the olive green "resistor"
just above the larger blue electrolytic capacitor. I get a steady
resistance reading of .5 ohms on this component.

I am going to disconnect at least one leg of each of these two
"mystery components" and take further readings, but I'm not used to
getting such odd readings right off the bat on these two components.

Can anyone provide any clues as to what these components are?

BY THE WAY, the motor is fed a steady voltage of 12.5 volts DC, with
no AC voltage ripple present. I have verified this.

Thanks In Advance.....
  #3   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
N_Cook N_Cook is offline
external usenet poster
 
Posts: 6
Default HELP - Please Identify These Two Parts....................

EADGBE wrote in message
...

I have a "rainy afternoon project" that has got me puzzled.

I have an old Pioneer cassette deck that I am restoring.

The capstan motor worked for a short while, then it stopped.

The casing of the motor felt VERY warm, so I knew something was
amiss.

(One of the voltage regulators in the deck's main power supply became
EXTREMELY hot whenever the capstan motor was connected, which was
another clue).

Suspecting a short in the capstan motor, I took the motor apart.

Take a look at what I found when I examined the motor's internal
voltage regulator circuit board...

http://i240.photobucket.com/albums/f...3/SCORCHED.jpg

The motor's voltage regulator had burned itself up. Look at how
scorched the circuit board is!

I have a replacement regulator, but I want to make sure that all is
well inside this circuit before installing the replacement. (Yes, I
KNOW that I could simply get another motor, but remember, I am
tinkering for the sake of tinkering!)

So I have been checking all of the other components in this circuit,
to verify their health.

The one component that has me puzzled is the small black "diode"
indicated at the bottom of the photo.

There is no mark on this component other than the yellow stripe you
see.

I cannot get any type of reading on this component when I use my
multimeter -- I get nothing using my diode check function (forward or
reverse bias), no continuity, no resistance reading. It must be
faulty, I am assuming.

The other component that has me puzzled is the olive green "resistor"
just above the larger blue electrolytic capacitor. I get a steady
resistance reading of .5 ohms on this component.

I am going to disconnect at least one leg of each of these two
"mystery components" and take further readings, but I'm not used to
getting such odd readings right off the bat on these two components.

Can anyone provide any clues as to what these components are?

BY THE WAY, the motor is fed a steady voltage of 12.5 volts DC, with
no AC voltage ripple present. I have verified this.

Thanks In Advance.....


Is the diode oriented to soak up back emfs from the motor ?
The green thing is an inductor

--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/





  #4   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Jamie[_2_] Jamie[_2_] is offline
external usenet poster
 
Posts: 36
Default HELP - Please Identify These Two Parts....................

EADGBE wrote:

I have a "rainy afternoon project" that has got me puzzled.

I have an old Pioneer cassette deck that I am restoring.

The capstan motor worked for a short while, then it stopped.

The casing of the motor felt VERY warm, so I knew something was
amiss.

(One of the voltage regulators in the deck's main power supply became
EXTREMELY hot whenever the capstan motor was connected, which was
another clue).

Suspecting a short in the capstan motor, I took the motor apart.

Take a look at what I found when I examined the motor's internal
voltage regulator circuit board...

http://i240.photobucket.com/albums/f...3/SCORCHED.jpg

The motor's voltage regulator had burned itself up. Look at how
scorched the circuit board is!

I have a replacement regulator, but I want to make sure that all is
well inside this circuit before installing the replacement. (Yes, I
KNOW that I could simply get another motor, but remember, I am
tinkering for the sake of tinkering!)

So I have been checking all of the other components in this circuit,
to verify their health.

The one component that has me puzzled is the small black "diode"
indicated at the bottom of the photo.

There is no mark on this component other than the yellow stripe you
see.

I cannot get any type of reading on this component when I use my
multimeter -- I get nothing using my diode check function (forward or
reverse bias), no continuity, no resistance reading. It must be
faulty, I am assuming.

The other component that has me puzzled is the olive green "resistor"
just above the larger blue electrolytic capacitor. I get a steady
resistance reading of .5 ohms on this component.

I am going to disconnect at least one leg of each of these two
"mystery components" and take further readings, but I'm not used to
getting such odd readings right off the bat on these two components.

Can anyone provide any clues as to what these components are?

BY THE WAY, the motor is fed a steady voltage of 12.5 volts DC, with
no AC voltage ripple present. I have verified this.

Thanks In Advance.....

Well, I guess you now know why the reg burt up.
that diode is suppose to go across the motor leads to suppress back
EMF which can damage components..
It would be a simply low current SI diode.


http://webpages.charter.net/jamie_5"

  #5   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................

The anode of the diode is attached directly to three of the resistors
as shown.

I have tried to re-create the circuit board traces on the other side.

The cathode connects to what N_Cook has described as an inductor.

Take a look at this photo:

http://i240.photobucket.com/albums/f...e123/DIODE.jpg

Thanks to everyone for your help so far.

Any chance of finding a replacement for this diode?


  #6   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................

Actually, I'll do just a bit better.

Here are ALL of the circuit board traces, done as best as I can. Let
me know if the traces aren't clear enough:

http://i240.photobucket.com/albums/f...23/CIRCUIT.jpg

By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.

  #7   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
PeterD PeterD is offline
external usenet poster
 
Posts: 124
Default HELP - Please Identify These Two Parts....................

On Sun, 5 Oct 2008 17:48:53 -0700 (PDT), EADGBE
wrote:

Actually, I'll do just a bit better.

Here are ALL of the circuit board traces, done as best as I can. Let
me know if the traces aren't clear enough:

http://i240.photobucket.com/albums/f...23/CIRCUIT.jpg

By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.


WHere does the motor winding itself attach? I'm guessing that the pins
on the 'bottom' of the image are teh power input, right?
  #8   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"EADGBE" wrote...
The one component that has me puzzled is the small black "diode"
indicated at the bottom of the photo.

There is no mark on this component other than the yellow stripe you
see.

I cannot get any type of reading on this component when I use my
multimeter -- I get nothing using my diode check function (forward or
reverse bias), no continuity, no resistance reading. It must be
faulty, I am assuming.


So are you saying that the resistance is "infinite" regardless
of how you try to measure it? If that is the case, then it is
likely "blown". Dunno how critical it is without the full
schematic diagram.

If it IS blown, then you should likely discover WHY before
replacing it or the replacement may blow instantly as well.

The other component that has me puzzled is the olive green "resistor"
just above the larger blue electrolytic capacitor. I get a steady
resistance reading of .5 ohms on this component.


Do you have some reason to believe that it is not just a
0.5 ohm resistor? Again, hard to guess without the full
schematic diagram.


  #9   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"EADGBE" wrote ...
The anode of the diode is attached directly to three of the resistors
as shown.

I have tried to re-create the circuit board traces on the other side.

The cathode connects to what N_Cook has described as an inductor.

Take a look at this photo:

http://i240.photobucket.com/albums/f...e123/DIODE.jpg

Thanks to everyone for your help so far.

Any chance of finding a replacement for this diode?


Depending on what the actual diagram looks like,
it is quite possibly a simple, generic silicon diode
like a 1N4001 (power rectifier) or maybe even a
popular signal diode like a 1N4148, etc. These
are both very common parts that likely cost only
a few cents in production quantities.


  #10   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"EADGBE" wrote ...
Actually, I'll do just a bit better.

Here are ALL of the circuit board traces, done as best as I can. Let
me know if the traces aren't clear enough:

http://i240.photobucket.com/albums/f...23/CIRCUIT.jpg


That is good, but you don't indicate which nodes connect to
the motor, and which are the power input (+ and -). Without
that critical info, it won;t be easy to make much sense out of
the circuit.

By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.


Are you SURE you have a replacement for this IC?
Panasonic lists it as an "application specific circuit"
(i.e. a custom-made chip, not a generic part). And it
says that it is "obsolete" (i.e. not made anymore). Also
there is no indication that it is a "regulator", or that it
has any replacement.

http://industrial.panasonic.com/www-...5+AN6601N+8+WW

Furthermore, the original was so burned up (as shown
by your excellent photo), that I would be reluctant to
just replace it without determining WHAT caused the
original to burn. I don't remember that you revealed
anything about the motor itself (impedances?, windings?,
brushes? mechanical rotation? etc.)




  #11   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Franc Zabkar Franc Zabkar is offline
external usenet poster
 
Posts: 15
Default HELP - Please Identify These Two Parts....................

On Sun, 5 Oct 2008 17:48:53 -0700 (PDT), EADGBE
put finger to keyboard and composed:

Actually, I'll do just a bit better.

Here are ALL of the circuit board traces, done as best as I can. Let
me know if the traces aren't clear enough:

http://i240.photobucket.com/albums/f...23/CIRCUIT.jpg

By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.


My vrt databook lists the TDA1151 and TDA1152 as equivalents for the
AN6610.

Here is a datasheet and application circuits for the TDA1151:
http://www.datasheetarchive.com/pdf-...DSA-633666.pdf

This is an equivalent NTE part:
http://www.nteinc.com/specs/7000to7099/pdf/nte7089.pdf

BTW, I think there is an error in your circuit diagram. AFAICT, there
is no DC current path from the IC's output pin and the negative
terminal of the motor.

As for the motor, I would clean out any carbon dust from between the
commutator segments.

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
  #12   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................


OK, here is the circuit again, this time with positive and negative
power inputs labeled....

http://i240.photobucket.com/albums/f.../CIRCUIT_2.jpg
  #13   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................


I should point something out that I haven't mentioned before...

There are two slots in the circuit board.

One of them is just above the smaller black electrolytic capacitor,
and the other slot is just below the larger blue electrolytic
capacitor.

You can see the traces going to these slots and appearing to "stop
dead".

These slots are where the motor contacts are soldered.
  #14   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"Franc Zabkar" wrote ...
EADGBE composed:
By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.


My vrt databook lists the TDA1151 and TDA1152 as equivalents for the
AN6610.


Which themselves are listed as "obsolete, discontinued, or hard-to-find".
IMHO, doesn't seem worth the effort for an 87-cent motor. YMMV


  #15   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"EADGBE" wrote...
I should point something out that I haven't mentioned before...
There are two slots in the circuit board.

One of them is just above the smaller black electrolytic capacitor,
and the other slot is just below the larger blue electrolytic
capacitor.

You can see the traces going to these slots and appearing to "stop
dead".

These slots are where the motor contacts are soldered.


Then it appears that you didn't trace the circuit properly.

According to your green lines, the only path from the
upper motor node is through the adjustable resistor
at the top (highly unlikely for such a high impedance
as 5000 ohms) or through the black electrolytic
capacitor (electrically impossible).

How about just posting a photo of the BACK of the
board instead of trying to interpret it?

There IS a direct path from the +power input to the
lower motor node, which seems consistent with the
motor speed regulator IC circuit.

Did you say that you *have* a replacement for the
semiconductor in hand, or that you had simply
identified it?




  #16   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Franc Zabkar Franc Zabkar is offline
external usenet poster
 
Posts: 15
Default HELP - Please Identify These Two Parts....................

On Sun, 5 Oct 2008 20:56:11 -0700, "Richard Crowley"
put finger to keyboard and composed:

"Franc Zabkar" wrote ...
EADGBE composed:
By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.


My vrt databook lists the TDA1151 and TDA1152 as equivalents for the
AN6610.


Which themselves are listed as "obsolete, discontinued, or hard-to-find".
IMHO, doesn't seem worth the effort for an 87-cent motor. YMMV


I can buy the AN6610 here in Australia for AU$2.75.

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
  #17   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"Franc Zabkar" wrote ...
"Richard Crowley" composed:
"Franc Zabkar" wrote ...
EADGBE composed:
By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.

My vrt databook lists the TDA1151 and TDA1152 as equivalents for the
AN6610.


Which themselves are listed as "obsolete, discontinued, or hard-to-find".
IMHO, doesn't seem worth the effort for an 87-cent motor. YMMV


I can buy the AN6610 here in Australia for AU$2.75.


OK, then that would mean paying AU$2.75 to repair a motor
that likely isn't worth half that. Not to mention that without
knowing why the original blew, the OP has an excellent chance
of blowing up the replacement instantly. That doesn't make
sense up here in the Northern Hemisphere. Perhaps things
look different from your perspective. :-)


  #18   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Kevin McMurtrie[_2_] Kevin McMurtrie[_2_] is offline
external usenet poster
 
Posts: 24
Default HELP - Please Identify These Two Parts....................

In article ,
"Richard Crowley" wrote:

"EADGBE" wrote ...
The anode of the diode is attached directly to three of the resistors
as shown.

I have tried to re-create the circuit board traces on the other side.

The cathode connects to what N_Cook has described as an inductor.

Take a look at this photo:

http://i240.photobucket.com/albums/f...e123/DIODE.jpg

Thanks to everyone for your help so far.

Any chance of finding a replacement for this diode?


Depending on what the actual diagram looks like,
it is quite possibly a simple, generic silicon diode
like a 1N4001 (power rectifier) or maybe even a
popular signal diode like a 1N4148, etc. These
are both very common parts that likely cost only
a few cents in production quantities.


I believe it takes at least two transistors. It's a positive feedback
system to compensate for losses in the motor, creating a virtual perfect
motor that doesn't change speeds under load. And that brings about the
second problem...

The circuit has only one pot so it's not going to work on a worn motor.
The loss compensation is a fixed resistor so it's only good for a motor
in perfect condition.

--
Google is a pro-spamming service. I will not see your reply if you use Google.
  #19   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Tim Schwartz Tim Schwartz is offline
external usenet poster
 
Posts: 62
Default HELP - Please Identify These Two Parts....- The motor itself

Hello,

Don't forget the motor itself

Only one person mentioned in passing that you should check the actual
motor. This is really critical. It is common for the motor itself to
be drawing WAY too much current because of brush dust contamination and
maybe a seized bearing.

Try powering the motor directly (no board) off a 6 volt or so power
supply with an amp meter in the line. Unloaded I'd think it should draw
well under 100mA in current. The motor being in trouble is what
probably caused the IC to run way to hot to begin with.

Regards,
Tim Schwartz
Bristol Electronics


EADGBE wrote:
I have a "rainy afternoon project" that has got me puzzled.

I have an old Pioneer cassette deck that I am restoring.

The capstan motor worked for a short while, then it stopped.

The casing of the motor felt VERY warm, so I knew something was
amiss.

(One of the voltage regulators in the deck's main power supply became
EXTREMELY hot whenever the capstan motor was connected, which was
another clue).

Suspecting a short in the capstan motor, I took the motor apart.

Take a look at what I found when I examined the motor's internal
voltage regulator circuit board...

http://i240.photobucket.com/albums/f...3/SCORCHED.jpg

The motor's voltage regulator had burned itself up. Look at how
scorched the circuit board is!

I have a replacement regulator, but I want to make sure that all is
well inside this circuit before installing the replacement. (Yes, I
KNOW that I could simply get another motor, but remember, I am
tinkering for the sake of tinkering!)

So I have been checking all of the other components in this circuit,
to verify their health.

The one component that has me puzzled is the small black "diode"
indicated at the bottom of the photo.

There is no mark on this component other than the yellow stripe you
see.

I cannot get any type of reading on this component when I use my
multimeter -- I get nothing using my diode check function (forward or
reverse bias), no continuity, no resistance reading. It must be
faulty, I am assuming.

The other component that has me puzzled is the olive green "resistor"
just above the larger blue electrolytic capacitor. I get a steady
resistance reading of .5 ohms on this component.

I am going to disconnect at least one leg of each of these two
"mystery components" and take further readings, but I'm not used to
getting such odd readings right off the bat on these two components.

Can anyone provide any clues as to what these components are?

BY THE WAY, the motor is fed a steady voltage of 12.5 volts DC, with
no AC voltage ripple present. I have verified this.

Thanks In Advance.....

  #20   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....- The motor itself

Richard:

Per your request, I have taken a photo of the back of the circuit
board.

http://i240.photobucket.com/albums/f.../CIRCUIT_3.jpg

I have numbered all of the connections so that no one will get
"lost".

They are as follows:

1 - speed control pot connections
2 - 43k resistor
3 - 332 ohm(?) resistor (orange/orange/red?/black/brown)
4 - 421M ohm(?) resistor (yellow/red/orange?/blue/green?)
5 - inductor (olive "resistor" shaped part)
6a - negative lead of 10uF/25v electrolytic
6b - positive lead of 10uF/25v electrolytic
7a - negative lead of 3.3uF/25v electrolytic
7b - positive lead of 3.3uF/25v electrolytic
8 - pink "resistor" (red/red/brown/grey/black)
9 - 22 ohm green resistor (red/red/black/silver)
10a - cathode of black diode (yellow stripe is closest to this
connection)
10b - anode of black diode

The positive and negative power connections are also indicated.

SOME QUICK ADDITIONAL COMMENTS, based on comments I have received so
far....

REMINDER: I know that I could easily get another motor. I AM SIMPLY
TINKERING FOR THE SAKE OF TINKERING, and it's a good opportunity to
learn a bit about this circuit. That's all!

Someone said that they found a substitute for AN6610, but that is NOT
the part number. The burned part says "AN6601". It is made by
Matsu****a (Panasonic). I do indeed have an exact replacement for
this part in hand. I found it online at a supplier specializing in
obsolete semiconductors.

I have tested the motor by running 9 volts directly into it. The
motor runs smoothly and quietly. I will take a current reading, just
to see what I find. But the motor appears to be OK.

I am currently going on the assumption that AN6601 failed on its own
and/or because of the fault of the diode.




  #21   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"Kevin McMurtrie" wrote ...
"Richard Crowley" wrote:
"EADGBE" wrote ...
The anode of the diode is attached directly to three of the resistors
as shown.

I have tried to re-create the circuit board traces on the other side.

The cathode connects to what N_Cook has described as an inductor.

Take a look at this photo:

http://i240.photobucket.com/albums/f...e123/DIODE.jpg

Thanks to everyone for your help so far.

Any chance of finding a replacement for this diode?


Depending on what the actual diagram looks like,
it is quite possibly a simple, generic silicon diode
like a 1N4001 (power rectifier) or maybe even a
popular signal diode like a 1N4148, etc. These
are both very common parts that likely cost only
a few cents in production quantities.


I believe it takes at least two transistors. It's a positive feedback
system to compensate for losses in the motor, creating a virtual perfect
motor that doesn't change speeds under load. And that brings about the
second problem...


It *has* likely several transistiors inside the TO-92
plastic package that burned up. Refer to the diagram
for the cited integrated circuit.

The circuit has only one pot so it's not going to work on a worn motor.
The loss compensation is a fixed resistor so it's only good for a motor
in perfect condition.


It doesn't need more than one pot. The regulator
compensates for the variations in the motor. Refer
to the diagram for the cited integrated circuit.

Google is a pro-spamming service.


Agreed.

I will not see your reply if you use Google.


Since the OP is posting from Google, you will have a hard time
following this discussion.


  #22   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
msg msg is offline
external usenet poster
 
Posts: 20
Default HELP - Please Identify These Two Parts....- The motor itself

EADGBE wrote:

snip

I do indeed have an exact replacement for
this part in hand. I found it online at a supplier specializing in
obsolete semiconductors.


Please reveal your source; I have had _no_ luck finding obsolete
parts houses that sell ICs in small quantities.

Michael
  #23   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Franc Zabkar Franc Zabkar is offline
external usenet poster
 
Posts: 15
Default HELP - Please Identify These Two Parts....................

On Sun, 5 Oct 2008 22:29:42 -0700, "Richard Crowley"
put finger to keyboard and composed:

"Franc Zabkar" wrote ...
"Richard Crowley" composed:
"Franc Zabkar" wrote ...
EADGBE composed:
By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.

My vrt databook lists the TDA1151 and TDA1152 as equivalents for the
AN6610.

Which themselves are listed as "obsolete, discontinued, or hard-to-find".
IMHO, doesn't seem worth the effort for an 87-cent motor. YMMV


I can buy the AN6610 here in Australia for AU$2.75.


OK, then that would mean paying AU$2.75 to repair a motor
that likely isn't worth half that. Not to mention that without
knowing why the original blew, the OP has an excellent chance
of blowing up the replacement instantly. That doesn't make
sense up here in the Northern Hemisphere. Perhaps things
look different from your perspective. :-)


I just realised the OP's IC is an AN6601, whereas I've been looking
for an AN6610. smacks forehead

Anyway, if the motor is an odd type, or if the pulley is difficult to
remove, then it may make sense to try to repair the PCB. I remember
having to do this one time, although I had to make my own PCB, using a
different IC, and mounted externally. My effort wasn't wasted, though,
as I treated it as a learning experience.

BTW, over here audio motors typically cost AU$8.65, which is still
cheap.

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
  #24   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Franc Zabkar Franc Zabkar is offline
external usenet poster
 
Posts: 15
Default HELP - Please Identify These Two Parts....................

On Sun, 05 Oct 2008 23:30:36 -0700, Kevin McMurtrie
put finger to keyboard and composed:

In article ,
"Richard Crowley" wrote:

"EADGBE" wrote ...
The anode of the diode is attached directly to three of the resistors
as shown.

I have tried to re-create the circuit board traces on the other side.

The cathode connects to what N_Cook has described as an inductor.

Take a look at this photo:

http://i240.photobucket.com/albums/f...e123/DIODE.jpg

Thanks to everyone for your help so far.

Any chance of finding a replacement for this diode?


Depending on what the actual diagram looks like,
it is quite possibly a simple, generic silicon diode
like a 1N4001 (power rectifier) or maybe even a
popular signal diode like a 1N4148, etc. These
are both very common parts that likely cost only
a few cents in production quantities.


I believe it takes at least two transistors. It's a positive feedback
system to compensate for losses in the motor, creating a virtual perfect
motor that doesn't change speeds under load. And that brings about the
second problem...

The circuit has only one pot so it's not going to work on a worn motor.
The loss compensation is a fixed resistor so it's only good for a motor
in perfect condition.


My understanding is that a real motor can be represented as a perfect
motor with a small series resistance. To maintain a constant speed
under all load conditions, one needs to add an external series
resistor of equal value and then add the voltage drop across this
resistor to the motor voltage.


o---- Rloss ----- perfect motor -----o o--- Rext ---o
|--- voltage at motor terminals ---| |-- loss --|

Here is a circuit I found in "303 Circuits" by Micro-Tech/Elektor
Electronics.

|-------------------------|
| |
| |\ |
| | \ |
|---|- \ | Vm - Im
| \ -----|--- R3 ---|----o o--- MOTOR ---o GND
V1 o--- R1 ---|---|+ / |
| | / |
| |/ |
| |
|------ R2 ----|

Vm = V1 + Im x [(R2/R1) x R3]

Effectively you have a voltage source with a negative output
resistance of R3 x (R2/R1).

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
  #25   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................

On Oct 4, 3:32*am, Reinhard Zwirner wrote:

Obviously, you've forgotten the red connection:

http://www.bilder-hochladen.net/files/12b4-2t-jpg.html


Reinhard:

You are 100 percent correct. My mistake! Thank you for pointing that
out.




  #26   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Franc Zabkar Franc Zabkar is offline
external usenet poster
 
Posts: 15
Default HELP - Please Identify These Two Parts....- The motor itself

On Mon, 6 Oct 2008 06:56:38 -0700 (PDT), EADGBE
put finger to keyboard and composed:

Richard:

Per your request, I have taken a photo of the back of the circuit
board.

http://i240.photobucket.com/albums/f.../CIRCUIT_3.jpg

I have numbered all of the connections so that no one will get
"lost".

They are as follows:

1 - speed control pot connections
2 - 43k resistor
3 - 332 ohm(?) resistor (orange/orange/red?/black/brown)
4 - 421M ohm(?) resistor (yellow/red/orange?/blue/green?)
5 - inductor (olive "resistor" shaped part)
6a - negative lead of 10uF/25v electrolytic
6b - positive lead of 10uF/25v electrolytic
7a - negative lead of 3.3uF/25v electrolytic
7b - positive lead of 3.3uF/25v electrolytic
8 - pink "resistor" (red/red/brown/grey/black)
9 - 22 ohm green resistor (red/red/black/silver)
10a - cathode of black diode (yellow stripe is closest to this
connection)
10b - anode of black diode

The positive and negative power connections are also indicated.

SOME QUICK ADDITIONAL COMMENTS, based on comments I have received so
far....

REMINDER: I know that I could easily get another motor. I AM SIMPLY
TINKERING FOR THE SAKE OF TINKERING, and it's a good opportunity to
learn a bit about this circuit. That's all!

Someone said that they found a substitute for AN6610, but that is NOT
the part number.


Sorry, my mistake.

The burned part says "AN6601". It is made by
Matsu****a (Panasonic). I do indeed have an exact replacement for
this part in hand. I found it online at a supplier specializing in
obsolete semiconductors.

I have tested the motor by running 9 volts directly into it. The
motor runs smoothly and quietly. I will take a current reading, just
to see what I find. But the motor appears to be OK.

I am currently going on the assumption that AN6601 failed on its own
and/or because of the fault of the diode.


This is how I see your circuit:

+ o--------|-----|-----|---------|
12V | | | ___|___
| | | | |
| | | R4 R2 43K
+_|_ | | |_____|
C6 ___ | | | D10
10uF | | | |-------||--- L5 --|-----|
25V | | | | | |
| R8 Motor R3 3K3 +_|_ |
| 220R| | | C7 ___ |
| | | |- VR1 5K 3.3uF | |
| | | |----| 25V | |
| |_____|_________|___________________| |
| | |
| | voltage |
| | feedback |
| AN6601 --------------------------------|
| |
0V 22uH | |
- o-- L9 --|-----------|

AFAICT, the AN6601 IC senses the motor voltage via the potential
divider consisting of VR1, R2, R3, and R4. I suspect that if this
voltage begins to increase, then D10 conducts, causing the voltage at
the AN6601's control pin to rise with respect to its supply pin, thus
turning off the AN6601 and reducing the motor current.

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
  #27   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Eeyore Eeyore is offline
external usenet poster
 
Posts: 8,474
Default HELP - Please Identify These Two Parts....................



EADGBE wrote:

I have a "rainy afternoon project" that has got me puzzled.

I have an old Pioneer cassette deck that I am restoring.

The capstan motor worked for a short while, then it stopped.

The casing of the motor felt VERY warm, so I knew something was
amiss.

(One of the voltage regulators in the deck's main power supply became
EXTREMELY hot whenever the capstan motor was connected, which was
another clue).

Suspecting a short in the capstan motor, I took the motor apart.

Take a look at what I found when I examined the motor's internal
voltage regulator circuit board...

http://i240.photobucket.com/albums/f...3/SCORCHED.jpg

The motor's voltage regulator had burned itself up. Look at how
scorched the circuit board is!

I have a replacement regulator, but I want to make sure that all is
well inside this circuit before installing the replacement. (Yes, I
KNOW that I could simply get another motor, but remember, I am
tinkering for the sake of tinkering!)

So I have been checking all of the other components in this circuit,
to verify their health.

The one component that has me puzzled is the small black "diode"
indicated at the bottom of the photo.

There is no mark on this component other than the yellow stripe you
see.

I cannot get any type of reading on this component when I use my
multimeter -- I get nothing using my diode check function (forward or
reverse bias), no continuity, no resistance reading. It must be
faulty, I am assuming.


Then you're somewhat stuffed without a schematic I'm afraid. Unless you
can reverse engineer the circuit ! I've just been through a similar
problem myself where the parts list had everything on it except RESISTOR
values ! what IDIOT was responsible for that I hate to think.

For any AUDIO people listening, that company was MIDAS btw. I've been in
contact with them for about 2 weeks now about it and all they did was to
re-send the same list in a different file size with the resistor values
STILL missing.


The other component that has me puzzled is the olive green "resistor"
just above the larger blue electrolytic capacitor. I get a steady
resistance reading of .5 ohms on this component.


Plausible. Low value Rs aren't always marked conventionally. Most likely a
current sense R.

Graham

  #28   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Eeyore Eeyore is offline
external usenet poster
 
Posts: 8,474
Default HELP - Please Identify These Two Parts....................



N_Cook wrote:

Is the diode oriented to soak up back emfs from the motor ?
The green thing is an inductor


Both very plausible.

Graham

  #29   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Eeyore Eeyore is offline
external usenet poster
 
Posts: 8,474
Default HELP - Please Identify These Two Parts....................



Jamie wrote:

that diode is suppose to go across the motor leads to suppress back
EMF which can damage components..
It would be a simply low current SI diode.


In which case putting in something bigger like a 1N400x ot UF400x if it has
to be a fast device would do no harm.

I've known 'back emf diodes' like the 1N4148 to be 'killed' by even modest
size relays. I never 'cut corners' on that component any more. 1N400x every
time.

Graham

  #30   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Eeyore Eeyore is offline
external usenet poster
 
Posts: 8,474
Default HELP - Please Identify These Two Parts....................



EADGBE wrote:

The anode of the diode is attached directly to three of the resistors
as shown.

I have tried to re-create the circuit board traces on the other side.

The cathode connects to what N_Cook has described as an inductor.

Take a look at this photo:

http://i240.photobucket.com/albums/f...e123/DIODE.jpg

Thanks to everyone for your help so far.


Can you not trace out the whole circuit ? There's precious little there.

Graham



  #31   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Eeyore Eeyore is offline
external usenet poster
 
Posts: 8,474
Default HELP - Please Identify These Two Parts....................



EADGBE wrote:

Actually, I'll do just a bit better.

Here are ALL of the circuit board traces, done as best as I can. Let
me know if the traces aren't clear enough:

http://i240.photobucket.com/albums/f...23/CIRCUIT.jpg

By the way, the AN6601 laid flat against the circuit board, with the
label side DOWN.


Oh, go on, draw a schematic !

BTW, that black electrolytic may well have had a good cooking. I'd
replace that too.

Graham


  #32   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................

Well, it has all become academic at this point.

I ran the motor off of a 9v battery while it was hooked up to my
multimeter's current setting.

The motor was pulling just over ONE AMP of current!

I took apart the casing and studied everything....sure enough, one of
the armature windings has a scorched spot.

This motor has gone to that Great Cassette Deck in the Sky....
  #33   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Richard Crowley Richard Crowley is offline
external usenet poster
 
Posts: 4,172
Default HELP - Please Identify These Two Parts....................

"EADGBE" wrote...
Well, it has all become academic at this point.

I ran the motor off of a 9v battery while it was hooked up to my
multimeter's current setting.

The motor was pulling just over ONE AMP of current!

I took apart the casing and studied everything....sure enough, one of
the armature windings has a scorched spot.

This motor has gone to that Great Cassette Deck in the Sky....


You could have re-wound the motor! :-)


  #34   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
EADGBE EADGBE is offline
external usenet poster
 
Posts: 229
Default HELP - Please Identify These Two Parts....................

On Oct 7, 2:14*pm, "Richard Crowley" wrote:

You could have re-wound the motor! *:-)


Yeah, I know...but I'm just too lazy! :-)

  #35   Report Post  
Posted to sci.electronics.repair,rec.audio.tech
Mark D. Zacharias[_3_] Mark D. Zacharias[_3_] is offline
external usenet poster
 
Posts: 23
Default HELP - Please Identify These Two Parts....................


"EADGBE" wrote in message
...
On Oct 7, 2:14 pm, "Richard Crowley" wrote:

You could have re-wound the motor! :-)


Yeah, I know...but I'm just too lazy! :-)


There are replacement motors available from MCM and the like...

12V CCW, 12VCW, etc.

Standard mounting holes.

Usually pretty easy to wire in place of the original.


Mark Z.


Reply
Thread Tools
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
can anyone identify this mic? Pea Hicks Pro Audio 7 September 25th 07 07:02 PM
Can anyone identify these noises? Dish Guy Tech 0 January 1st 07 05:22 PM
Please identify these pcb materials John Fields Vacuum Tubes 0 December 29th 06 05:27 PM
CAN ANYONE IDENTIFY THIS MIC David Kakon Pro Audio 13 December 13th 03 05:22 AM
Help Identify this RF sub... sanitarium Car Audio 5 December 3rd 03 05:10 PM


All times are GMT +1. The time now is 08:14 PM.

Powered by: vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AudioBanter.com.
The comments are property of their posters.
 

About Us

"It's about Audio and hi-fi"