Home |
Search |
Today's Posts |
#1
|
|||
|
|||
2 way passive crossover?
Hey all.
Its been about 10+ years since I've messed with a passive installation of subs, mids and high pass drivers. A friend of mine has a single two channel G&S amplifier, 4 8" Rockford subs (brand new) and MB Quart 6" midbass drivers with 1" highpass drivers. Ive been looking for a 2-Way passive crossover that would cut the subs at 100-120hz @ 12db but so far all the two way crossovers ive found only cross the midpass and highpass drivers. Back in my car installation days driving subs at full range was a no-no. It seems as though when installing subs into a bandpass (not sure of which order) its not only OK but your supposed to drive subs at full range?? I dont really fell like building a bandpass though. I really wanted to build a single chamber ported box. Anyway, my best case cenario would be to find a two way passive crossover for this guys install. Cross the lowpass @ 100 or so and the rest from there would go to the mid and highpass drivers. I guess I can build the damn things out of Bass coils and caps but thats another project! Any help would be great. BTW, Im not interested in telling him to "buy a new amp". Its not going to happen. Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#2
|
|||
|
|||
2 way passive crossover?
How about wiring the component set directly to the amp and using a dedicated
subwoofer filter for the subs? This way you save the unnecessary cost of a two-way crossover. Have a listen and if you don't like the way things are, then switch to the crossover set-up later. If you are having trouble finding a crossover (or sub filter for that matter) most car audio shops can sell you the required parts for your particular load impedance. Kevin Murray "Matt" wrote in message ... Hey all. Its been about 10+ years since I've messed with a passive installation of subs, mids and high pass drivers. A friend of mine has a single two channel G&S amplifier, 4 8" Rockford subs (brand new) and MB Quart 6" midbass drivers with 1" highpass drivers. Ive been looking for a 2-Way passive crossover that would cut the subs at 100-120hz @ 12db but so far all the two way crossovers ive found only cross the midpass and highpass drivers. Back in my car installation days driving subs at full range was a no-no. It seems as though when installing subs into a bandpass (not sure of which order) its not only OK but your supposed to drive subs at full range?? I dont really fell like building a bandpass though. I really wanted to build a single chamber ported box. Anyway, my best case cenario would be to find a two way passive crossover for this guys install. Cross the lowpass @ 100 or so and the rest from there would go to the mid and highpass drivers. I guess I can build the damn things out of Bass coils and caps but thats another project! Any help would be great. BTW, Im not interested in telling him to "buy a new amp". Its not going to happen. Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#3
|
|||
|
|||
2 way passive crossover?
How about wiring the component set directly to the amp and using a dedicated
subwoofer filter for the subs? I thought about that too. The only problem I can see is that the crossover that comes with the mid and highpass setup tosses 20-3.5k at the Midbass driver. I dont want that driver to get anything lower then 100 just to keep it from blowing up. The amp the guy has can really pack a punch. It will fry those 6" drivers in no time. Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#4
|
|||
|
|||
2 way passive crossover?
How about wiring the component set directly to the amp and using a
dedicated subwoofer filter for the subs? I thought about that too. The only problem I can see is that the crossover that comes with the mid and highpass setup tosses 20-3.5k at the Midbass driver. I dont want that driver to get anything lower then 100 just to keep it from blowing up. The amp the guy has can really pack a punch. It will fry those 6" drivers in no time. But it's easier (ie. much cheaper) to use a passive high pass for the midbass drivers than a passive low pass for the sub. |
#5
|
|||
|
|||
2 way passive crossover?
Would you be comfortable modifying the midbass section of the crossover to a
bandpass design? The addition of a simple cap would give you a high pass anywhere you want at a 6dB rolloff. 150Hz @ 6dB/octave should suffice to protect the midbasses. Again any installer should be able to help you with this. "Matt" wrote in message ... How about wiring the component set directly to the amp and using a dedicated subwoofer filter for the subs? I thought about that too. The only problem I can see is that the crossover that comes with the mid and highpass setup tosses 20-3.5k at the Midbass driver. I dont want that driver to get anything lower then 100 just to keep it from blowing up. The amp the guy has can really pack a punch. It will fry those 6" drivers in no time. Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#6
|
|||
|
|||
2 way passive crossover?
Not sure what you're getting at Mark. Unless he decides to drive the separates
with deck power he will need a passive filter for the sub. I believe he intends to full-range the amp and do all his filtering afterwards. "MZ" wrote: snip But it's easier (ie. much cheaper) to use a passive high pass for the midbass drivers than a passive low pass for the sub. |
#7
|
|||
|
|||
2 way passive crossover?
Not sure what you're getting at Mark. Unless he decides to drive the
separates with deck power he will need a passive filter for the sub. I believe he intends to full-range the amp and do all his filtering afterwards. Yeah, I just reread that and figured out what he's trying to do. The easiest, best, and cheapest option is to do something he already said he wouldn't do. |
#8
|
|||
|
|||
2 way passive crossover?
Would you be comfortable modifying the midbass section of the crossover to
a bandpass design? The addition of a simple cap would give you a high pass anywhere you want at a 6dB rolloff. 150Hz @ 6dB/octave should suffice to protect the midbasses. Again any installer should be able to help you with this. "Should" being the operative word... |
#9
|
|||
|
|||
2 way passive crossover?
Would you be comfortable modifying the midbass section of the crossover to
a bandpass design? The addition of a simple cap would give you a high pass anywhere you want at a 6dB rolloff. 150Hz @ 6dB/octave should suffice to protect the midbasses. Again any installer should be able to help you with this. "Should" being the operative word... Maybe Im not asking the question right. I want the midpass to start around 100-120hz. I was also asking if I should (or can) drive the subs at full range. I'd be cool with running a 2-way crossover that would output 130 and below to the sub and 120 and above to the Mid/highpass and just put caps and coils on the tweets to cross them at 3500 or something. I used to be able to buy boards with the caps and coils on them that did just that. All I can find now are 2 way crossovers for Mids and highs. Like I said, in my installing days we would have put a 100mf cap on the midbass, a 5.6 or 6.1mh coil on the subs and called it quits. If we wanted to get fancy we might even add the extra parts to the crossovers to make them 12db per octave but 6 worked fine. The last time I worked "professionally" in a car stereo shop Linear (sp?) was still around, Rockford was JUST getting into MOSFET and Orion was the mac-daaddy of power. see, its been a while... Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#10
|
|||
|
|||
2 way passive crossover?
Maybe Im not asking the question right.
I want the midpass to start around 100-120hz. I was also asking if I should (or can) drive the subs at full range. I'd be cool with running a 2-way crossover that would output 130 and below to the sub and 120 and above to the Mid/highpass and just put caps and coils on the tweets to cross them at 3500 or something. I used to be able to buy boards with the caps and coils on them that did just that. All I can find now are 2 way crossovers for Mids and highs. Like I said, in my installing days we would have put a 100mf cap on the midbass, a 5.6 or 6.1mh coil on the subs and called it quits. If we wanted to get fancy we might even add the extra parts to the crossovers to make them 12db per octave but 6 worked fine. The last time I worked "professionally" in a car stereo shop Linear (sp?) was still around, Rockford was JUST getting into MOSFET and Orion was the mac-daaddy of power. see, its been a while... It's not generally the best idea to run your sub full-range. But if it's in the trunk, I suppose it could suffice for a simple budget installation. Performance will suffer though, and the amp will run hotter. If you want to determine what size caps and inductors to use, visit passivecrossovers.com. |
#11
|
|||
|
|||
2 way passive crossover?
I think I see what you're asking. "Is it ok to do less than the required minimum
for 'decent' sound?" I assumed in my previous posts that you already had a crossover that came with the component set. I was suggesting that you modify this existing crossover to suit your mid/high needs. If you have no existing crossover for the component set, you will have to build/buy one. I urge you to research crossover design a little more on the site Mark provided. Then you can choose whatever crossover points make you happy. You might be surprised what you can accomplish for little money. Then you have to deal with your sub. If you want to really go cheap with the sub you could try running it full range since it wont cost you a thing. If it's in the trunk, like Mark said, you may get by with that set-up. Worst case you need to add a filter later. I think that if you expect half-way decent sound from your ported box you will have to low-pass filter it. I realise the importance of budget but somewhere you need to make concessions. All that expensive gear will go to waste if you compromise the install for a few dollars. "Matt" wrote in message ... Would you be comfortable modifying the midbass section of the crossover to a bandpass design? The addition of a simple cap would give you a high pass anywhere you want at a 6dB rolloff. 150Hz @ 6dB/octave should suffice to protect the midbasses. Again any installer should be able to help you with this. "Should" being the operative word... Maybe Im not asking the question right. I want the midpass to start around 100-120hz. I was also asking if I should (or can) drive the subs at full range. I'd be cool with running a 2-way crossover that would output 130 and below to the sub and 120 and above to the Mid/highpass and just put caps and coils on the tweets to cross them at 3500 or something. I used to be able to buy boards with the caps and coils on them that did just that. All I can find now are 2 way crossovers for Mids and highs. Like I said, in my installing days we would have put a 100mf cap on the midbass, a 5.6 or 6.1mh coil on the subs and called it quits. If we wanted to get fancy we might even add the extra parts to the crossovers to make them 12db per octave but 6 worked fine. The last time I worked "professionally" in a car stereo shop Linear (sp?) was still around, Rockford was JUST getting into MOSFET and Orion was the mac-daaddy of power. see, its been a while... Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#12
|
|||
|
|||
2 way passive crossover?
I realise the importance of budget but somewhere you need to make
concessions. I never said anything about the install being held back by budget. The guy just wants to use what he has. For the record... 1 G&S P500 (I think thats the model) 1 Kenwood... Blah blah head unit 4 pairs of MB Quart 6" midbass and the tweeters that came with them AND the crossovers that came with them. 4 Rockford SP88's OK, he lost the Bass coils when he tossed the box that the woofers were in. From the looks of crossovers that came with the MB Quarts they dont notch out frequencies below 100hz so that would mean that they were driven at 20hz-whatever they cut at. I dont want to run the subs at full range but read that 7th order bandpasses could get away with this. My absolute BEST case cenario would be to find 2 2way crossovers that did the following... Provide the Subs with 20hz-120hz@12db and 120HZ and above to the Mid/Highpass which I would then run into the MB crossovers. Thanks for all the input! Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#13
|
|||
|
|||
2 way passive crossover?
"Matt" wrote: snip My absolute BEST case cenario would be to find 2 2way crossovers that did the following... Provide the Subs with 20hz-120hz@12db and 120HZ and above to the Mid/Highpass which I would then run into the MB crossovers. You can do this. I don't think there is a pre-fab crossover for your application. Speak with a car audio installer about the parts you need for it. Ask him about a subwoofer filter and perhaps simply modifying the existing MB Quart crossovers to bandpass the midbass (ie:120-3500). There's no need to build another crossover. My understanding was that your friend wanted a "single chamber ported box". I'm not sure how bandpass enclosures apply here. Some people are satisfied with no filter on a bandpass. I find that the highs still escape, with some added reverb. I suppose it would be fine if the box was in a trunk. Hope that clears things up for you. |
#14
|
|||
|
|||
2 way passive crossover?
My understanding was that your friend wanted a "single chamber ported box".
that was just another option knocking around in my head. I had a 7th order bandpass with two JL 10's in it a long time ago. I ran the thing full range and it seemed to be fine. Ive just never been a big fan of running subs at full range. Midrange audio out of a sub sounds REAL bad to me. Almost as bad at those big ole' nasty horn tweeters... thanks for the input! Ill work on modifying the MB crossovers and toss coils on the subs. That sounds like the thing to do. Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#15
|
|||
|
|||
2 way passive crossover?
Matt wrote
that was just another option knocking around in my head. I had a 7th order bandpass with two JL 10's in it a long time ago. I ran the thing full range and it seemed to be fine. Ive just never been a big fan of running subs at full range. Midrange audio out of a sub sounds REAL bad to me. Almost as bad at those big ole' nasty horn tweeters... thanks for the input! Ill work on modifying the MB crossovers and toss coils on the subs. That sounds like the thing to do. Maybe I am oversimplifying this, but can't you just put 100uF caps inline with the existing crossovers to highpass the components? I don't see why the existing crossovers have to be "modified". Also, as far as the subs are concerned, you only need one coil unless you are planning on using more then one channel to run them. The way I see it you need 4 100uF bi-polar caps, and a 6mh coil. Am I wrong? |
#16
|
|||
|
|||
2 way passive crossover?
The way I see it
you need 4 100uF bi-polar caps, and a 6mh coil. Am I wrong? Nope, your right on the money. Ive been having a hell of a time finding them which is why I started this thread. I tried searching for Bass Coil in google. It gave me a few hits but nbothing to obvious. I didnt bother with the caps after my search for the coils failed. If you guys could point me to an online source that would be great. The few car stereo stors Ive tried in my area didnt have the stuff. One even asked me what a bass coil was... eh... Thanks! Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#17
|
|||
|
|||
2 way passive crossover?
|
#19
|
|||
|
|||
2 way passive crossover?
"Daniel Snooks" wrote: snip Maybe I am oversimplifying this, but can't you just put 100uF caps inline with the existing crossovers to highpass the components? I don't see why the existing crossovers have to be "modified". Also, as far as the subs are concerned, you only need one coil unless you are planning on using more then one channel to run them. The way I see it you need 4 100uF bi-polar caps, and a 6mh coil. Am I wrong? Essentially what I was saying. I'd prefer to add the cap to the existing crossovers to keep things clean and make troubleshooting easier should checking connections become necessary. I'd personally go with a higher order, like 12dB which would make things a little messier otherwise. I'm not going to check your math on the component values but it sounds ballpark. I have access to lots of free motor wire so I like to wind my own coils. I wanted to suggest that anyone should research doing things themselves in case they too can save some money on their install. It adds a bit more of the pride factor too. |
#20
|
|||
|
|||
2 way passive crossover?
Here's the link to the PartsExpress part.
BINGO! Thats exactly what I needed. Thank you very much! Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
#21
|
|||
|
|||
2 way passive crossover?
This place has up to 5mH...
They have even larger if you're willing to pay the extra dough. http://www.speakercity.com/xover/coils.shtml -- Mark remove "remove" and "spam" to reply "Matt" wrote in message ... Here's the link to the PartsExpress part. BINGO! Thats exactly what I needed. Thank you very much! Matt M and M Electronics 6661 Stanford Ranch Road Suite F, PMB 105 Rocklin Ca 95677 916-275-5871 |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
rec.audio.car FAQ (Part 4/5) | Car Audio | |||
rec.audio.car FAQ (Part 2/5) | Car Audio | |||
Dyns in doors | Car Audio | |||
simple crossover question | General | |||
HELP !!! | Car Audio |