Home |
Search |
Today's Posts |
#41
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
wrote in message
On Jul 8, 2:17 pm, Bret L wrote: A Mustang took about the same materials cost and about half the manufacturing labor to build as did a Spitfire. Arguably the Spitfire was prettier. It's worth reading Len Deighton's novel "Fighter," in which he goes into the different manufacturing costs in detail. He laments the phasing out of the Republic P47 in favor of the very much cheaper Mustang, which had a significantly worse record of killing pilots in accidents. A ludicrous comparison given all of the other differences that were involved. Note the absence of any kind of fair comparison and no relevent statisics from an independent source. It would appear that Mr. Atkinson has now taken his inability to do fair comparisons of audio equipment to the air. :-( |
#42
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
John Byrns wrote: In article , Patrick Turner wrote: Bret L wrote: This month marks, approximately, the 60th anniversary of the Williamson amplifier in the United States. It was first described in Wireless World magazine in the UK in 1947, but little notice was taken at first by the American hobbyist-or professional. However, requests by amateurs and pros alike for a factory wound variant of the output transformer described in the article eventually provoked the American transformer companies to make a suitable unit, with American style 16/8/4 ohm output taps rather than the British style of multiple series parallel jumpers, and soon the various poopular magazines were covering the US versions, each magazine promoting one or another variant according to, one suspects, which transformer company advertised the most in that magazine. Yeah, the american makers' response to Willy's ideas was "how do we dumb down this too-hard-to-wind tranny and make a profit?" Looked to me like the British amp makers had pretty much the same attitude. The Williamson was a revolution more in thought than in initial results. American ' fidelity nuts' were building prewar designs without feedback, primarily, and with triodes of low amplification factor. Like the first F1 Lotus race car entered at Indianapolis, it made a mediocre showing-but how it did it precipitated a technical revolution. The Williamson did away with coupling transformers and was built from low cost parts, save only the output transformer. It needed no bias supply which then meant batteries or a tube rectified affair necessitating a protection relay. Protection relay? With bias supplied by batteries or tube rectifiers as specified above a protection relay is almost a necessity. I've never seen a mass made tube amp with batteries for bias. Batteries go flat or leak all over the place and cost more than other means of biasing, so no batteries were ever approved by the company bean counter. I never seen any mass made tube amp with a with any active protection whatsovever. "mass made" amplifiers for home use mostly used selenium bias rectifiers which were relatively reliable eliminating the need for a protection relay. You will find protection relays used in some higher power audio amplifiers designed for commercial and industrial applications, especially those using vacuum tube bias rectifiers. Sure, selenium rectifiers were used *when* they became supposedly more reliable than a tube rectifier. They saw service in radios first. But all the tube amps mass made in the past used tube diodes. And for the bias. As soon as the **silicon** rectifier with a high reverse peak voltage rating became available then the tube rectifiers were retired immediately. And in amps by McIntosh, they immediately used a voltage double type of supply because the Si diodes still gave bettwr regulation than the full wave with CT winding and two diodes. And the voltage doubler needed 1/4 of the transformer turns using much thicker wire so the PT became cheaper. The bean counters had a party the day Si diodes were found to be reliable. But of course there was still never any active protection in mass made amps. And with Si rectifiers, when a tube begins to die by conducting much more Idc than usual, the Idc increase isn't enough to make a fuse blow at first because invariably high value caps and high fuse values have been used withthe Si diodes. Maybe a OPT primary winding begins to cook causing a shorted turn, so when an owner plugs in a new tube later he finds the music is bleedin awful, so he's up for a big repair bill. Active sensing of cathode current would have saved the owner from such dreadful pain, but in a stereo amp with 4 output tubes you'd need 4 diodes and some sort of device which **latches** on to turn off the amp. Afaik, there was no cheap easy way this could be done in 1955. Latching relays with a botton to unlatch them may have been devised, and maybe you could use a tube as the turn on element to work the relay from a bias supply, or B+ perhaps. Today I use sensitive gate SCR, C106D, and 4 x Si diodes and a relay operating off a 12V auxilliary. Its very cheap and has saved the bacon many times.... Patrick Turner. -- Regards, John Byrns Surf my web pages at, http://fmamradios.com/ |
#43
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
Bret L wrote:
On Jul 7, 11:29 pm, keithr wrote: Andre Jute wrote: On Jul 8, 12:13 am, wrote: On Jul 7, 6:39 pm, Andre Jute wrote: Ludwig claims among other inanities that Ferrari engines are copies of Packard engines. Ditto for the Merlin engine; Merlin was a Rolls-Royce design... Yes it was, based on the Schneider Cup-winning engine. But RR did eventually license the Merlin to Packard, who manufactured the engine to power the P51 Mustang. John Atkinson Editor, Stereophile Yes, I know all that, John. But that Rolls-Royce licensed the engine to Packard doesn't make it a "Packard design" as Ludwig tries to claim; it remains forever a Rolls-Royce design. Ludwig, besides making rather large claims of this ludicrous nature, is a copyright thief who in the past has claimed that my copyright material belonged to him by right of repeated theft. He is a perfect stranger to logic. Andre Jute Visit Andre's books at http://www.audio-talk.co.uk/fiultra/THE%20WRITER'S%20HOUSE.html The P51 was originally developed to an RAF requirement. It was fitted with a Packard engine which gave so-so performance especially at high altitude. No, it was an Allison. Sorry, you are correct, somehow I got Packards on the brain, and of course it was Allison who went on to build the copy Merlins The Allison had a much simpler supercharger, because it was intended to be used in conjunction with a turbo. The ONLY advantage RR had over Allison was a more sophisticated two stage two speed supercharger. RR doctrine was that turbos were bad because the energy they used was better employed as thrust from the engine gases. While they did get some thrust recovery, Looking at the Spit's exhausts, I would seriously doubt that they got much the P-51 got even more thrust from the radiator heat. OTOH the Mustang suffered what was then a total loss damage from being landed gear up whereas the Spitfire was flying (albeit with a different engine and prop) the next day. Yes the P-51 was probably the most famous exponent of the Meredith effect but it was hardly the only one. The BF-109 also used the effect, and even the Spit's radiator would have given some effect. Then, of course there is the claim that radial engines utilised the effect even more than the P-51 A Mustang took about the same materials cost and about half the manufacturing labor to build as did a Spitfire. Arguably the Spitfire was prettier. It was also a significantly earlier design. |
#44
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
Bret L wrote:
On Jul 8, 7:10 am, "Arny Krueger" wrote: "Bret L" wrote in message On Jul 7, 6:36 pm, Andre Jute wrote: On Jul 8, 12:13 am, wrote: On Jul 7, 6:39 pm, Andre Jute wrote: Ludwig claims among other inanities that Ferrari engines are copies of Packard engines. Ditto for the Merlin engine; Merlin was a Rolls-Royce design... Yes it was, based on the Schneider Cup-winning engine. But RR did eventually license the Merlin to Packard, who manufactured the engine to power the P51 Mustang. John Atkinson Editor, Stereophile Yes, I know all that, John. But that Rolls-Royce licensed the engine to Packard doesn't make it a "Packard design" as Ludwig tries to claim; it remains forever a Rolls-Royce design. Ludwig, besides making rather large claims of this ludicrous nature, is a copyright thief who in the past has claimed that my copyright material belonged to him by right of repeated theft. He is a perfect stranger to logic. Packard took the basic design and reengineered the whole thing from a tooling and construction standpoint, and made many things interchangeable that had been fit-on-assembly previously. They made their own patterns and core boxes from scratch and changed materials and harmonized many dimensions. What had taken dozens of fitters days to tweak and cobble now went together in minutes without stoning or filing. In the field it meant that individual parts could be swapped where before RR had had complete assemblies rotated and shipped to depots. My father was part of the Packard effort to reproduce the Rolls-Royce Merlin engine in the US. His accounts of how it was done agree with Mr. Ludwig's statements, above. They started with RR blue prints of just the engine, and re-engineered the design, tolerances and production methods in accordance with U.S engineering practice, which was more advanced when it came to volume production of precision engines. Packard was a first rate company with a superior engineering nd manufacturing force. And the Merlin effort was really their finest hour, because it's harder to do that with someone else's design than to design your own in most cases. RR was also first rate, but volume production was not their thing at all. The figures are, I believe: Rolls Royce: 82117 Ford (UK): 30478 Packard: 55523 |
#45
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 8, 5:29 am, keithr wrote:
Andre Jute wrote: On Jul 8, 12:13 am, wrote: On Jul 7, 6:39 pm, Andre Jute wrote: Ludwig claims among other inanities that Ferrari engines are copies of Packard engines. Ditto for the Merlin engine; Merlin was a Rolls-Royce design... Yes it was, based on the Schneider Cup-winning engine. But RR did eventually license the Merlin to Packard, who manufactured the engine to power the P51 Mustang. John Atkinson Editor, Stereophile Yes, I know all that, John. But that Rolls-Royce licensed the engine to Packard doesn't make it a "Packard design" as Ludwig tries to claim; it remains forever a Rolls-Royce design. Ludwig, besides making rather large claims of this ludicrous nature, is a copyright thief who in the past has claimed that my copyright material belonged to him by right of repeated theft. He is a perfect stranger to logic. Andre Jute Visit Andre's books at http://www.audio-talk.co.uk/fiultra/THE%20WRITER'S%20HOUSE.html The P51 was originally developed to an RAF requirement. It was fitted with a Packard engine which gave so-so performance especially at high altitude. That was an Allison engine and the only reason it gave so-so performance is that it was fitted without the forced induction for which it had been designed. I had some of those Allison 1710 for power boat racing and, used as intended by the designers, they were superb, virtually indestructible engines. But then I generally like honest, sturdy American engines more than their perhaps better bred European counterparts, which are often too tricky for their own good. (Yeah, I know, it sounds hypocritical, all those old Bentley chassis I tuned into sports cars, the years of driving European cars. But, honestly, one of my favourite touring cars of all time was the mid-60s Ford LTD, same as the execrable Ludwig has just bought, and one of my favourite fast cross-continental wheels was the Australian Ford GTHO, which was an American Falcon hotrodded by Ford's Australian branch office.) The British fitted a Merlin in place of the Packard and immediately got another 50mph out of it and improved high altitude performance. Later, when the USAAF ordered the P51, Packard licenced the Merlin from Rolls Royce and this engine was fitted to all subsequent models. The genesis of the P51 is an interesting example of American can-do -- count the number of days between the British asking whether the Americans could build the Corsair and the Americans saying no, we can design a better plane, and the day the first prototype P51 flew. Andre Jute Visit Jute on Amps at http://www.audio-talk.co.uk/fiultra/ "wonderfully well written and reasoned information for the tube audio constructor" John Broskie TubeCAD & GlassWare "an unbelievably comprehensive web site containing vital gems of wisdom" Stuart Perry Hi-Fi News & Record Review |
#46
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
Bret L wrote: The Williamson was a revolution more in thought than in initial results. American ' fidelity nuts' were building prewar designs without feedback, primarily, and with triodes of low amplification factor. Like the first F1 Lotus race car entered at Indianapolis, it made a mediocre showing-but how it did it precipitated a technical revolution. The Williamson did away with coupling transformers and was built from low cost parts, save only the output transformer. It needed no bias supply which then meant batteries or a tube rectified affair necessitating a protection relay. Protection relay? I never seen any mass made tube amp with a with any active protection whatsovever. The old theater amps that were fixed bias in the 40s had them. The audio industry attitude has been and continues to be, "let the punters blow up their amps soon so they will buy another." You'd think someone would have invented a nice little circuit using one IC would indicate if the load value fell below 2 ohms even for an instant and then turn off the amp completely until somone fixes the shorted speaker or lead or other problem. Since Americans generally did not entertain winding their own output transformers, soon a race was on amongst the manufacturers to make a more and more suitable unit, and each purported to supply some extra, magic mojo with their unit. More relevantly, many had various taps on the secondary not originally intended for ultra-linear operation, but suitable for it, and soon many Williamsons were operating ultralinear and with a considerably lower plate load and a beefier power supply, upping power output in true Yankee mechanic fashion. More power, more distortion, and generally worse performance in high class AB with a low class A % were the way the americans travelled. You couldn't sell low powered amps to the yanks. It was no use trying to sell a Morris car to a yank. As I write this there is a 50s or 60s Morris Minor, right hand drive, parked in the parking lot outside the window. Next to it is the owner's wife's Chevy powered XJ12. What are the ODDS? The downstairs office is owned by an old Brit car freak. On the other side of the lot is a new Smart car, about the size of a golf cart. I just bought a 68 Ford LTD, four door, with a fresh EFI five liter and AOD. That's my idea of a good car. Gas is the cheapest thing I put in it. Yanks liked everything big and preferebly huge, and certainly bigger than their frinds. The Williamson had many flaws, seen from today's perspective. For its weight and build cost its power output is unimpressive, and it trades low distortion for stability. It is not unconditionally stable and indeed often went into oscillation with electrostatic speakers. Being cathode biased, it has a relatively high quiescent power draw. Like a Ferrari with a Lampredi long block V12 or a Westland Lysander, its ills are fixable but at the cost of its basic nature. A stable fixed- bias Williamson is hardly a Williamson, and a Lysander with a P&W under the cowl loses part of its essential charm, as does a Superamerica with a Columbo short block V12 or a Lampredi with its water pump cavity blocked off and a Chrysler unit in a Porchev housing glommed off to the side. By 1955, the British were no longer competitive in the high fidelity amplifier business in terms of metrics: the Radford and Kerr-McCosh had no serious market share at home and none abroad. Marantz, McIntosh, and Harmon Kardon totally dominated the high end and Dyna the low, with Fisher and Scott offering consumer friendly upscale units for the mainstream buyer. The Germans, the Dutch (Philips) , the Scandinavians and of course the rest of the Anglosphere never even got to the starting gate. It wasn't until the solid state era that the US manufacturers lost absolute, unchallenged domination. Ah, you forgot trade tarriffs and import barriers. In Oz, hardly anyone bought anything american because it always was so damned expensive. Ralf Nader pointed out that american motor vehicles were no safer than the ones we made here, albeit under companies run as offshhots to GM in america, such as Holden. Hardly anyone made any money selling Oz made amps to other Oz ppl because those with any money bought british brands such as Leak or Quad. Many audio ppl made their own amps using 807 and 6SN7 from ex-army surplus stores and OPT, PT and chokes from local makers; A&R in Melbourne, Fergeson in Sydney. None were Partridge quality, so the extremely small number of audiophiles in Oz which was a very un-cultured place in 1955 had trouble making stable tube amplifiers of any kind. The Mullard 510 and 520 became more popular than Williamsons. Australia, and New Zealand, DID NOT MATTER, there weren't enough people in those countries and of those that were they were as you say yourself were not willing to pay for the good stuff. in the history of vintage tube audio, only two nations really mattered, although the Germans and the Dutch (Philips) had some interesting stuff, and even the Finns had a really interesting design. German audio was not readily available in the US for various reasons, one of which is that a real cocksucker named Steven Temmer got the Telefunken franchise in the US and ****ed the pro market over hard and fast.. Siemens and Telefunken had some great tech but we never saw it and neither did the Brits AFAIK. It's a real shame as the EL 156 would have let McIntosh build an honest 100+ wpc amp with two tubes essentially in the receiving tube class-no bright filaments, plate caps or really high B +. Again, AUSTRALIA DID NOT MATTER and so far STILL DOES NOT. Not for audio. There is an interesting company making pianos there though. The Williamson was just one of several designs one could build onself, and AFAIK, there was NEVER a perfectly created commercial replica of the Willy circuit including the exact details of the OPT with all its windings which allowed wasteless arrangement of secondaries. Both British and American commercial winders built MUCH BETTER transformers than the Willy paper design. Even backwoods transformer shops realized that much simpler designs could be better. It's possible the Germans made excellent ones too but they did not market them as a standalone product, and no other country mattered. Even Italy, which had something of an electronics industry, wasn't a player. Gee, I thought Australia DID ****IN MATTER A LOT in the bygone days in a different world after 1939 to about now. The US wasn't about to let Oz go to the japs because it had very big business interests here. In fact the US has done well out of Oz, and it wouldn't like to lose it; it'd be like losing a state of the Union. But your'e about right about how US exporters often thought about Oz, too much trouble to export to and not enough sales. Now its very hard to find anything worth buying in the shops with a made in the USA sticker. Maybe its different now. I don't buy much od any damn thing from anyone, so what would I know? But I could buy a Jolida, made by joint venture US-China team. No thankyou, I don't wanna buy one. I seen the re-issue McI amps in the shops here and no thanks, I don't want one. I've repaired too many US mades to ever want one. I see ZERO evidence that any mass made amplifiers included OPT like the one Willy designed. Quad and Leak and Dynaco and all the rest used inferior OPT. Maybe there were better designs available from dedicated tranny makers but their product rarely found their way into anything mass made. There was a local OP tranny winding industry in Oz many years ago and you could always buy a pair of good OPT off the shelf for a home amp but that all died in about 1965. The top range of OPT from locals Fergeson and A&R were very good, but hardly anyone bought them; the market was microscopic, and those that bought for their home amps were mainly poor, and too poor to afford the best. Needless to say the local products were much cheaper than anything imported from the US or Europe, UK. No freight costs either. In 1955, you could always have had your amplifiers hand made by someone just like how people have their amps made by coming to me and ordering one. The hand made amps comprise about 0.00000000000000000000000000000000000001% of the total amp market. Nobody remembers the hand makers of 1955, and they won't remember me when I'm gone. One could say the McIntosh OPT was a masterpiece, but I wouldn't. Its just one hellova complex design. GE put out a book on 17 amp designs form 5 to 1,100W and in the book they describe good techniques for minimising leakage inductance with shunt capacitance so there was no need for bifilar or trifilar windings. The McI OPT has wires wound close with 470V voltage difference. Anyway, there are easier ways to get the same result, and you don't have the Pd between adjacent turns, so the alternative to McI is better. Williamson started a ball rolling though and made ppl aware of the benefits of wide OPT bandwidth, and made then aware of how to get those benefits. Every other maker kept their fukkin secrets mainly to themselves. I find it very easy to make an OPT give Fsat at 15Hz at full PO and 200kHz of HF. You just use lots of interleaving. You keep the insulation thickness between P and S rather high, you use many more turns per volt than everyone else does except Williamson, and you use far more Afe than anyone else, and losses are then below 5%. A lot of my website deals with OPT BW, and OPT losses and how to optimise designs. I merely carry the torch further for luminaries like Williamson and Baxandal. Patrick Turner. |
#47
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 9, 10:40*am, "Arny Krueger" wrote:
wrote in message On Jul 8, 2:17 pm, Bret L wrote: A Mustang took about the same materials cost and about half the manufacturing labor to build as did a Spitfire. Arguably the Spitfire was prettier. It's worth reading Len Deighton's novel "Fighter," in which he goes into the different manufacturing costs in detail. He laments the phasing out of the Republic P47 in favor of the very much cheaper Mustang, which had a significantly worse record of killing pilots in accidents. A ludicrous comparison given all of the other differences that were involved. Note the absence of any kind of fair comparison and no relevent statisics from an independent source. What are "statisics", Arny. Do you mean "statistics"? As for Len Deighton, who used to live down the road here on the Carbery Coast, he leaves you for dead as a researcher, but then everyone does. However, in this case it is particularly stupid of you to spout your usual spite, Krueger, because Deighton is known world- wide to be an extremely thorough and detailed researcher of military history, a widely admired writer of both fiction and non-fiction on the subject. It would appear that Mr. Atkinson has now taken his inability to do fair comparisons of audio equipment to the air. :-( It is obvious that Arny Krueger, as usual, has an unhealthy obsession with someone who once put him down spectacularly, and in public, and at Mr Krueger's own masochistic invitation. Andre Jute Independent observer |
#48
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 9, 5:40*am, "Arny Krueger" wrote:
wrote in message On Jul 8, 2:17 pm, Bret L wrote: A Mustang took about the same materials cost and about half the manufacturing labor to build as did a Spitfire. Arguably the Spitfire was prettier. It's worth reading Len Deighton's novel "Fighter," in which he goes into the different manufacturing costs in detail. He laments the phasing out of the Republic P47 in favor of the very much cheaper Mustang, which had a significantly worse record of killing pilots in accidents. A ludicrous comparison given all of the other differences that were involved. The comparison is valid given that the prime role for both designs was the long-range escort for the 8th Air Force daylight bombing missions to Germany. Note the absence of any kind of fair comparison and no relevent [sic] statisics from an independent source. I referred to Len Deighton's comments, in his novel "Fighter," which , like the companion "Bomber," includes a great deal of factual information. I would have thought that Deighton _was_ an "independent source." John Atkinson Editor, Stereophile |
#49
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
Alex wrote: "Patrick Turner" wrote in message ... Nearly all the people I ever knew in the 1950s might have had a very crummy radiogram with a lone 6V6 output tube. We rolled on the floor laughing at the Goon Show, and nobody cared a hoot about hi-fi. There was 4 kHz of BW, and the people on radio or those who sang had voices which could be easily understood. No we have hi-fi gear to reproduce the most appalling speaking or singing voices and much noise masquerading as music. While most of the world gladly got rid of these early horrid "lounge-room entertainment gadgets", when TV came in here in 1956, audio went even further out of people's minds, and when everything went solid state it got even worse, until the laws on import duties were changed to allow foreign products in from mainly Japan. I am not an expert in the tube amps, but closely observe vintage Oz radios for sale on the e-bay. I found that the Oz radios from 30's to early 60's are extremely primitive and electrically boooooooooooooooring. 6A8G-6U7G-6B8G-6V6G-5Y3 , then 6AN7A-6N8-6N8-6M5-6X4 and later 6BE6-6BA6-6AV6-6AQ5-6X4 was pretty much the limit of imagination of Oz engineers. Almost none of the Oz radios have a tuning indicator, very few have an RF stage (6-th valve). Wiring is messy, STC and Kriesler are the messiest ones. I agree entirely, but the makers were mainly dealing with poor people. But deluxe radios were made with the above tube line ups but with tuning indicators and better speakers and cabinets. These comprised a small % of sales, and are the most collectable. In East Germany, there was a Trabant motor car. The car for poor folks made by poor folks. But the Grundig radios from West Germany also were very messy. also very pricey. In comparison, even Russian radios (I am a Russian) of that era were more advanced. Almost all models had a 6E5G magic eye, 30% of radios had 6L6GT SE output (5W), some had push-pull ultralinear 2x6L6 stages. Yes, but the tube radios for Russia were made by a centralist communist government who wanted its people to hear the socialist propaganda. The people of Russia paid dearly indirectly for the radio experience. Here we had makers having to make a profit, and compete againsteach other and imports. But we got piles of propaganda too that the bosses of industry all wanted us to hear. It was incessant and infuriatingly boring advertising, with the most stupid brainless pop music played between advertisements. Those would have a separate bass/treble tone control and a dedicated 6SJ7 1-st audio stage, as well as variable IF bandwidth for distant/local reception. Output transformers were on average twice heavier than in Oz. Primary resistance did not normally exceed 250 Ohm with 15...20H, while in Oz radios 350...500 ohm and 8...10H was a norm. (What bass response can be expected from those undernourished trannies?) Ceramic trimcaps were used, not the wirewound rubbish common in OZ radios. Yes, you may well wax lyrical about the wonders of Russian radios. if you wanted deluxe in Oz, you could have deluxe, you just paid through the nose. The top range Radiola AM radios include all the features of the best Russian radios. But of course we didn't get FM here until about 1972, and we never had long wave, so our radios were nice and simple and easy to fix when they broke. Ever tried servicing a big old Grundig with FM and long wave? Its a damned nightmare. When FM finally got here, it was all mainly done by the cheap Japanese tuners full of chips fior hi-fi, and with an am section that was lousy, and had only 3 tiny bjts. The whole Oz radio and TV industry was basically abolished in favour of imports. I don't recall ever seeing one single Russian import though. Maybe mainly everyone in Russia DID NOT have a really nice radio, unless you were maybe a very good comrade and a member of the Party. Maybe not enough radios were made in Russia to have enough to export either. There was once the Communist Party of Australia. Members went to Russia on visits to see how the paradise of socialists operated. They came back rather dismayed. Then hardly anyone voted for them at Oz elections. They opposed cheap imports because it cost the jobs of Oz workers. They believed in a Utopia that was always going to remain a dream. The "commos" as we called them were pretty tame though, and harmless. They drank and ****ed each other's wives a bit too much, and talked a lotta bull**** but we didn't line them up to be shot. We knew the value of tolerance and democracy. Quite a few got into trade union rep positions and caused mahem, but at least they had the guts to take on the real arsoles of big business. Someone had to do it and fight for the workers rights and wages. I'm glad we had commos. Nothing like societal diversity to maintain a balance. And without too many pools of blood and screams late at night. But the workers mainly preferred the cheap Japanese products, and left wing socialists had to accept the fact that workers wanted cheap goods and would pay for them willingly despite the result of putting local comrades out of a job, and keeping asian workers enslaved. OK, you loose a job. So damn what. You get another. You stop winding Kriesler OPTs one day and go down the road to wind power trannies for Water Authority control units. In 1960, if you couldn't get a job you had to be deaf, dumb, and blind. In the 1950s and 60s Oz had exremely low unemployment rates. And if a man wanted to he could change jobs 4 times a year. If he didn't smoke or drink, and didn't have too many roots and father too many kids, he could live like a king with the best of radios. He could buy a house at a reasonable price and support his dependant wife and pay off the house on a bricklayers wage, or a transformer winder's wage which were about the same money. His life under capitalism offered far better quality than in Russia, the UK, Germany, and most othere nations. The doctors and dentists were lousy and expensive though. Life expectancy was much lower than now. Now ppl's houses are full of asian made gadgets. It always takes 2 wages to survive and buy a house. And just as well there is the Pill because ppl can't afford to have more than 1.4 children, and they can't start breeding until 30+. Somewhere amoungst their pile of domestic crap there might be a radio, but radio listening is likely to soon become extinct. Don't ask me how a digital radio works. Don't ask me to service one. I am pig ignorant. Patrick Turner. Regards, Alex |
#50
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 9, 11:39*am, keithr wrote:
Bret L wrote: RR was also first rate, but volume production was not their thing at all. The figures are, I believe: Rolls Royce: 82117 Ford (UK): * 30478 Packard: * * 55523 I would normally say you lost the point 86 to 82, Keith, on the assumption that if the fiercely protective Rolls-Royce produced less than half of total production of their own design, then it should be clear that "volume production was not their thing at all". But in wartime, any port in a storm, the rules change. It seems to me that if under such huge pressure RR still produced half of all engines made to that design, they had the production down pretty much pat. Andre Jute Plain common sense costs nothing except application |
#51
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"sortech" wrote in message ... Alex wrote: "Patrick Turner" wrote in message ... Nearly all the people I ever knew in the 1950s might have had a very crummy radiogram with a lone 6V6 output tube. We rolled on the floor laughing at the Goon Show, and nobody cared a hoot about hi-fi. There was 4 kHz of BW, and the people on radio or those who sang had voices which could be easily understood. No we have hi-fi gear to reproduce the most appalling speaking or singing voices and much noise masquerading as music. While most of the world gladly got rid of these early horrid "lounge-room entertainment gadgets", when TV came in here in 1956, audio went even further out of people's minds, and when everything went solid state it got even worse, until the laws on import duties were changed to allow foreign products in from mainly Japan. I am not an expert in the tube amps, but closely observe vintage Oz radios for sale on the e-bay. I found that the Oz radios from 30's to early 60's are extremely primitive and electrically boooooooooooooooring. 6A8G-6U7G-6B8G-6V6G-5Y3 , then 6AN7A-6N8-6N8-6M5-6X4 and later 6BE6-6BA6-6AV6-6AQ5-6X4 was pretty much the limit of imagination of Oz engineers. Almost none of the Oz radios have a tuning indicator, very few have an RF stage (6-th valve). Wiring is messy, STC and Kriesler are the messiest ones. In comparison, even Russian radios (I am a Russian) of that era were more advanced. Almost all models had a 6E5G magic eye, 30% of radios had 6L6GT SE output (5W), some had push-pull ultralinear 2x6L6 stages. Those would have a separate bass/treble tone control and a dedicated 6SJ7 1-st audio stage, as well as variable IF bandwidth for distant/local reception. Output transformers were on average twice heavier than in Oz. Primary resistance did not normally exceed 250 Ohm with 15...20H, while in Oz radios 350...500 ohm and 8...10H was a norm. (What bass response can be expected from those undernourished trannies?) Ceramic trimcaps were used, not the wirewound rubbish common in OZ radios. Regards, Alex These old Russian radios sound most advanced indeed. Does this mean that the 6L6GC tube I got with an amp recently, labeled made in the USSR, are great tubes? Cheers Eric Now Russians label the tubes according to the American or European designating system. In those old days Russian tubes had their own numbers in Cyrillic. For example, 6L6GT is 6?3?, 6V6GT is 6?6?, 6SQ7 is 6?2, etc. |
#52
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"Arny Krueger" wrote in message ... "Alex" wrote in message The rule were radios composed of the "All-American 5", being first the late-1930s octal-tubed: 12SA7 (a pentagrid converter, or heptode, combining oscillator and mixer functions) 12SK7 (pentode, IF amplifier) 12SQ7 (triode and dual diode, used for detection and first audio amplifier) 50L6 (beam pentode, power output) 35Z5 (half-wave rectifier for B+ supply) and then the eraly-1950s minature tube version: 12BE6 (pentagrid converter) 12BA6 (pentode, IF amplifier) 12AV6 (triode and dual diode, used for detection and first audio amplifier) 50C5 (beam pentode, power output) 35W4 (half-wave rectifier for B+ supply The B+ was half-wave rectified from the power line (thus limiting B+ to about 150 volts) , and one side of the chassis was randomly connected to either the hot or neutral side of the power line since the power plug was not polarized. The output transformer was miniscule, and the 4" speaker was egregious. Needless to say, there was no tuning indicator. When FM became popular, a few more tubes were added, but the basic recipie was essentially unchanged. Eventually, even most B&W and then color TV sets were based on this kind of cheap-and-dirty technology. Series heater connection has never taken root in Russia. Though mains was not polarised, a power transformer was always used. (6.3V tubes were common, 12.6V - very rare). And a fuse. (Such luxury as a fuse was never found in Aussie radios.) |
#53
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
Andre Jute wrote:
On Jul 9, 11:39 am, keithr wrote: Bret L wrote: RR was also first rate, but volume production was not their thing at all. The figures are, I believe: Rolls Royce: 82117 Ford (UK): 30478 Packard: 55523 I would normally say you lost the point 86 to 82, Keith, on the assumption that if the fiercely protective Rolls-Royce produced less than half of total production of their own design, then it should be clear that "volume production was not their thing at all". But in wartime, any port in a storm, the rules change. It seems to me that if under such huge pressure RR still produced half of all engines made to that design, they had the production down pretty much pat. Andre Jute Plain common sense costs nothing except application The point was that that RR produced more Merlins than anybody despite "volume production was not their thing at all.", although it has to be said that they produced them over a longer period than the other manufacturers. |
#54
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"flipper" wrote in message
news The rule were radios composed of the "All-American 5", being first the late-1930s octal-tubed: 12SA7 (a pentagrid converter, or heptode, combining oscillator and mixer functions) 12SK7 (pentode, IF amplifier) 12SQ7 (triode and dual diode, used for detection and first audio amplifier) 50L6 (beam pentode, power output) 35Z5 (half-wave rectifier for B+ supply) and then the eraly-1950s minature tube version: 12BE6 (pentagrid converter) 12BA6 (pentode, IF amplifier) 12AV6 (triode and dual diode, used for detection and first audio amplifier) 50C5 (beam pentode, power output) 35W4 (half-wave rectifier for B+ supply The B+ was half-wave rectified from the power line (thus limiting B+ to about 150 volts) , and one side of the chassis was randomly connected to either the hot or neutral side of the power line since the power plug was not polarized. The output transformer was miniscule, and the 4" speaker was egregious. Needless to say, there was no tuning indicator. When FM became popular, a few more tubes were added, but the basic recipie was essentially unchanged. Eventually, even most B&W and then color TV sets were based on this kind of cheap-and-dirty technology. Which meant that the vast majority of people could afford them. True, there was nothing wrong with the market penetration that this cheap-and-dirty equipment achieved. The "All American 5' wasn't the 'dirtiest', though. The NAZI era 'peoples radio' used a whopping 3 tubes, including rectifier. http://www.antiqueradio.org/VolksempfaengerVE301dyn.htm Regrettably, no schematic. Reading between the lines, I suspect it used some kind of regenerative circuit. And the even cheaper DKE 38 http://www.antiqueradio.org/KleinempfaengerDKE38.htm with a 'reed' speaker. Tell me again about the 'egregious' AA5 speaker. Yes, that reed speaker (I presume the reed replaced the spider) had to be a real hoot (no pun intended). ;-) The AA5 4 inch permanent magnet speaker had no highs, no lows, and it wasn't even Bose! ;-) Prior to the second war, field coil speakers were more common, and at least that added a filter choke to the power supply. Of course, the poorly filtered DC in the speaker field coil caused some hum of its own, so the better sets of the day had a hum-bucker coil. Avoiding speaker treble response improved the audible SNR by attenuating whistles and cross channel-noise. Without the treble roll-off this cheap crap would have been even harder on the ears given the sloppy bandpass of the single IF stage. Avoiding bass response made the hum from the el-cheapo power supply less audible. Some *deluxe* sets had a built-in LF second-harmonic generation circuit to give the perception of low bass due to a well-known property of the human ear. Making the speaker highly efficient (at the expense of Xmax) made it loud given the meager power output of the electronics. It also made it nonlinear, particularly at low frequencies. Of course attenuating low frequencies make the cheap cabinet less likely to resonate and buzz. The American design swapped 'more tubes' for the power transformer. I don't see that. There would have been a rectifier tube, power transformer or not. There were *upgraded* versions of the AA5 that were sold in rural communities. They either had a second IF stage or a TRF amplifier before the mixer, or both. My rural cousins had them. |
#55
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"Patrick Turner" wrote in message ... I don't recall ever seeing one single Russian import though. There was a cheap Russian radio for poor folks: Moskvitch. Four valves: 6SA7-6B8M (reflex IF/AF)-6V6GT-6X5GT. I saw one solds on Oz e-bay for A$202! But it was not popular. Those who could afford bought more decent radios. Those who could not listened to propaganda via a wired "translation": Every flat in every house in a big city would have an audio network (30V) and "translation" speakers were common, comprising a volume control, an audio stepdown transformer, and a speaker. Long waves were used for broadcasting in Russia because of good range. One powerful station would cover a radius of hundreds kilometers. Every village could listen to propaganda and music. In Kamchatka for example, one station used two neighbouring mountains to support the LW antenna. Imagine one station covering both NSW and ACT! Alex |
#56
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
wrote in message
On Jul 9, 5:40 am, "Arny Krueger" wrote: wrote in message On Jul 8, 2:17 pm, Bret L wrote: A Mustang took about the same materials cost and about half the manufacturing labor to build as did a Spitfire. Arguably the Spitfire was prettier. It's worth reading Len Deighton's novel "Fighter," in which he goes into the different manufacturing costs in detail. He laments the phasing out of the Republic P47 in favor of the very much cheaper Mustang, which had a significantly worse record of killing pilots in accidents. A ludicrous comparison given all of the other differences that were involved. The comparison is valid given that the prime role for both designs was the long-range escort for the 8th Air Force daylight bombing missions to Germany. The comparison is invalid given that the war was not static. Mr. Atkinson's ignorance of the dynamics of war and the roles of these airplanes is demonstrated by his claim that they were primarily long-range escort planes. The fact is that both the P47 and the Mustang served in both ground attack/support and escort roles. Wikipedia says: "The P-47 was effective in air combat but proved especially adept at ground attack. " and: (from the Wikipedia article about the P51 Mustang) "Beginning in late February 1944, 8th Air Force fighter units began systematic strafing attacks on German airfields that picked up in frequency and intensity throughout the spring, with the objective of gaining air supremacy over the Normandy battlefield. In general, these were conducted by units returning from escort missions, but beginning in March, many groups also were assigned airfield attacks instead of bomber support. On 15 April, VIII FC began Operation Jackpot, attacks on specific Luftwaffe fighter airfields, and on 21 May, these attacks were expanded to include railways, locomotives, and rolling stock used by the Germans to transport materiel and troops, in missions dubbed "Chattanooga".[37] The fact is that the initial P-51s that were delivered were incompetent as high altitude bomber escorts due to the limitations of their engines. They were thus initially used in ground attack and ground support roles. Just because the engines were upgraded didn't mean that their ground support role went away. The P47 was a very robust, heavy, but aerodynamically inefficient airplane. It was the vastly increased aerodynamic competence of the P51 that made it suitable for far more long-range missions. With long range comes greater risk. Of course John, your analysis if it could be even called an analysis, does not include this important factor. Wars have this nasty tendency to "heat up". Thus there were more casualties per sortie as the war progressed and the fighting became more desperate. This abated for the allies after they achieved air supremacy, of course. However by then, the war was mostly in the past. Note the absence of any kind of fair comparison and no relevant [sic] statistics from an independent source. I referred to Len Deighton's comments, in his novel "Fighter," which , like the companion "Bomber," includes a great deal of factual information. I would have thought that Deighton _was_ an "independent source." As usual John, you are fact-challenged and are only reciting anecdotes from a single, very narrow source. Your arrogant sloppiness in your day job seems to be dominating even your reading for relaxation. |
#57
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"Alex" wrote in message
Series heater connection has never taken root in Russia. Though mains was not polarised, a power transformer was always used. (6.3V tubes were common, 12.6V - very rare). And a fuse. (Such luxury as a fuse was never found in Aussie radios.) Series connection of heaters is more technically challenging in localities where the normal power line voltage is 220+ volts as compared to the 120 volt norm in the US. |
#58
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"keithr" wrote in message
Bret L wrote: On Jul 7, 11:29 pm, keithr wrote: Andre Jute wrote: On Jul 8, 12:13 am, wrote: On Jul 7, 6:39 pm, Andre Jute wrote: Ludwig claims among other inanities that Ferrari engines are copies of Packard engines. Ditto for the Merlin engine; Merlin was a Rolls-Royce design... Yes it was, based on the Schneider Cup-winning engine. But RR did eventually license the Merlin to Packard, who manufactured the engine to power the P51 Mustang. John Atkinson Editor, Stereophile Yes, I know all that, John. But that Rolls-Royce licensed the engine to Packard doesn't make it a "Packard design" as Ludwig tries to claim; it remains forever a Rolls-Royce design. Ludwig, besides making rather large claims of this ludicrous nature, is a copyright thief who in the past has claimed that my copyright material belonged to him by right of repeated theft. He is a perfect stranger to logic. Andre Jute Visit Andre's books at http://www.audio-talk.co.uk/fiultra/THE%20WRITER'S%20HOUSE.html The P51 was originally developed to an RAF requirement. Right, it was a Kelly Johnson hurry-up project, concept to flying prototype in maybe 120 days. Ironically, North American Aviation was unable to interest the American Army Air Force in the P51 until after it was upgraded and proven by the British. It was fitted with a Packard engine which gave so-so performance especially at high altitude. No, it was an Allison. Agreed, the initial P51 engine was an Allison which limited the airframe's performance, particularly with regard to altitude. Sorry, you are correct, somehow I got Packards on the brain, and of course it was Allison who went on to build the copy Merlins No, Allison was a division of General Motors, while Packard who copied the Merlin was a completely independent and even competitive enterprise. Packard competed with the the upper end of the Cadillac division of GM. Packard were in the high end, high personal service, high performance end of the car market. I'm intimately familiar with the difference between the two because I know where their factories were. My father bailed from Packard just before they went broke in the early 50s, to work for General Motors for the rest of his life. AFAIK Allison never produced an engine that could compete head-to-head with the Merlin. Allison has been part of Rolls Royce since 1995. |
#59
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"keithr" wrote in message
The point was that that RR produced more Merlins than anybody despite "volume production was not their thing at all.", I think it depends on what your standards are. By European standards, Rolls could do mass production. By US standards, they were shall we say, limited. although it has to be said that they produced them over a longer period than the other manufacturers. That's a very relavant point. The first production run of Mustang engines took place in 1935. The first run of Packard copies took place in late 1941. That gives Rolls Royes a 6 year head start. AFAIK, Packard's volume production of this engine stopped at the end of the war, late 1945. They quickly returned to building high end automobiles. I suspect that Rolls Royce did not stop producing this engine so abruptly. |
#60
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
In article ,
"Arny Krueger" wrote: "flipper" wrote in message news The rule were radios composed of the "All-American 5", being first the late-1930s octal-tubed: 12SA7 (a pentagrid converter, or heptode, combining oscillator and mixer functions) 12SK7 (pentode, IF amplifier) 12SQ7 (triode and dual diode, used for detection and first audio amplifier) 50L6 (beam pentode, power output) 35Z5 (half-wave rectifier for B+ supply) and then the eraly-1950s minature tube version: 12BE6 (pentagrid converter) 12BA6 (pentode, IF amplifier) 12AV6 (triode and dual diode, used for detection and first audio amplifier) 50C5 (beam pentode, power output) 35W4 (half-wave rectifier for B+ supply The B+ was half-wave rectified from the power line (thus limiting B+ to about 150 volts) , and one side of the chassis was randomly connected to either the hot or neutral side of the power line since the power plug was not polarized. The output transformer was miniscule, and the 4" speaker was egregious. Needless to say, there was no tuning indicator. When FM became popular, a few more tubes were added, but the basic recipie was essentially unchanged. Eventually, even most B&W and then color TV sets were based on this kind of cheap-and-dirty technology. Which meant that the vast majority of people could afford them. True, there was nothing wrong with the market penetration that this cheap-and-dirty equipment achieved. The "All American 5' wasn't the 'dirtiest', though. The NAZI era 'peoples radio' used a whopping 3 tubes, including rectifier. http://www.antiqueradio.org/VolksempfaengerVE301dyn.htm Regrettably, no schematic. Reading between the lines, I suspect it used some kind of regenerative circuit. Look down towards the bottom of the page, there is a schematic there. -- Regards, John Byrns Surf my web pages at, http://fmamradios.com/ |
#61
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
"John Byrns" wrote in message
In article , "Arny Krueger" wrote: "flipper" wrote in message news The rule were radios composed of the "All-American 5", being first the late-1930s octal-tubed: 12SA7 (a pentagrid converter, or heptode, combining oscillator and mixer functions) 12SK7 (pentode, IF amplifier) 12SQ7 (triode and dual diode, used for detection and first audio amplifier) 50L6 (beam pentode, power output) 35Z5 (half-wave rectifier for B+ supply) and then the eraly-1950s minature tube version: 12BE6 (pentagrid converter) 12BA6 (pentode, IF amplifier) 12AV6 (triode and dual diode, used for detection and first audio amplifier) 50C5 (beam pentode, power output) 35W4 (half-wave rectifier for B+ supply The B+ was half-wave rectified from the power line (thus limiting B+ to about 150 volts) , and one side of the chassis was randomly connected to either the hot or neutral side of the power line since the power plug was not polarized. The output transformer was miniscule, and the 4" speaker was egregious. Needless to say, there was no tuning indicator. When FM became popular, a few more tubes were added, but the basic recipie was essentially unchanged. Eventually, even most B&W and then color TV sets were based on this kind of cheap-and-dirty technology. Which meant that the vast majority of people could afford them. True, there was nothing wrong with the market penetration that this cheap-and-dirty equipment achieved. The "All American 5' wasn't the 'dirtiest', though. The NAZI era 'peoples radio' used a whopping 3 tubes, including rectifier. http://www.antiqueradio.org/VolksempfaengerVE301dyn.htm Regrettably, no schematic. Reading between the lines, I suspect it used some kind of regenerative circuit. Look down towards the bottom of the page, there is a schematic there. Natch, a regenerative circuit. I seriously doubt that this one met FCC Part 15... |
#62
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 8, 7:21*pm, wrote:
On Jul 8, 2:17*pm, Bret L wrote: *A Mustang took about the same materials cost and about *half the manufacturing labor to build as did a Spitfire. Arguably the Spitfire was prettier. It's worth reading Len Deighton's novel "Fighter," in which he goes into the different manufacturing costs in detail. He laments the phasing out of the Republic P47 in favor of the very much cheaper Mustang, which had a significantly worse record of killing pilots in accidents. There are ten times as many Mustangs flying today, although almost twice as many Jugs were built. One reason is that the US military used the Mustang as late as 1955, it having been extensively used in Korea, whereas the P-47 was gotten rid of after WWII as was the P-38. The P-47 used the desireable R-2800 which was in airline service, so the parts were valuable, whereas Packard Merlins were new in crate for just over scrap. But I think the big difference was just that in the 50s and early 60s a lot of people wanted Mustangs and so a lot were saved. The Mustang was and is a very desireable warbird and it was very popular with USAFR and ANG pilots who flew it very late in its career as well.(I think there were ANG outfits that managed to keep them as late as 1955, this having been made feasible because the A model Sabres had fatigue problems and were dispatched like cordwood after Korea, as were all the straightwing F-84s) Foreign air forces flew it extensively as well. My father actually worked for North American Aviation postwar and later sold metalworking and corrosion control products. He had some dealings with Latin air forces which operated the Mustang. The Thunderbolt was renowned, as were most all Republic aircraft, for toughness and ability to take battle damage. and pilot protection. The Mustang was well designed too but it was a smaller, lighter aircraft and it had some peculiarities such as, the belly scoop mounted radiators-there are three, for oil, coolant, and intercooler coolant. It could not be ditched without flipping over, for instance. In the late 50s and early 60s the Mustang was "civilianized" by companies like Cavalier with spiffy paint schemes, permanent tip tanks, extended canopies, plush cockpits and the like. Fully outfitted such an airplane could be had for a little more than a new Beech Bonanza, and in fact there were FBOs that rented them out as one would a Cessna. Based on that (the crash rate wasn't freakishly high) I'd say the P-51 wasn't all that tough to fly. The Jug wasn't either, although there were virtually none left by even 1950: that there are even twenty left today is because of inefficiency in the scrap-out process. As for efficiency as a war machine, I'd say the Jug could carry a bigger bombload and was perhaps better for low level strafing and bombing, but for air to air combat the Mustang was unexcelled particularly in the ETO. The P-47 was capable of taking a lot more battle damage and getting you hiome, but the Mustang had to be a better tool for bagging 109s and 190s if that was what you were there for in the first place. |
#63
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 9, 4:35*am, "Arny Krueger" wrote:
"Alex" wrote in message I am not an expert in the tube amps, but closely observe vintage Oz radios for sale on the e-bay. I found that the Oz radios from 30's to early 60's are extremely primitive and electrically boooooooooooooooring. 6A8G-6U7G-6B8G-6V6G-5Y3 , then 6AN7A-6N8-6N8-6M5-6X4 and later 6BE6-6BA6-6AV6-6AQ5-6X4 was pretty much the limit of imagination of Oz engineers. Almost none of the Oz radios have a tuning indicator, very few have an RF stage (6-th valve). Wiring is messy, STC and Kriesler are the messiest ones. In comparison, even Russian radios (I am a Russian) of that era were more advanced. Almost all models had a 6E5G magic eye, 30% of radios had 6L6GT SE output (5W), some had push-pull ultralinear 2x6L6 stages. Those would have a separate bass/treble tone control and a dedicated 6SJ7 1-st audio stage, as well as variable IF bandwidth for distant/local reception. Output transformers were on average twice heavier than in Oz. Primary resistance did not normally exceed 250 Ohm with 15...20H, while in Oz radios 350...500 ohm and 8...10H was a norm. (What bass response can be expected from those undernourished trannies?) Ceramic trimcaps were used, not the wirewound rubbish common in OZ radios. All of the above sounds very high tech compared to the usual USA AM radio receiver of those days. The *rule were radios composed of the "All-American 5", *being first the late-1930s octal-tubed: 12SA7 (a pentagrid converter, or heptode, combining oscillator and mixer functions) 12SK7 (pentode, IF amplifier) 12SQ7 (triode and dual diode, used for detection and first audio amplifier) 50L6 (beam pentode, power output) 35Z5 (half-wave rectifier for B+ supply) and then the eraly-1950s minature tube version: 12BE6 (pentagrid converter) 12BA6 (pentode, IF amplifier) 12AV6 (triode and dual diode, used for detection and first audio amplifier) 50C5 (beam pentode, power output) 35W4 (half-wave rectifier for B+ supply The B+ was half-wave rectified from the power line (thus limiting B+ to about 150 volts) , and one side of the chassis was randomly connected to either the hot or neutral side of the power line since the power plug was not polarized. *The output transformer was miniscule, and the 4" speaker was egregious. Needless to say, there was no tuning indicator. When FM became popular, a few more tubes were added, but the basic recipie was essentially unchanged. Eventually, even most *B&W and then color TV sets were based on this kind of cheap-and-dirty technology. Before WWII the AA5 was called a "midget radio" and better sets were made with proper power transformers except for those specifically sold as AC-DC-domestic DC in apartments was in many cities until the JFK/MM era, sometimes Nixon, and in the trolley car days 25 Hz was not unknown either. After WWII TV and hi-fi (sic) made radio a secondary concern so pure domestic radios went to AC-DC heater strings very extensively. Some of these sets like the Zenith K-725 are desireable today. It has to be said that when excellent RF parts and design were used, the AA5 was capable of very remarkable performance. Even the vaunted GE Superadio would not outperform many good ones. |
#64
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 9, 4:45*am, Patrick Turner wrote:
John Byrns wrote: In article , *Patrick Turner wrote: Bret L wrote: *This month marks, approximately, the 60th anniversary of the Williamson amplifier *in the United States. It was first described in Wireless World magazine in the UK in 1947, but little notice was taken at first by the American hobbyist-or professional. However, requests by amateurs and pros alike for a factory wound variant of the output transformer described in the article eventually provoked the American transformer companies to make a suitable unit, with American style 16/8/4 ohm output taps rather than the British style of multiple series parallel jumpers, and soon the various poopular magazines were covering the US versions, each magazine promoting one or another variant according to, one suspects, which transformer company advertised the most in that magazine. Yeah, the american makers' response to Willy's ideas was "how do we dumb down this too-hard-to-wind tranny and make a profit?" Looked to me like the British amp makers had pretty much the same attitude. *The Williamson was a revolution more in thought than in initial results. American ' fidelity nuts' were building prewar designs without feedback, primarily, and with triodes of low amplification factor. Like the first F1 Lotus race car entered at Indianapolis, it made a mediocre showing-but how it did it precipitated a technical revolution. *The Williamson did away with coupling transformers and was built from low cost parts, save only the output transformer. It needed no bias supply which then meant batteries or a tube rectified affair necessitating a protection relay. Protection relay? With bias supplied by batteries or tube rectifiers as specified above a protection relay is almost a necessity. I've never seen a mass made tube amp with batteries for bias. Batteries go flat or leak all over the place and cost more than other means of biasing, so no batteries were ever approved by the company bean counter. I never seen any mass made tube amp with a with any active protection whatsovever. Several non-WE theater and PA amps made prewar did. They sometimes used Mallory bias cells, other times regular big radio B batteries as made by Burgess. Of course, these were sold to independent movie houses, churches and whatnot and probably never on any small, insignificant island markets, so you wouldn't. Just as I, living in a country where cricket is unheard of, never see cricket bats around....I do see soccer balls because soccer is a popular sport-for 11 year olds. |
#65
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
The B+ was half-wave rectified from the power line (thus limiting B+ to about 150 volts) , and one side of the chassis was randomly connected to either the hot or neutral side of the power line since the power plug was not polarized. *The output transformer was miniscule, and the 4" speaker was egregious. Needless to say, there was no tuning indicator. When FM became popular, a few more tubes were added, but the basic recipie was essentially unchanged. Eventually, even most *B&W and then color TV sets were based on this kind of cheap-and-dirty technology. Which meant that the vast majority of people could afford them. By 1960, anyone who wanted one could afford a TV set of considerable size (for the time). Series heater string AC-DC operation shaved cost and meant there was no PT to fail. We always had Zeniths in my house growing up and from the tube layouts I saw in the books which my mother saved I think most had a power transformer. The "All American 5' wasn't the 'dirtiest', though. The NAZI era 'peoples radio' used a whopping 3 tubes, including rectifier. http://www.antiqueradio.org/VolksempfaengerVE301dyn.htm And the even cheaper DKE 38 http://www.antiqueradio.org/KleinempfaengerDKE38.htm with a 'reed' speaker. Tell me again about the 'egregious' AA5 speaker. The American design swapped 'more tubes' for the power transformer. Of course, there was also the 'All American 6' and other designs. The most reliable antique radio in existence is the National SW-3. It has three tubes, but it has neither a power supply nor an audio power stage. It was often used with a combination power supply and power amplifier which had another three or four tubes. It is a regen set and requires a skilled operator, but is stable enough to copy SSB on the ham bands. By contrast immediately prior to WWII some radio consoles grew to colossal size with up to 35 tubes. TV killed that market and serious radio became the domain of communications receivers and hi-fi tuners. |
#66
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
Gee, I thought Australia DID ****IN MATTER A LOT in the bygone days in a different world after 1939 to about now. The US wasn't about to let Oz go to the japs because it had very big business interests here. In fact the US has done well out of Oz, and it wouldn't like to lose it; it'd be like losing a state of the Union. But your'e about right about how US exporters often thought about Oz, too much trouble to export to and not enough sales. Now its very hard to find anything worth buying in the shops with a made in the USA sticker. Maybe its different now. I don't buy much od any damn thing from anyone, so what would I know? Strategically Australia was important from a military standpoint, but not from a hi-fi equipment one. They never were a significant consumer or producer of hi-fi.That's what i was talking about. If we are talking hi-fi, then we must look elsewhere. As far as transformer quality, the best output transformers were not used in mass marketed products but sold as standalone products. They were bought by hobbyists and also by companies building bespoke equipment for the wealthy and commercial installations. Some commercial amps had great transformers. Fairchild and Marantz and later Harmon Kardon, in the US, and Radford in the UK. The Willy design from the article was not nearly as good as the top Partridge nor the top Peerless 20-20 plus, UTC Linear Standard, or Freed products. The Acrosound and early Dyna transformers were quite good. By the ST70 they had cheapened them very substantially. I have heard that one big concern with the Dyna was shaving weight to keep post down on the kit, as they were just under a certain break in shipping cost. When we talk about Peerless it is important to differentiate the 20-20 Plus and 20-20 designs which were excellent from the OEM designs which were merely good. |
#67
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
On Jul 9, 7:15*am, "Alex" wrote:
"Arny Krueger" wrote in message ... "Alex" wrote in message The *rule were radios composed of the "All-American 5", *being first the late-1930s octal-tubed: 12SA7 (a pentagrid converter, or heptode, combining oscillator and mixer functions) 12SK7 (pentode, IF amplifier) 12SQ7 (triode and dual diode, used for detection and first audio amplifier) 50L6 (beam pentode, power output) 35Z5 (half-wave rectifier for B+ supply) and then the eraly-1950s minature tube version: 12BE6 (pentagrid converter) 12BA6 (pentode, IF amplifier) 12AV6 (triode and dual diode, used for detection and first audio amplifier) 50C5 (beam pentode, power output) 35W4 (half-wave rectifier for B+ supply The B+ was half-wave rectified from the power line (thus limiting B+ to about 150 volts) , and one side of the chassis was randomly connected to either the hot or neutral side of the power line since the power plug was not polarized. *The output transformer was miniscule, and the 4" speaker was egregious. Needless to say, there was no tuning indicator. When FM became popular, a few more tubes were added, but the basic recipie was essentially unchanged. Eventually, even most *B&W and then color TV sets were based on this kind of cheap-and-dirty technology. Series heater connection has never taken root in Russia. Though mains was not polarised, a power transformer was always used. (6.3V tubes were common, 12.6V - very rare). And a fuse. (Such luxury as a fuse was never found in Aussie radios.) An interesting corollary is that Russian cameras always had excellent optics but ill-fitting mechanicals. Radios and later TVs, though never really cheap, were still relatively subsidized because the Sovs wanted their people to have clear access not only to propaganda but also classical music and other art considered uplifting by Soviet doctrine. Getting caught listening to such foreign broadcasts as you could get was a no-no. In the time of Stalin it got you shot. I'm sure Party membership conferred additional benefits. When my father visited GUM there were ornate radios there, but the foreign currency shop had Japanese ones which seemed to be in much demand.maybe the local ones weren't all that. |
#68
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
AFAIK Allison never produced an engine that could compete head-to-head with the Merlin. *Allison has been part of Rolls Royce since 1995. They very certainly did. The late F-82 Twin Mustang reverted to Allison power because RR refused to license further Packard production and politics demanded new US production of engines. The core Allison engine was fully the equal of the Merlin and superior in some respects, but it did not have the altitude capability without turbocharging and the Mustang airframe was not, unlike the P-38, capable of taking the turbos of the day, huge standalone affairs the size and weight of a turbojet engine. So the last dash numbers of Allisons had in essence a Merlin two stage two speed blower section and they had every bit the altitude performance of any Merlin and indeed rivalled the early Griffon. Now you might ask, Why were we building Twin Mustangs instead of using the P-38 which already existed, to do the same job? Well, we had already destroyed almost all the P-38s, and Lockheed wasn't about to build any more. Not with the F-104 on the drawing board. A P-38 with the long known problems that design had properly fixed-by 1942 they knew it was a great design with some fixable but flagrant flaws, like slow and large gear doors that made a single engine takeoff impossible except under ideal conditions-would have been a really impressive aircraft. One could argue the same of the 104, but that's another matter. BTW, Allison Gas turbine was bought by RR, but the entirely separate Allison Transmission is still GM property AFAIK-unlike Detroit Diesel and EMD. |
#69
Posted to rec.audio.opinion,rec.audio.tubes
|
|||
|
|||
60 Years of high Fidelity: The Williamson Amplifier
AFAIK, Packard's volume production of this engine stopped at the end of the war, late 1945. They quickly returned to building high end automobiles. I suspect that Rolls Royce did not stop producing this engine so abruptly. They made Merlins as late as, I think, 1955 for the Canadian DC-4 variant and for the air forces operating Lancaster variants. There were also the V12 Meteor and V8 Meteorite, tank and other vehicle applications having significant commonality with the Merlin. Most of the time when you read of a Merlin engined car or truck, it's really a Meteor. You couldn't really drive anything but a LSR car with the Merlin supercharger active, as any normal throttle position change as in driving a car would blow the supercharger drive line up. Packard's mechanical design skills were fully the equal of RR, although their cars did not have the exalted price and status especially after the war. Where prewar the Twin Six V-12 had been at the apex of car engineering status, postwar they had a competent but dull lineup of straight 8s and V8s. In my opinion they underpriced themselves out of the business-if they had retained the V12 and stayed above Cadillac and Lincoln they might have made it. Packard DID design their own automatic transmission, which RR never did, and the RR V-8 was really largely a copy of an Oldsmobile engine-like Bugattis and Millers, certain parts interchange. |
Reply |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
FA: Heath Williamson W-2M amplifier/preamp/power supply | Vacuum Tubes | |||
FA: Heath Williamson W-2M Amplifier/preamp/power supply | Marketplace | |||
Williamson Amplifier-a good web page | Vacuum Tubes |