Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Speaker frequency response measurements
Is there a standard input level(or output level) at which speaker
frequency response measurements are made? I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? George Deliz |
#2
|
|||
|
|||
Speaker frequency response measurements
George,
how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. So you need to measure either in an anechoic chamber, or you need to use special software like ETF that can apply a "gate" to stop reading before any reflections get into the measuring microphone. --Ethan |
#3
|
|||
|
|||
Speaker frequency response measurements
George,
how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. So you need to measure either in an anechoic chamber, or you need to use special software like ETF that can apply a "gate" to stop reading before any reflections get into the measuring microphone. --Ethan |
#4
|
|||
|
|||
Speaker frequency response measurements
George,
how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. So you need to measure either in an anechoic chamber, or you need to use special software like ETF that can apply a "gate" to stop reading before any reflections get into the measuring microphone. --Ethan |
#5
|
|||
|
|||
Speaker frequency response measurements
George Deliz wrote:
Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. |
#6
|
|||
|
|||
Speaker frequency response measurements
George Deliz wrote:
Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. |
#7
|
|||
|
|||
Speaker frequency response measurements
George Deliz wrote:
Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. |
#8
|
|||
|
|||
Speaker frequency response measurements
"Ethan Winer" ethanw at ethanwiner dot com wrote in message ...
George, how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Oh, please. This issue has been EXCEEDINGLY well documented and and that documentation is readily available to anyone making a modest effort to find it, Mr. Winer. Consider, for example: Gander, M., "Dynamic Linearity and Power Compression in Moving-Coil Loudspeakers," J. Audio Eng. Soc., vol 34, no 9, 1986 Sept. You don't have to wade far into this article, because by the third page, he compares normalized frequency response curves of the same speaker measured at 1 watt and 100 watt, which show significant response differences exceeding, at some frequencies, 5 dB. Consider, as well: Henricksen, C. "Heat Transfer Mechanisms in Loudspeakers: Analysis, Measurement and Design,"J. Audio Eng. Soc., vol 35, no 10, 1987 Oct. Showing similar results. And, in ANY reasonably comprehensive model of speakers accounting for even first order non-linearities, theoretically, there are PLENTY of reasons why the frequency response of a loudspeaker WILL change with power level. Indeed, there is not even a linear correspondance between input power and output SPL. Here are just SOME of the reasons why this is true: 1. Since the DC resistance of the voice coils are temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, the bulk efficiency of the system changes. 2. And since the DC resistance of the voice coil is temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, and since over most of the range of a driver, the electrical impedance is dominated by the DC resistance, the load presented to the crossover changes and thus the crossover transfer function changes and thus the frequency response of the system changes. 3. And, for all those same reasons, the effective damping of the drivers at resonance, dominated by the DC resistance of the voice coil, changes. And since the system response at the low end is quite dependent upon damping, the response at the low end changes as well. 4. The suspension compliance is a non-linear function of excursion, excursion is a complex function of frequency and power, and thus the suspension compleiance is a non-linear function of frequency and power. And since the system response is determined, to some extent, by suspension compliance, there is a dependence on power and SPL due to suspension non-linearities. 5. The Bl factor is also a non-linear function of excursion, and as mentioned, excursion is a complex function of frequency and power, and since efficiency and damping are BOTH dependent upon the Bl factor, the response of the speaker is dependent upon power for that reason as well. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. How is this at all relevant? The poster asked about the SPL dependence of frequency response, which is NOT affected by the room. Is it because to someone whose only tool is a hammer, all problems look like nails? |
#9
|
|||
|
|||
Speaker frequency response measurements
"Ethan Winer" ethanw at ethanwiner dot com wrote in message ...
George, how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Oh, please. This issue has been EXCEEDINGLY well documented and and that documentation is readily available to anyone making a modest effort to find it, Mr. Winer. Consider, for example: Gander, M., "Dynamic Linearity and Power Compression in Moving-Coil Loudspeakers," J. Audio Eng. Soc., vol 34, no 9, 1986 Sept. You don't have to wade far into this article, because by the third page, he compares normalized frequency response curves of the same speaker measured at 1 watt and 100 watt, which show significant response differences exceeding, at some frequencies, 5 dB. Consider, as well: Henricksen, C. "Heat Transfer Mechanisms in Loudspeakers: Analysis, Measurement and Design,"J. Audio Eng. Soc., vol 35, no 10, 1987 Oct. Showing similar results. And, in ANY reasonably comprehensive model of speakers accounting for even first order non-linearities, theoretically, there are PLENTY of reasons why the frequency response of a loudspeaker WILL change with power level. Indeed, there is not even a linear correspondance between input power and output SPL. Here are just SOME of the reasons why this is true: 1. Since the DC resistance of the voice coils are temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, the bulk efficiency of the system changes. 2. And since the DC resistance of the voice coil is temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, and since over most of the range of a driver, the electrical impedance is dominated by the DC resistance, the load presented to the crossover changes and thus the crossover transfer function changes and thus the frequency response of the system changes. 3. And, for all those same reasons, the effective damping of the drivers at resonance, dominated by the DC resistance of the voice coil, changes. And since the system response at the low end is quite dependent upon damping, the response at the low end changes as well. 4. The suspension compliance is a non-linear function of excursion, excursion is a complex function of frequency and power, and thus the suspension compleiance is a non-linear function of frequency and power. And since the system response is determined, to some extent, by suspension compliance, there is a dependence on power and SPL due to suspension non-linearities. 5. The Bl factor is also a non-linear function of excursion, and as mentioned, excursion is a complex function of frequency and power, and since efficiency and damping are BOTH dependent upon the Bl factor, the response of the speaker is dependent upon power for that reason as well. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. How is this at all relevant? The poster asked about the SPL dependence of frequency response, which is NOT affected by the room. Is it because to someone whose only tool is a hammer, all problems look like nails? |
#10
|
|||
|
|||
Speaker frequency response measurements
"Ethan Winer" ethanw at ethanwiner dot com wrote in message ...
George, how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Oh, please. This issue has been EXCEEDINGLY well documented and and that documentation is readily available to anyone making a modest effort to find it, Mr. Winer. Consider, for example: Gander, M., "Dynamic Linearity and Power Compression in Moving-Coil Loudspeakers," J. Audio Eng. Soc., vol 34, no 9, 1986 Sept. You don't have to wade far into this article, because by the third page, he compares normalized frequency response curves of the same speaker measured at 1 watt and 100 watt, which show significant response differences exceeding, at some frequencies, 5 dB. Consider, as well: Henricksen, C. "Heat Transfer Mechanisms in Loudspeakers: Analysis, Measurement and Design,"J. Audio Eng. Soc., vol 35, no 10, 1987 Oct. Showing similar results. And, in ANY reasonably comprehensive model of speakers accounting for even first order non-linearities, theoretically, there are PLENTY of reasons why the frequency response of a loudspeaker WILL change with power level. Indeed, there is not even a linear correspondance between input power and output SPL. Here are just SOME of the reasons why this is true: 1. Since the DC resistance of the voice coils are temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, the bulk efficiency of the system changes. 2. And since the DC resistance of the voice coil is temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, and since over most of the range of a driver, the electrical impedance is dominated by the DC resistance, the load presented to the crossover changes and thus the crossover transfer function changes and thus the frequency response of the system changes. 3. And, for all those same reasons, the effective damping of the drivers at resonance, dominated by the DC resistance of the voice coil, changes. And since the system response at the low end is quite dependent upon damping, the response at the low end changes as well. 4. The suspension compliance is a non-linear function of excursion, excursion is a complex function of frequency and power, and thus the suspension compleiance is a non-linear function of frequency and power. And since the system response is determined, to some extent, by suspension compliance, there is a dependence on power and SPL due to suspension non-linearities. 5. The Bl factor is also a non-linear function of excursion, and as mentioned, excursion is a complex function of frequency and power, and since efficiency and damping are BOTH dependent upon the Bl factor, the response of the speaker is dependent upon power for that reason as well. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. How is this at all relevant? The poster asked about the SPL dependence of frequency response, which is NOT affected by the room. Is it because to someone whose only tool is a hammer, all problems look like nails? |
#11
|
|||
|
|||
Speaker frequency response measurements
Wessel,
Cheaper loudspeakers can become thermally overloaded at higher drive levels and change frequency response as a result. Thanks, that all makes sense. --Ethan |
#12
|
|||
|
|||
Speaker frequency response measurements
Wessel,
Cheaper loudspeakers can become thermally overloaded at higher drive levels and change frequency response as a result. Thanks, that all makes sense. --Ethan |
#13
|
|||
|
|||
Speaker frequency response measurements
Wessel,
Cheaper loudspeakers can become thermally overloaded at higher drive levels and change frequency response as a result. Thanks, that all makes sense. --Ethan |
#14
|
|||
|
|||
Speaker frequency response measurements
Dick,
Here are just SOME of the reasons why this is true: All of that was truly fabulous. Thanks for the detailed explanation. This is what you do best. Is it because to someone whose only tool is a hammer, all problems look like nails? I see you still need to work on common courtesy. :-( Look, people of all levels come to newsgroups asking for help. Some have no clue how audio works and ask pie in the sky questions, and others have questions that are extremely sophisticated. It's often difficult to know someone's level from their questions. So I contribute what I can - be aware of the room when measuring a speaker's response - and folks like you contribute based on their own personal slant and expertise. So lighten up a bit and we'll all help as we can. --Ethan |
#15
|
|||
|
|||
Speaker frequency response measurements
Dick,
Here are just SOME of the reasons why this is true: All of that was truly fabulous. Thanks for the detailed explanation. This is what you do best. Is it because to someone whose only tool is a hammer, all problems look like nails? I see you still need to work on common courtesy. :-( Look, people of all levels come to newsgroups asking for help. Some have no clue how audio works and ask pie in the sky questions, and others have questions that are extremely sophisticated. It's often difficult to know someone's level from their questions. So I contribute what I can - be aware of the room when measuring a speaker's response - and folks like you contribute based on their own personal slant and expertise. So lighten up a bit and we'll all help as we can. --Ethan |
#16
|
|||
|
|||
Speaker frequency response measurements
Dick,
Here are just SOME of the reasons why this is true: All of that was truly fabulous. Thanks for the detailed explanation. This is what you do best. Is it because to someone whose only tool is a hammer, all problems look like nails? I see you still need to work on common courtesy. :-( Look, people of all levels come to newsgroups asking for help. Some have no clue how audio works and ask pie in the sky questions, and others have questions that are extremely sophisticated. It's often difficult to know someone's level from their questions. So I contribute what I can - be aware of the room when measuring a speaker's response - and folks like you contribute based on their own personal slant and expertise. So lighten up a bit and we'll all help as we can. --Ethan |
#17
|
|||
|
|||
Speaker frequency response measurements
Dick Pierce wrote: "Ethan Winer" ethanw at ethanwiner dot com wrote in message ... George, how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Oh, please. This issue has been EXCEEDINGLY well documented and and that documentation is readily available to anyone making a modest effort to find it, Mr. Winer. Consider, for example: Gander, M., "Dynamic Linearity and Power Compression in Moving-Coil Loudspeakers," J. Audio Eng. Soc., vol 34, no 9, 1986 Sept. You don't have to wade far into this article, because by the third page, he compares normalized frequency response curves of the same speaker measured at 1 watt and 100 watt, which show significant response differences exceeding, at some frequencies, 5 dB. Consider, as well: Henricksen, C. "Heat Transfer Mechanisms in Loudspeakers: Analysis, Measurement and Design,"J. Audio Eng. Soc., vol 35, no 10, 1987 Oct. Showing similar results. And, in ANY reasonably comprehensive model of speakers accounting for even first order non-linearities, theoretically, there are PLENTY of reasons why the frequency response of a loudspeaker WILL change with power level. Indeed, there is not even a linear correspondance between input power and output SPL. Here are just SOME of the reasons why this is true: 1. Since the DC resistance of the voice coils are temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, the bulk efficiency of the system changes. 2. And since the DC resistance of the voice coil is temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, and since over most of the range of a driver, the electrical impedance is dominated by the DC resistance, the load presented to the crossover changes and thus the crossover transfer function changes and thus the frequency response of the system changes. 3. And, for all those same reasons, the effective damping of the drivers at resonance, dominated by the DC resistance of the voice coil, changes. And since the system response at the low end is quite dependent upon damping, the response at the low end changes as well. 4. The suspension compliance is a non-linear function of excursion, excursion is a complex function of frequency and power, and thus the suspension compleiance is a non-linear function of frequency and power. And since the system response is determined, to some extent, by suspension compliance, there is a dependence on power and SPL due to suspension non-linearities. 5. The Bl factor is also a non-linear function of excursion, and as mentioned, excursion is a complex function of frequency and power, and since efficiency and damping are BOTH dependent upon the Bl factor, the response of the speaker is dependent upon power for that reason as well. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. How is this at all relevant? The poster asked about the SPL dependence of frequency response, which is NOT affected by the room. Is it because to someone whose only tool is a hammer, all problems look like nails? Thanks for the references and discussion. I had searched google for about an hour and found nothing very helpful. George Deliz |
#18
|
|||
|
|||
Speaker frequency response measurements
Dick Pierce wrote: "Ethan Winer" ethanw at ethanwiner dot com wrote in message ... George, how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Oh, please. This issue has been EXCEEDINGLY well documented and and that documentation is readily available to anyone making a modest effort to find it, Mr. Winer. Consider, for example: Gander, M., "Dynamic Linearity and Power Compression in Moving-Coil Loudspeakers," J. Audio Eng. Soc., vol 34, no 9, 1986 Sept. You don't have to wade far into this article, because by the third page, he compares normalized frequency response curves of the same speaker measured at 1 watt and 100 watt, which show significant response differences exceeding, at some frequencies, 5 dB. Consider, as well: Henricksen, C. "Heat Transfer Mechanisms in Loudspeakers: Analysis, Measurement and Design,"J. Audio Eng. Soc., vol 35, no 10, 1987 Oct. Showing similar results. And, in ANY reasonably comprehensive model of speakers accounting for even first order non-linearities, theoretically, there are PLENTY of reasons why the frequency response of a loudspeaker WILL change with power level. Indeed, there is not even a linear correspondance between input power and output SPL. Here are just SOME of the reasons why this is true: 1. Since the DC resistance of the voice coils are temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, the bulk efficiency of the system changes. 2. And since the DC resistance of the voice coil is temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, and since over most of the range of a driver, the electrical impedance is dominated by the DC resistance, the load presented to the crossover changes and thus the crossover transfer function changes and thus the frequency response of the system changes. 3. And, for all those same reasons, the effective damping of the drivers at resonance, dominated by the DC resistance of the voice coil, changes. And since the system response at the low end is quite dependent upon damping, the response at the low end changes as well. 4. The suspension compliance is a non-linear function of excursion, excursion is a complex function of frequency and power, and thus the suspension compleiance is a non-linear function of frequency and power. And since the system response is determined, to some extent, by suspension compliance, there is a dependence on power and SPL due to suspension non-linearities. 5. The Bl factor is also a non-linear function of excursion, and as mentioned, excursion is a complex function of frequency and power, and since efficiency and damping are BOTH dependent upon the Bl factor, the response of the speaker is dependent upon power for that reason as well. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. How is this at all relevant? The poster asked about the SPL dependence of frequency response, which is NOT affected by the room. Is it because to someone whose only tool is a hammer, all problems look like nails? Thanks for the references and discussion. I had searched google for about an hour and found nothing very helpful. George Deliz |
#19
|
|||
|
|||
Speaker frequency response measurements
Dick Pierce wrote: "Ethan Winer" ethanw at ethanwiner dot com wrote in message ... George, how the frequency reponse changes with changing SPL Theoretically, the frequency response of a loudspeaker will not change at all with SPL. Whether it actually does in practice is a different matter, but it's hard for me to see why it would change much if at all. Oh, please. This issue has been EXCEEDINGLY well documented and and that documentation is readily available to anyone making a modest effort to find it, Mr. Winer. Consider, for example: Gander, M., "Dynamic Linearity and Power Compression in Moving-Coil Loudspeakers," J. Audio Eng. Soc., vol 34, no 9, 1986 Sept. You don't have to wade far into this article, because by the third page, he compares normalized frequency response curves of the same speaker measured at 1 watt and 100 watt, which show significant response differences exceeding, at some frequencies, 5 dB. Consider, as well: Henricksen, C. "Heat Transfer Mechanisms in Loudspeakers: Analysis, Measurement and Design,"J. Audio Eng. Soc., vol 35, no 10, 1987 Oct. Showing similar results. And, in ANY reasonably comprehensive model of speakers accounting for even first order non-linearities, theoretically, there are PLENTY of reasons why the frequency response of a loudspeaker WILL change with power level. Indeed, there is not even a linear correspondance between input power and output SPL. Here are just SOME of the reasons why this is true: 1. Since the DC resistance of the voice coils are temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, the bulk efficiency of the system changes. 2. And since the DC resistance of the voice coil is temperature- dependent, and the voice coil temperature is input-power dependent, and since the bulk of the power dissipation in speakers is in the DC resistance of the voice coil, and since over most of the range of a driver, the electrical impedance is dominated by the DC resistance, the load presented to the crossover changes and thus the crossover transfer function changes and thus the frequency response of the system changes. 3. And, for all those same reasons, the effective damping of the drivers at resonance, dominated by the DC resistance of the voice coil, changes. And since the system response at the low end is quite dependent upon damping, the response at the low end changes as well. 4. The suspension compliance is a non-linear function of excursion, excursion is a complex function of frequency and power, and thus the suspension compleiance is a non-linear function of frequency and power. And since the system response is determined, to some extent, by suspension compliance, there is a dependence on power and SPL due to suspension non-linearities. 5. The Bl factor is also a non-linear function of excursion, and as mentioned, excursion is a complex function of frequency and power, and since efficiency and damping are BOTH dependent upon the Bl factor, the response of the speaker is dependent upon power for that reason as well. Far more difficult is to measure a speaker's frequency response in the first place. As soon as you put any loudspeaker in any room, the room will totally dominate the response. How is this at all relevant? The poster asked about the SPL dependence of frequency response, which is NOT affected by the room. Is it because to someone whose only tool is a hammer, all problems look like nails? Thanks for the references and discussion. I had searched google for about an hour and found nothing very helpful. George Deliz |
#20
|
|||
|
|||
Speaker frequency response measurements
Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz |
#21
|
|||
|
|||
Speaker frequency response measurements
Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz |
#22
|
|||
|
|||
Speaker frequency response measurements
Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz |
#23
|
|||
|
|||
Speaker frequency response measurements
Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz |
#24
|
|||
|
|||
Speaker frequency response measurements
Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz |
#25
|
|||
|
|||
Speaker frequency response measurements
Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz |
#26
|
|||
|
|||
Speaker frequency response measurements
George Deliz wrote: Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz Apparently my newsreader was lying when it said it could not find the mail server. George Deliz |
#27
|
|||
|
|||
Speaker frequency response measurements
George Deliz wrote: Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz Apparently my newsreader was lying when it said it could not find the mail server. George Deliz |
#28
|
|||
|
|||
Speaker frequency response measurements
George Deliz wrote: Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the performance of a piece of equipment is as a function of level. Arny Krueger wrote: George Deliz wrote: Is there a standard input level(or output level) at which speaker frequency response measurements are made? AFAIK there are no generally agreed-upon comprehensive standards for loudspeaker measurements. However there are some customary ways of doing things. For example, 2.82 volts is one common customary input that is used for speaker testing. I believe it corresponds to 1 watt into an 8 ohm resistive load. Output levels are a bit more hard to nail down, because they are affected by the frequency response of the speaker in the chosen test environment. For this reason, it can be non-trivial to characterize the efficiency of a speaker. I know that efficiency measurements are made with a standard 2.8 V input but I have been unable to find a source which specifies a similar standard for frequency response measurements. One finds measurements made at 80, 90, and 100 dB at some chosen frequency or range of frequencies. Also,are there any common specs that allow one to get an idea of how the frequency reponse changes with changing SPL for a given speaker, or alternatively over how wide a range of SPL's the frequency response can be expected to be stable? Nonlinear distortion (THD, IM) gives some indication of how stable the Thanks to all respondents. I had searched google for nearly an hour without finding anything nearly as helpful. George Deliz Apparently my newsreader was lying when it said it could not find the mail server. George Deliz |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Newbie Subwoofer questions | General | |||
Newbie Subwoofer questions | Tech | |||
Mic for measuring frequency response | Tech | |||
Blindtest question | High End Audio |