Home |
Search |
Today's Posts |
#1
Posted to rec.audio.tubes,uk.rec.audio
|
|||
|
|||
Canceling distortion
I am designing a mic pre based on three 6AU6 tubes. The first two are
operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. OK, admittedly these are just simulations at present and yes, Patrick, I have pretty much all the components on hand and I WILL be building it as soon as possible. It is so intriguing I cannot resist. Cheers Ian |
#2
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote: I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. OK, admittedly these are just simulations at present and yes, Patrick, I have pretty much all the components on hand and I WILL be building it as soon as possible. It is so intriguing I cannot resist. If you simply want low distortion I suggest you use semiconductor circuitry. The main reason valve / tube circuitry is used by those who like it is for the *added distortion* that gives the sound more 'colour'. Graham |
#3
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote:
I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. OK, admittedly these are just simulations at present and yes, Patrick, I have pretty much all the components on hand and I WILL be building it as soon as possible. It is so intriguing I cannot resist. Cheers Ian Yes, that sort of thing happens in may amps, expecially SET's with two single ended stages. However it may not work that well in reality, especially if you have reactive loads. -- Nick |
#4
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote
I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. OK, admittedly these are just simulations at present and yes, Patrick, I have pretty much all the components on hand and I WILL be building it as soon as possible. It is so intriguing I cannot resist. Here's some blether: http://www.enjoythemusic.com/magazin...audiopax88.htm look for "Timbre Lock", a couple of para's ahead of heading "Promise Delivered?". What you have, with judicious choice of valves, is the opportunity to tailor the proportions of even and odd harmonics. You can reduce the even but not the odd, by the same principle as in a PP stage...except in the series case you may have dissimilar valves with different input levels and different loads...lots to play with. If you are using SPICE, especially with many of the rough-and-ready models kicking around, then beware that the real spread of distortion will not be very precise, and will miss out some foibles of valve operation. If you *are* using SPICE, then all should surely be clear? You should be able to see how two similarly asymmetrical but opposite signals sum to a more symmetrical one. Symmetrical signals have no even harmonics. Anyway, you may enjoy minimising THD, but an alternative goal would be to optimise the proportions of harmonics to some "golden ratio". Or by ear, which may be another way of doing the first, or the second, depending on your ears, or perhaps not. BTW, using similar valves may not be the best way to go, because they won't be in similar situations. And it's cheating. All the fun is in finding compatible partners. cheers, Ian |
#5
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
er...series cancellation isn't so simple because multiplication is
involved. All the same, you should be able to see what's happening if you make the right pictures. Ian |
#6
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote: I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. OK, admittedly these are just simulations at present and yes, Patrick, I have pretty much all the components on hand and I WILL be building it as soon as possible. It is so intriguing I cannot resist. Cheers Ian Actually, no, what you're seeing is most unlikely to be harmonic cancellation, especially if the observed phenomenon is not frequency dependent. What you're seeing is instead a flattening of the transfer curve brought about by higher current, higher plate load, higher bias, higher plate voltage, or any or all in various combinations dictated by your choice of components. The flattening of the transfer function, and raising it by higher current, lifts the tube out of the noisy regions into linearity; higher current also has a beneficial effect on Miller (there's an article on my netsite which shows how you can use standard slew rate math to discover the minimum amount of current you should put on the driver to avoid Miller screwing your design), all of which adds to the linearity. It is furthermore a very euphonious shift you have brought about, as you will hear when you build the device, in that the disturbing third and higher harmonics should be almost eliminated. Roundabout 1998 an idiot called Chernofsky and his puppetmaster, Creepy LaFevre of Magnequest notoriety, challenged me to a design contest; they ran away after only the power stages were published because their noise generator was simply steamrollered by my ultra-quiet design. John Byrns calculated the distortion proportions of both amps; search Google for the "Bubbaland 300" and you'll find, amid the flamewar, a discussion of my HCHV high-everything concept of silence in tube amps. Everyone who has the sense to design his amps in a simulator (I wrote mine in Excel), rather than build them badly on the bench and spend months trying to gimmick them right by trial and error, and who thinks about what he sees, eventually arrives at HCHV. About a decade ago I made myself very unpopular with the ultrafidelista when I laughed out loud at an article by Reid Welch about harmonic cancellation, and when abused for my lack of solidarity with another Joenetter explained bluntly that the answer lies in that study of the transfer curves which too many of the ultrafidelista are too artistic to commit. (I also pointed out bluntly that I am a real artist--one who earns a substantial living by creating works of art-- and that I know from experience that art--including amps that sound like mine--is created by perspiration, not inspiration.) I'm sorry to disappoint you as well, because frequency free-harmonic cancellation would be a three-star free lunch for tubies everywhere, but I don't think we'll see it in my lifetime. As for claims, heard even on RAT, that so and so injected noise which cancelled greater noise elsewhere, I just giggle; there are ways of distributing noise more benificially, and ways of reducing noise, and above all ways of shaping it euphoniously by reducing higher and odd harmonics more than you can reduce the less disturbing second harmonic, and of simply dividing the noise on the principle of divide and conquer (on a split rail, for instance, the whole amp will be quieter if you partially bypass the bottom leg so that it is split below the cathode the same distance as the bias voltage in the top leg (1)), but none of these are "cancellations" as your headline has it, they are, alas, merely reductions. Andre Jute Visit Jute on Amps at http://members.lycos.co.uk/fiultra/ "wonderfully well written and reasoned information for the tube audio constructor" John Broskie TubeCAD & GlassWare "an unbelievably comprehensive web site containing vital gems of wisdom" Stuart Perry Hi-Fi News & Record Review (1) Now watch the flame war that erupts when someone claims that the point of splitting the bottom leg of a split rail supply is to "inject" the power supply noise at the most beneficial point where it "cancels" the "load noise" (aka "current noise" as in another concurrent thread) in the plate circuit... It ain't injection that matters, of course, but balance of the top and bottom halves, and all the more so when the justification of your expensive split rail supply is a fully balanced amp that is very quiet already. I make this point because what might seem like a subtle distinction of semantics is actually the fast track to a most productive way of thinking about tube amps, and one that every tubie must get right if he is ever to be anything more than a repair hack. |
#7
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Andre Jute wrote: Ian Bell wrote: I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. OK, admittedly these are just simulations at present and yes, Patrick, I have pretty much all the components on hand and I WILL be building it as soon as possible. It is so intriguing I cannot resist. Cheers Ian Actually, no, what you're seeing is most unlikely to be harmonic cancellation, especially if the observed phenomenon is not frequency dependent. What you're seeing is instead a flattening of the transfer curve brought about by higher current, higher plate load, higher bias, higher plate voltage, or any or all in various combinations dictated by your choice of components. The flattening of the transfer function, and raising it by higher current, lifts the tube out of the noisy regions into linearity; higher current also has a beneficial effect on Miller (there's an article on my netsite which shows how you can use standard slew rate math to discover the minimum amount of current you should put on the driver to avoid Miller screwing your design), all of which adds to the linearity. It is furthermore a very euphonious shift you have brought about, as you will hear when you build the device, in that the disturbing third and higher harmonics should be almost eliminated. Roundabout 1998 an idiot called Chernofsky and his puppetmaster, Creepy LaFevre of Magnequest notoriety, challenged me to a design contest; they ran away after only the power stages were published because their noise generator was simply steamrollered by my ultra-quiet design. John Byrns calculated the distortion proportions of both amps; search Google for the "Bubbaland 300" and you'll find, amid the flamewar, a discussion of my HCHV high-everything concept of silence in tube amps. Everyone who has the sense to design his amps in a simulator (I wrote mine in Excel), rather than build them badly on the bench and spend months trying to gimmick them right by trial and error, and who thinks about what he sees, eventually arrives at HCHV. About a decade ago I made myself very unpopular with the ultrafidelista when I laughed out loud at an article by Reid Welch about harmonic cancellation, and when abused for my lack of solidarity with another Joenetter explained bluntly that the answer lies in that study of the transfer curves which too many of the ultrafidelista are too artistic to commit. (I also pointed out bluntly that I am a real artist--one who earns a substantial living by creating works of art-- and that I know from experience that art--including amps that sound like mine--is created by perspiration, not inspiration.) I'm sorry to disappoint you as well, because frequency free-harmonic cancellation would be a three-star free lunch for tubies everywhere, but I don't think we'll see it in my lifetime. As for claims, heard even on RAT, that so and so injected noise which cancelled greater noise elsewhere, I just giggle; there are ways of distributing noise more benificially, and ways of reducing noise, and above all ways of shaping it euphoniously by reducing higher and odd harmonics more than you can reduce the less disturbing second harmonic, and of simply dividing the noise on the principle of divide and conquer (on a split rail, for instance, the whole amp will be quieter if you partially bypass the bottom leg so that it is split below the cathode the same distance as the bias voltage in the top leg (1)), I mean of course "the plate voltage in the top leg", that is, that is, what is left of the B+ after the load resistor drop. but none of these are "cancellations" as your headline has it, they are, alas, merely reductions. Andre Jute Visit Jute on Amps at http://members.lycos.co.uk/fiultra/ "wonderfully well written and reasoned information for the tube audio constructor" John Broskie TubeCAD & GlassWare "an unbelievably comprehensive web site containing vital gems of wisdom" Stuart Perry Hi-Fi News & Record Review (1) Now watch the flame war that erupts when someone claims that the point of splitting the bottom leg of a split rail supply is to "inject" the power supply noise at the most beneficial point where it "cancels" the "load noise" (aka "current noise" as in another concurrent thread) in the plate circuit... It ain't injection that matters, of course, but balance of the top and bottom halves, and all the more so when the justification of your expensive split rail supply is a fully balanced amp that is very quiet already. I make this point because what might seem like a subtle distinction of semantics is actually the fast track to a most productive way of thinking about tube amps, and one that every tubie must get right if he is ever to be anything more than a repair hack. |
#8
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Ian Bell" I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. ** Is there to be an input step-up transformer ?? Be nothing but a damn white noise generator otherwise. ....... Phil |
#9
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote: I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. OK, admittedly these are just simulations at present and yes, Patrick, I have pretty much all the components on hand and I WILL be building it as soon as possible. It is so intriguing I cannot resist. Try a real circuit and perhaps you'll find you won't get the cancellations you say you would, could, might, or did get with simulations. Say you have a first stage gain of 25, then 5mV of mic signal becomes 125mV, and THD should be 0.02%, 2H. It'll be the same % at the output of the gain pot at any setting. Suppose you have the gain up max, then 125mV x 25 gives 3.125V at the second stage anode, and THD produced would be around 0.15%. There will be very little 2H cancellations betwen stage 1 and stage 2. The cathode follower directly coupled with 3V output will add some THD, but it'll only be 0.01% or less, and there isn't enough to cancel that made in the gain stage feeding it, ever. You should be able to work out what THD you will get on the back of an envelope. The spare sides of envelopes comprise some of the hardware of my kitchen table simulator. Computer Power for the Simulator is a 1947 Model HO, ( Human Organic ), which was last tested in 1962 and gave a 135 reading for IQ, although the guys testing it said it was slow, and uncooperative to command programs. But the only time significant 2H cancellation occurs would be when you turn down the gain pot, and only one position where cancellations will be almost complete. Using constant current sources for all your triode loads would reduce the THD at 3V output by around 10dB at least, and you'd never have to worry about THD at all. 0.02% at a volt output is usually utterly inaudible. Not all THD cancels; all the odd numer H sails right on through. The intermodulation products increase with more stages but its unavoidable, and as I said if THD 0.02% and you have not had to rely on loop NFB, you should get glorious sound. Patrick Turner. Cheers Ian |
#10
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Phil Allison wrote:
"Ian Bell" I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. ** Is there to be an input step-up transformer ?? There is 10:1 Be nothing but a damn white noise generator otherwise. Indeed. Ian |
#11
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Patrick Turner wrote:
Try a real circuit and perhaps you'll find you won't get the cancellations you say you would, could, might, or did get with simulations. Agreed. Tube variations for one are not modeled in the simulation. Say you have a first stage gain of 25, then 5mV of mic signal becomes 125mV, and THD should be 0.02%, 2H. It'll be the same % at the output of the gain pot at any setting. Suppose you have the gain up max, then 125mV x 25 gives 3.125V at the second stage anode, and THD produced would be around 0.15%. There will be very little 2H cancellations betwen stage 1 and stage 2. That is pretty much what I get. The cathode follower directly coupled with 3V output will add some THD, but it'll only be 0.01% or less, and there isn't enough to cancel that made in the gain stage feeding it, ever. This is where the cancellation appears to take place in the CF. You should be able to work out what THD you will get on the back of an envelope. The spare sides of envelopes comprise some of the hardware of my kitchen table simulator. I use scrap paper from my printer. Computer Power for the Simulator is a 1947 Model HO, ( Human Organic ), which was last tested in 1962 and gave a 135 reading for IQ, although the guys testing it said it was slow, and uncooperative to command programs. I find that easy to believe ;-) But the only time significant 2H cancellation occurs would be when you turn down the gain pot, and only one position where cancellations will be almost complete. Strangely best cancellation appears to be with the gain pot turned full up. Using constant current sources for all your triode loads would reduce the THD at 3V output by around 10dB at least, and you'd never have to worry about THD at all. 0.02% at a volt output is usually utterly inaudible. I was not particularly trying to avoid it - I was quite looking forward to a bit of tube sound. I did want to limit it as far as possible to 2H distortion which is why I avoided local and global NFB. I was expecting about 0.2% and that is what I get at the 2nd tube anode. I was surprised to find that by tweaking CF values I could reduce this value at the CF output - hence the question about distortion cancellation. What prompted me to tweak the CF values was that my initial CF design produced more distortion than the prior two stage combined. Ian |
#12
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell writes:
I am designing a mic pre based on three 6AU6 tubes. The first two are operated as triodes with no NFB with an overall gain setting pot divider between them and the last is a cathode follower. I have discovered that by judicious selection of the component values in the CF that the predominantly 2H distortion of the first two stages can be reduced by a factor of 10. This effect is not frequency or output level sensitive but does depend on the setting of the inter stage pot - it works best at highest overall gain. I was very surprised to see this effect and wondered if anyone else had come across it. I seem to remember an article somewhere about a two stage amp where the second stage adds the same sort of distortion to the inverse of the waveform and hence reduces overall distortion but I cannot at present lay my hands on it. Pre-distortion linearisation is nothing strange. It is used routinely in industry. Pre-distortion come is two flavors: analogue and digital. The former is about designing stage 1 to have AM/AM and AM/PM characteristics that take out some of the non-linearity of stage 2. Simplistically put: let stage 1 have a gain expansion countering stage 2's gain compression... Digital pre-distortion is about altering the signal in the digital signal procession of the equipment to compensate for the non-linearity of the analog part. Both techniques are used in the transmitters of radio base stations of cellular phone systems. -- Martin Schöön "Problems worthy of attack show their worth by hitting back." Piet Hein |
#13
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Ian Bell" ** Is there to be an input step-up transformer ?? There is 10:1 ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. ..... Phil |
#14
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote: Patrick Turner wrote: Try a real circuit and perhaps you'll find you won't get the cancellations you say you would, could, might, or did get with simulations. Agreed. Tube variations for one are not modeled in the simulation. Say you have a first stage gain of 25, then 5mV of mic signal becomes 125mV, and THD should be 0.02%, 2H. It'll be the same % at the output of the gain pot at any setting. Suppose you have the gain up max, then 125mV x 25 gives 3.125V at the second stage anode, and THD produced would be around 0.15%. There will be very little 2H cancellations betwen stage 1 and stage 2. That is pretty much what I get. The cathode follower directly coupled with 3V output will add some THD, but it'll only be 0.01% or less, and there isn't enough to cancel that made in the gain stage feeding it, ever. This is where the cancellation appears to take place in the CF. I don't think any such cancelation could occur. If you have a direct coupled CF with the 3rd 6AU6, then the load between cathode and 0V for 4mA for Ia will be 30k. In fact with something else connected to the CF, the load could end up being 25k, and for 3V output, perhaps Vgk = 3V/gain of 20 = 0.15V. So the local series voltage NFB with the CF amounts to a gain reduction of 20 times. So if the distortion of the triode without the NFB for 3V into 25k = 2%, then the NFB will reduuce this by a factor of 1/(A+1), so THD with NFB = 2 / (20 + 1) = 0.095%, or about 0.1%. THD beloe 3V is approximately proportional to output voltage so at say 0.2 Vrms for a power needing 2V for clipping, CF THD = 0.1 x 0.2/3 = 0.0066%, somewhat decent peformance. You should be able to work out what THD you will get on the back of an envelope. The spare sides of envelopes comprise some of the hardware of my kitchen table simulator. I use scrap paper from my printer. Computer Power for the Simulator is a 1947 Model HO, ( Human Organic ), which was last tested in 1962 and gave a 135 reading for IQ, although the guys testing it said it was slow, and uncooperative to command programs. I find that easy to believe ;-) But the only time significant 2H cancellation occurs would be when you turn down the gain pot, and only one position where cancellations will be almost complete. Strangely best cancellation appears to be with the gain pot turned full up. Wait until you do a real amp..... Using constant current sources for all your triode loads would reduce the THD at 3V output by around 10dB at least, and you'd never have to worry about THD at all. 0.02% at a volt output is usually utterly inaudible. I was not particularly trying to avoid it - I was quite looking forward to a bit of tube sound. I did want to limit it as far as possible to 2H distortion which is why I avoided local and global NFB. I was expecting about 0.2% and that is what I get at the 2nd tube anode. I was surprised to find that by tweaking CF values I could reduce this value at the CF output - hence the question about distortion cancellation. What prompted me to tweak the CF values was that my initial CF design produced more distortion than the prior two stage combined. You'd have to use a very low value load to force the CF to produce enough THD to cancel that of the preceeding gain stage. I will bet you a dozen schooners that just arrangeing the circuit to get maximal cancellations won't give you the open effortless warm detailed dynamic clear crisp hifi that well set up tubes will give. The main cauise of any THD is the gain tube after the pot. Now if B+ was +300V, and you had a 47k load, and Ea = +130V, then Ia would be 3.61 mA. Neglect the few volts across the cathode R with say 470uF bypass. Ra = approx 10k, µ =36, so gain = 36 x 47 / ( 47 + 10 ) = 30 approximately. Now if you were to use a CCS, the gain = µ = 36 and the THD would be about at least 1/3 of the value for the 47k, and should you wish, B+ could be +250V, Ea at 120V, and Ia = 5ma, and THD would fall even further, because with the high RL and higher Ia, the linearity would peak at more than 3.6mA. If you have the anode curves for a 6AU6 in triode, the CCS load appear as a horizontal line through whatever value of idle current you choose, and the amount of variation between each Ra curve line for each value of grid bias diminishes to a minimum when the load line is a horizontal one. I can assure you the very best "tube sound" comes from triodes operating in pure *voltage* mode with NO anode current change that is easily measured, which is the case with a CCS using a single pnp transistor where the actual load is around 30Mohms, and regarded as a source of current which does not vary regardless of the variation in anode voltage. There will still be some THD even with a CCS. You can calculate what this might be from measuring the spacings between the Ra lines. But usually, the Ra data lines cannot be taken as gospel and are an approximation of the actual curves one might get with a given tube sample. When they may have drawn up the curves 60 years ago, the gear they used may have had 5% errors, and usually the actual THD of a triode with CCS is better than what the curves might suggest. To establish just what goes on you should have a distortion meter with input impedance of at least 500k and capable of measuring 0.005% THD in any voltage between 0.5Vrms and 100Vrms. 0.005% of 0.5Vrms = 25uV, and so to see this on a CRO you need to have a clean test signal with THD = 0.001% max, and be able to remove the 1kHz signal from the signal being examined to below the THD level, and then have a bandpass filter from 1.5kHz to say 10kHz and have an amp to raise the THD by say 20 times to 500uV, or 0.5mV to be able to just see it on your CRO. I built my own oscillator, filters and amp to be able to measure THD this well. But if you asked me to analyse further just what spectral content was in the 0.005%, I would be unable to do it. Its safe to suggest that if the CRO shows the THD as a mainly simple sine wave of 2kHz, then the 3H might be say 10dB down, or be 0.0016%, rather low, and not a major worry, IMHO. Noise and hum will fight against you all the way to trying to get a decent measurement. One could have a tunable band pass filter with a Q = 50, and then the harmonics can be picked out one by one because the noise across such a tiny BW becomes less than the harmonic. I built such a filter, which has a dual gang pot for tuning and 3 opamps and a complex arrangement of NFB and PFB and is incomprehensible to understand. But it works, and cost me only a week to make it work. Using the right sort of sound card and PC and program also can give you what I get with primitive analog test gear I made BC, ( before I had a computer ). I now don't worry too much about the composition of the THD. Tube THD and the resulting IMD isn't ever a problem with a preamp if you are careful with triodes. Pentodes are also quite nice used as such, but need shunt NFB to reduce their high gain. And they have much more noise if used as input tubes for mics. The 6AU6 should be a fine triode for an input situation and compete with 1/2 a 6DJ8 for noise and gain. But you do need a reasonably high input signal for a microphone signal. With a phono amp, the HF are attenuated at about an approximate slope of 6dB/octave above 50Hz, and the phono signal has had its HF boosted, so noise can be very low, but for a mic the signal is flat, and unboosted, and to get low noise the input signal must be high. Using microphones for recording isn't something I have ever done much and if I did i'd probably not use a tube at all but use a j-fet. These are far quieter than any triode. Most triodes have a hissy noise signal of maybe 2uV if you are lucky. DC on the heaters is imperative. Shielding may be needed. Microphony is avoided by careful tube choice. The 2SK369/2SK147 has about 0.14uV in an average sample. The step up tranny can still be used. Once the signal is at over 100mV, tubes are fine. Patrick Turner. Ian |
#15
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Phil Allison wrote: "Ian Bell" ** Is there to be an input step-up transformer ?? There is 10:1 ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. .... Phil If the mic signal = 0.5mV, then gain of 10,000 gives 5Vrms. If the pot gain control is to be used at the -20dB central position, then Vo = 0.5Vrms. Madness? Patrick Turner. |
#16
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Patrick Turner wrote:
Ian Bell wrote: Patrick Turner wrote: Try a real circuit and perhaps you'll find you won't get the cancellations you say you would, could, might, or did get with simulations. Agreed. Tube variations for one are not modeled in the simulation. Say you have a first stage gain of 25, then 5mV of mic signal becomes 125mV, and THD should be 0.02%, 2H. It'll be the same % at the output of the gain pot at any setting. Suppose you have the gain up max, then 125mV x 25 gives 3.125V at the second stage anode, and THD produced would be around 0.15%. There will be very little 2H cancellations betwen stage 1 and stage 2. That is pretty much what I get. The cathode follower directly coupled with 3V output will add some THD, but it'll only be 0.01% or less, and there isn't enough to cancel that made in the gain stage feeding it, ever. This is where the cancellation appears to take place in the CF. I don't think any such cancelation could occur. If you have a direct coupled CF with the 3rd 6AU6, then the load between cathode and 0V for 4mA for Ia will be 30k. In fact with something else connected to the CF, the load could end up being 25k, and for 3V output, perhaps Vgk = 3V/gain of 20 = 0.15V. In the present design the CF is AC coupled to the preceding triode stage. The CF cathode connects to ground via a 1K and 3.3K in series. The junction of these two goes to g1 via 330K. The 1K is bypassed with 47uF. The cathode sits at about 21V and the anode current is about 5mA and g1 is about -5V wrt the cathode. So the local series voltage NFB with the CF amounts to a gain reduction of 20 times. So if the distortion of the triode without the NFB for 3V into 25k = 2%, then the NFB will reduuce this by a factor of 1/(A+1), so THD with NFB = 2 / (20 + 1) = 0.095%, or about 0.1%. THD beloe 3V is approximately proportional to output voltage so at say 0.2 Vrms for a power needing 2V for clipping, CF THD = 0.1 x 0.2/3 = 0.0066%, somewhat decent peformance. I ordered the last of the components today so I hope to be building and measuring this later next week. You should be able to work out what THD you will get on the back of an envelope. The spare sides of envelopes comprise some of the hardware of my kitchen table simulator. I use scrap paper from my printer. Computer Power for the Simulator is a 1947 Model HO, ( Human Organic ), which was last tested in 1962 and gave a 135 reading for IQ, although the guys testing it said it was slow, and uncooperative to command programs. I find that easy to believe ;-) But the only time significant 2H cancellation occurs would be when you turn down the gain pot, and only one position where cancellations will be almost complete. Strangely best cancellation appears to be with the gain pot turned full up. Wait until you do a real amp..... Using constant current sources for all your triode loads would reduce the THD at 3V output by around 10dB at least, and you'd never have to worry about THD at all. 0.02% at a volt output is usually utterly inaudible. I was not particularly trying to avoid it - I was quite looking forward to a bit of tube sound. I did want to limit it as far as possible to 2H distortion which is why I avoided local and global NFB. I was expecting about 0.2% and that is what I get at the 2nd tube anode. I was surprised to find that by tweaking CF values I could reduce this value at the CF output - hence the question about distortion cancellation. What prompted me to tweak the CF values was that my initial CF design produced more distortion than the prior two stage combined. You'd have to use a very low value load to force the CF to produce enough THD to cancel that of the preceeding gain stage. See above. I will bet you a dozen schooners that just arrangeing the circuit to get maximal cancellations won't give you the open effortless warm detailed dynamic clear crisp hifi that well set up tubes will give. I am sure you are right. The main cauise of any THD is the gain tube after the pot. Now if B+ was +300V, and you had a 47k load, and Ea = +130V, then Ia would be 3.61 mA. Neglect the few volts across the cathode R with say 470uF bypass. Ra = approx 10k, µ =36, so gain = 36 x 47 / ( 47 + 10 ) = 30 approximately. Now if you were to use a CCS, the gain = µ = 36 and the THD would be about at least 1/3 of the value for the 47k, and should you wish, B+ could be +250V, Ea at 120V, and Ia = 5ma, and THD would fall even further, because with the high RL and higher Ia, the linearity would peak at more than 3.6mA. First stage B+ is 170V, Ea=86V and Ia=0.8mA and 2nd stage has B+=250V, Ea=82V and Ia=1.7mA at present. Anode load is 100K in both cases. If you have the anode curves for a 6AU6 in triode, the CCS load appear as a horizontal line through whatever value of idle current you choose, and the amount of variation between each Ra curve line for each value of grid bias diminishes to a minimum when the load line is a horizontal one. I can assure you the very best "tube sound" comes from triodes operating in pure *voltage* mode with NO anode current change that is easily measured, which is the case with a CCS using a single pnp transistor where the actual load is around 30Mohms, and regarded as a source of current which does not vary regardless of the variation in anode voltage. There will still be some THD even with a CCS. Sounds very interesting and I guess I could still use a 6AU6 for the CSS? You can calculate what this might be from measuring the spacings between the Ra lines. But usually, the Ra data lines cannot be taken as gospel and are an approximation of the actual curves one might get with a given tube sample. When they may have drawn up the curves 60 years ago, the gear they used may have had 5% errors, and usually the actual THD of a triode with CCS is better than what the curves might suggest. To establish just what goes on you should have a distortion meter with input impedance of at least 500k and capable of measuring 0.005% THD in any voltage between 0.5Vrms and 100Vrms. 0.005% of 0.5Vrms = 25uV, and so to see this on a CRO you need to have a clean test signal with THD = 0.001% max, and be able to remove the 1kHz signal from the signal being examined to below the THD level, and then have a bandpass filter from 1.5kHz to say 10kHz and have an amp to raise the THD by say 20 times to 500uV, or 0.5mV to be able to just see it on your CRO. I built my own oscillator, filters and amp to be able to measure THD this well. But if you asked me to analyse further just what spectral content was in the 0.005%, I would be unable to do it. Its safe to suggest that if the CRO shows the THD as a mainly simple sine wave of 2kHz, then the 3H might be say 10dB down, or be 0.0016%, rather low, and not a major worry, IMHO. Noise and hum will fight against you all the way to trying to get a decent measurement. One could have a tunable band pass filter with a Q = 50, and then the harmonics can be picked out one by one because the noise across such a tiny BW becomes less than the harmonic. I built such a filter, which has a dual gang pot for tuning and 3 opamps and a complex arrangement of NFB and PFB and is incomprehensible to understand. But it works, and cost me only a week to make it work. Using the right sort of sound card and PC and program also can give you what I get with primitive analog test gear I made BC, ( before I had a computer ). I now don't worry too much about the composition of the THD. Tube THD and the resulting IMD isn't ever a problem with a preamp if you are careful with triodes. Pentodes are also quite nice used as such, but need shunt NFB to reduce their high gain. And they have much more noise if used as input tubes for mics. The 6AU6 should be a fine triode for an input situation and compete with 1/2 a 6DJ8 for noise and gain. RDH seems to think so too. But you do need a reasonably high input signal for a microphone signal. With a phono amp, the HF are attenuated at about an approximate slope of 6dB/octave above 50Hz, and the phono signal has had its HF boosted, so noise can be very low, but for a mic the signal is flat, and unboosted, and to get low noise the input signal must be high. Agreed. Normal practice for tube mic pres seems to be to have a fairly high turns ratio (10:1 or more) transformer at the input which can provide 20dB or more of relatively low NF gain. Using microphones for recording isn't something I have ever done much and if I did i'd probably not use a tube at all but use a j-fet. These are far quieter than any triode. Most triodes have a hissy noise signal of maybe 2uV if you are lucky. DC on the heaters is imperative. Shielding may be needed. Microphony is avoided by careful tube choice. Yes, it is a fascinating design challenge. Ian |
#17
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell said:
This is where the cancellation appears to take place in the CF. Then there is something very badly wrong with your CF or your simulation. Why don't you post your circuit diagram, perhaps to ABSE? Easy done. Maybe you could show pictures of your graphs too. That would be instructive. cheers, Ian |
#18
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Phil Allison wrote:
"Ian Bell" ** Is there to be an input step-up transformer ?? There is 10:1 ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. Stage gain is about 30dB and transformer gain is 20dB - max gain 20+30+30=80dB - excessive even for a mic pre. Trouble is, for a nominal +4dBm output, a single 30dB stage and transformer will give an input sensitivity of just -46dBm which is barely adequate in many situations. Some more gain would be preferable. Changing the first stage to a pentode would supply extra gain but would be too noisy. Using local NFB on each triode to reduce the stage gain to 20dB would work. Ian |
#19
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Iveson wrote:
Ian Bell said: This is where the cancellation appears to take place in the CF. Then there is something very badly wrong with your CF or your simulation. Personally I strongly suspect the simulation. Why don't you post your circuit diagram, perhaps to ABSE? Easy done. Maybe you could show pictures of your graphs too. That would be instructive. cheers, Ian I assume ABSE is a binaries news group? if so my ISP does not provide access to binary groups. Ian |
#20
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Ian Bell" ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. Stage gain is about 30dB and transformer gain is 20dB - max gain 20+30+30=80dB - excessive even for a mic pre. Trouble is, for a nominal +4dBm output, a single 30dB stage and transformer will give an input sensitivity of just -46dBm which is barely adequate in many situations. ** Your first stage fixed gain of over 300 times is way too high. Input overload will be a constant problem - particularly with a condenser mic. An input pad will make things noisy again. ........ Phil |
#21
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Patrick Turneroid ****wit" "Ian Bell" ** Is there to be an input step-up transformer ?? There is 10:1 ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. If the mic signal = 0.5mV, then gain of 10,000 gives 5Vrms. If the pot gain control is to be used at the -20dB central position, then Vo = 0.5Vrms. Madness? ** For serious recording work, mic gain of 1000 times is not usable as it results in excessive background noise - consisting audible hiss from the mic and pre -amp PLUS amplified noise from the environment. Having 1000 times gain at only half knob setting is UTTERLY INSANE !! The OP has not built his fantasy tube pre-amp yet - when an if he does, he will soon see it is not a game for mugs like him. ....... Phil |
#22
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
This is where the cancellation appears to take place in the CF. I don't think any such cancelation could occur. If you have a direct coupled CF with the 3rd 6AU6, then the load between cathode and 0V for 4mA for Ia will be 30k. In fact with something else connected to the CF, the load could end up being 25k, and for 3V output, perhaps Vgk = 3V/gain of 20 = 0.15V. In the present design the CF is AC coupled to the preceding triode stage. The CF cathode connects to ground via a 1K and 3.3K in series. The junction of these two goes to g1 via 330K. The 1K is bypassed with 47uF. The cathode sits at about 21V and the anode current is about 5mA and g1 is about -5V wrt the cathode. The CF load is way to low. CF loads should never be lower than what you use for an anode load. The low CF load forces it to distort. loop gain becomes lower as RL for the CF load is reduced, and the local CF NFB also becomes lower, so less correction of the THD occurs. CF open loop gain = cathode output signal / Vgk signal. CF closed loop gain = (cathode output signal + Vgk) / Vgk Patrick Turner. |
#23
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Iveson wrote: Ian Bell said: This is where the cancellation appears to take place in the CF. Then there is something very badly wrong with your CF or your simulation. Why don't you post your circuit diagram, perhaps to ABSE? Easy done. Maybe you could show pictures of your graphs too. That would be instructive. cheers, Ian He already said how he has a total RL of the CF = 4.3k. Hence the high THD of the CF. Patrick Turner. |
#24
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote: Phil Allison wrote: "Ian Bell" ** Is there to be an input step-up transformer ?? There is 10:1 ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. Stage gain is about 30dB and transformer gain is 20dB - max gain 20+30+30=80dB - excessive even for a mic pre. Trouble is, for a nominal +4dBm output, a single 30dB stage and transformer will give an input sensitivity of just -46dBm which is barely adequate in many situations. Some more gain would be preferable. Changing the first stage to a pentode would supply extra gain but would be too noisy. Using local NFB on each triode to reduce the stage gain to 20dB would work. Ian He has a gain pot in the tube line up. If for normal use its set at the 12oclock position, its giving -20dB, so total gain in effect is 60dB, not 80dB, so a 0.5mV mic signal is raised to 0.5V, which seems plausible. Patrick Turner. |
#25
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote: Ian Iveson wrote: Ian Bell said: This is where the cancellation appears to take place in the CF. Then there is something very badly wrong with your CF or your simulation. Personally I strongly suspect the simulation. Why don't you post your circuit diagram, perhaps to ABSE? Easy done. Maybe you could show pictures of your graphs too. That would be instructive. cheers, Ian I assume ABSE is a binaries news group? if so my ISP does not provide access to binary groups. Most binaries usernet groups convey a vast huge amount of pornography to the sex staved millions of men who demand it. All other usernet traffic is a small amount of data by comparison. data costs money to transfer. Find yourself an ISP who gives you access to the Internet and includes access to all binaries. I had many rows with ****ing ISPs who promised good access to NGs included in their internet access price but who failed to give it. I had to shop around about 6 times before I could get abse reliably, and even then its never instant; image posts take maybe 2 days to be seen after folks posts them or m,aybe I miss out, becays ebinaries, or images are only held in servers for 48 hours, and the delays in refresh times means that when my ISP source updates the list of posts, the binaries posts have expired from upstream. The amount of traffic also has an effect. less flow = less updates = expired articles. You never get problems with alt.binaries.pictures.erotica.blondes There are hundreds of posts each day. But abse and some others about radio and phonogrpahs also don't have much content flow and don't get through in the system. Patrick Turner. Ian |
#26
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Phil Allison wrote: "Patrick Turneroid ****wit" "Ian Bell" ** Is there to be an input step-up transformer ?? There is 10:1 ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. If the mic signal = 0.5mV, then gain of 10,000 gives 5Vrms. If the pot gain control is to be used at the -20dB central position, then Vo = 0.5Vrms. Madness? ** For serious recording work, mic gain of 1000 times is not usable as it results in excessive background noise - consisting audible hiss from the mic and pre -amp PLUS amplified noise from the environment. Having 1000 times gain at only half knob setting is UTTERLY INSANE !! The OP has not built his fantasy tube pre-amp yet - when an if he does, he will soon see it is not a game for mugs like him. I mentioned he would have a mic signal of only 0.5mV. He said he wanted to have a 1:10 tranny, and first stage 6AU6 *triode* gain = 25 approx. So 0.5mV becomes 5mV, then is amplified to 125mV, and then reduced to 12.5mV at the output of the gain pot in the 12 o'clock position. the next stage might have gain = 30, so he gets 375mV output. The noise of the amp is determined by its input noise of perhaps 2uV, some 68dB below the 5mV signal from the mic tranny. Don't worry, he will find out if whatever he builds gives problems because he always checks all his work and measures and investgates the viability, and if there are any problems whatsoever, and takes all appropriate action to make sure none of the bothers you mention could trouble his recording experiences. Don't worry. Be happy. Patrick Turner. ...... Phil |
#27
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
flipper wrote: On Sat, 16 Jun 2007 21:13:40 +0100, Ian Bell wrote: Patrick Turner wrote: Ian Bell wrote: trim The 6AU6 should be a fine triode for an input situation and compete with 1/2 a 6DJ8 for noise and gain. RDH seems to think so too. I'm curious. With the 6DJ8 having 3 to 4 times the gm what's the advantage to a trioded 6AU6 for the first stage rather than the 6DJ8? Cost? I have accumulated about 40 6AU6 in my junk boxes. I didn't pay for any of them, and don't know how they got there. When i turn 150, I will be able to draw on the stocks of tubes I still will have. I will be able to pretend I can hear the music, for I will have become quite deaf. Patrick Turner. |
#28
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Patrick Turner
Then there is something very badly wrong with your CF or your simulation. Why don't you post your circuit diagram, perhaps to ABSE? Easy done. Maybe you could show pictures of your graphs too. That would be instructive. cheers, Ian He already said how he has a total RL of the CF = 4.3k. Hence the high THD of the CF. And the lost opportunity for direct coupling. The problem was unlikely to be spice, although I find measuring distortion via fourier a bit hit and miss. I should make a distortion meter I suppose. I thought you might have been more forthcoming wrt 2H cancellation. If valves 1 and 2 had the same load and operating point then 2H would cancel if the attenuation between the two resulted in no overall gain for the first stage, so the second would produce the same amount, but inverted. If the valves are at different operating points, then a minimum 2H would be somewhere else on the volume setting. At high volume settings, the 2H from the valve 2 would predominate. Assuming that to be the case, it is interesting to note that the distorting CF, although it is a non-inverting stage, reduces the total 2H at high volume settings. Anyway, Ian might try the CF as it is, with a clean signal, and measure the ensuing output, for a range of amplitudes and loads. We should have nipped this CF fetishism in the bud. It'll be the death of us. I hadn't really looked at a sharp-cutoff pentode before now. Do they do things like that but bigger? Why don't I have a model of one? I fancy PP transformer coupled with distributed load and cross-coupled screens. cheers, Ian |
#29
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Patrick Turner" ** For serious recording work, mic gain of 1000 times is not usable as it results in excessive background noise - consisting audible hiss from the mic and pre -amp PLUS amplified noise from the environment. Having 1000 times gain at only half knob setting is UTTERLY INSANE !! The OP has not built his fantasy tube pre-amp yet - when an if he does, he will soon see it is not a game for mugs like him. The noise of the amp is determined by its input noise of perhaps 2uV, some 68dB below the 5mV signal from the mic tranny. ** 68 dB is absolutely NOT an acceptable s/n ratio for a professional mic preamp operating in the middle of it's gain range. The figure needs to be circa 90 dB - as is routinely obtained with standard commercial designs. Plus you have omitted the self noise of the mic - which will degrade that figure another 3dB to a horrible 65dB. Plus you omitted the output stage noise, which will reduce the ratio further by couple of dB at that gain setting. A joke. ...... Phil |
#30
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Phil Allison wrote:
"Ian Bell" ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. Stage gain is about 30dB and transformer gain is 20dB - max gain 20+30+30=80dB - excessive even for a mic pre. Trouble is, for a nominal +4dBm output, a single 30dB stage and transformer will give an input sensitivity of just -46dBm which is barely adequate in many situations. ** Your first stage fixed gain of over 300 times is way too high. Input overload will be a constant problem - particularly with a condenser mic. An input pad will make things noisy again. ....... Phil Indeed. That's why I plan to use an input transformer designed for use in a Helios console. It has a tap on the secondary that gives a 1:1 ratio instead of 1:10. A switch to select between the two acts like a 20dB pad. Ian |
#31
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Patrick Turner wrote:
This is where the cancellation appears to take place in the CF. I don't think any such cancelation could occur. If you have a direct coupled CF with the 3rd 6AU6, then the load between cathode and 0V for 4mA for Ia will be 30k. In fact with something else connected to the CF, the load could end up being 25k, and for 3V output, perhaps Vgk = 3V/gain of 20 = 0.15V. In the present design the CF is AC coupled to the preceding triode stage. The CF cathode connects to ground via a 1K and 3.3K in series. The junction of these two goes to g1 via 330K. The 1K is bypassed with 47uF. The cathode sits at about 21V and the anode current is about 5mA and g1 is about -5V wrt the cathode. The CF load is way to low. CF loads should never be lower than what you use for an anode load. The low CF load forces it to distort. loop gain becomes lower as RL for the CF load is reduced, and the local CF NFB also becomes lower, so less correction of the THD occurs. CF open loop gain = cathode output signal / Vgk signal. CF closed loop gain = (cathode output signal + Vgk) / Vgk Patrick Turner. Interesting. I originally started with 10K but got a lot of distortion. As i lowered it distortion lowered too. sounds like a simulation error. I wish these parts would hurry up and arrive so I can start building. Ian |
#32
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Iveson wrote:
Patrick Turner Then there is something very badly wrong with your CF or your simulation. Why don't you post your circuit diagram, perhaps to ABSE? Easy done. Maybe you could show pictures of your graphs too. That would be instructive. cheers, Ian He already said how he has a total RL of the CF = 4.3k. Hence the high THD of the CF. And the lost opportunity for direct coupling. I avoided this initially because the heater cathode volts on this tube must not exceed 100V which limits Va on the tube feeding it. Also I am concerned that at switch on, if HT is not delayed, the heater cathode voltage could be near B+ untill the tubes start to conduct. The problem was unlikely to be spice, although I find measuring distortion via fourier a bit hit and miss. If you are using LTCspice like I am you need to ensure data compression is turned OFF (I never understood why they have it in the first place). You can do this with the following directive: ..option plotwinsize=0 You can get a distortion measurement directly using the spice FOUR command e.g. ..FOUR 1000 V(out) where V(out) is the node at which you want to make the measurement and 1000 is the frequency. You need to have a sine source of this frequency at the circuit input and do a transient response simulation for the fourier command to have the data to work on. I should make a distortion meter I suppose. They come up occasionally on eBay. I have a nice HP unit. Ian |
#33
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
flipper wrote:
On Sat, 16 Jun 2007 21:13:40 +0100, Ian Bell wrote: Patrick Turner wrote: Ian Bell wrote: trim The 6AU6 should be a fine triode for an input situation and compete with 1/2 a 6DJ8 for noise and gain. RDH seems to think so too. I'm curious. With the 6DJ8 having 3 to 4 times the gm what's the advantage to a trioded 6AU6 for the first stage rather than the 6DJ8? Nothing other than I happen to have some ;-) Ian |
#34
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Ian Bell" ** Your first stage fixed gain of over 300 times is way too high. Input overload will be a constant problem - particularly with a condenser mic. An input pad will make things noisy again. Indeed. That's why I plan to use an input transformer designed for use in a Helios console. It has a tap on the secondary that gives a 1:1 ratio instead of 1:10. A switch to select between the two acts like a 20dB pad. ** Then you EIN goes back to an horrendous 3 uV. Time you described fully what you are planning - instead of reacting to each criticism with another knee jerk design change. Cos what you have described so far is a noise ridden, distorting, utter abortion for professional recording. ........ Phil |
#35
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Phil Allison wrote: "Patrick Turner" ** For serious recording work, mic gain of 1000 times is not usable as it results in excessive background noise - consisting audible hiss from the mic and pre -amp PLUS amplified noise from the environment. Having 1000 times gain at only half knob setting is UTTERLY INSANE !! The OP has not built his fantasy tube pre-amp yet - when an if he does, he will soon see it is not a game for mugs like him. The noise of the amp is determined by its input noise of perhaps 2uV, some 68dB below the 5mV signal from the mic tranny. ** 68 dB is absolutely NOT an acceptable s/n ratio for a professional mic preamp operating in the middle of it's gain range. The figure needs to be circa 90 dB - as is routinely obtained with standard commercial designs. Plus you have omitted the self noise of the mic - which will degrade that figure another 3dB to a horrible 65dB. Plus you omitted the output stage noise, which will reduce the ratio further by couple of dB at that gain setting. A joke. Something has to give. If the attempt at recording is serious, and a 90bB SNR is wanted, then he could throw away 20dB of amp gain but increase the mic signal by 20 dB. I can only advise on the figures of noise he might get with the gear proposed and voltages mentioned. If his recordings are noisy then he will find out. He may be quite happy with a 65 db SNR. I have never examined a studio mic's impedance or output voltage characteristics or noise production. Iain should know, or even Arny, both claim experience, and you might know, but are too lazy to tell us all we might need to know, or where we may find a reliable source of the info. You'd rather tell us all we are autistic etc, rather than contribute constructively. I have found that many cds and vinyls have noise well above the amp I use. probably these recordings have a worse SNR than 65 dB. I don't have the time to investigate all the facts and skills required for recording seriously. My experience is limited to amateur home use of a cassette deck with a pair of Akai mics I bought 30 years ago for some folk music. Patrick Turner. ..... Phil |
#36
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Ian Bell" wrote in message ... Ian Iveson wrote: Ian Bell said: This is where the cancellation appears to take place in the CF. Then there is something very badly wrong with your CF or your simulation. Personally I strongly suspect the simulation. Why don't you post your circuit diagram, perhaps to ABSE? Easy done. Maybe you could show pictures of your graphs too. That would be instructive. cheers, Ian I assume ABSE is a binaries news group? if so my ISP does not provide access to binary groups. Ian. I can host them for you if required. Iain |
#37
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Ian Bell" wrote in message ... Phil Allison wrote: "Ian Bell" ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. Stage gain is about 30dB and transformer gain is 20dB - max gain 20+30+30=80dB - excessive even for a mic pre. Trouble is, for a nominal +4dBm output, a single 30dB stage and transformer will give an input sensitivity of just -46dBm which is barely adequate in many situations. ** Your first stage fixed gain of over 300 times is way too high. Input overload will be a constant problem - particularly with a condenser mic. An input pad will make things noisy again. ....... Phil Indeed. That's why I plan to use an input transformer designed for use in a Helios console. It has a tap on the secondary that gives a 1:1 ratio instead of 1:10. A switch to select between the two acts like a 20dB pad. Dick S knew a trick or two:-) One saw this on the Schlumberger desks, and also those built under licence for Scandinavian broadcast companies by Kajaani Electronics. Iain |
#38
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Patrick Turner" wrote in message ... If the attempt at recording is serious, and a 90bB SNR is wanted, then he could throw away 20dB of amp gain but increase the mic signal by 20 dB. I can only advise on the figures of noise he might get with the gear proposed and voltages mentioned. If his recordings are noisy then he will find out. He may be quite happy with a 65 db SNR. I have never examined a studio mic's impedance or output voltage characteristics or noise production. Iain should know, or even Arny, both claim experience, and you might know, but are too lazy to tell us all we might need to know, or where we may find a reliable source of the info. You'd rather tell us all we are autistic etc, rather than contribute constructively. Modern mic preamplifiers are probably nearer SNR 90dB which Phil mentions. I remember tube mics, Neumann M47, M49 and M50 with tube input stages on the console that were probably much closer to the fig of 65dB. Rarely was tube noise a problem. Interestingly, many of those mics that were converted to FET in the 70s are now being converted back to tubes. I have found that many cds and vinyls have noise well above the amp I use. probably these recordings have a worse SNR than 65 dB. Yes that's common. I have many CDs on which one can clearly hear the noise floor, followed by a digital "fade to black" Iain |
#39
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
"Phil Allison" wrote in message ... "Ian Bell" ** Then why the hell have *2* triode gain stages with well over 1000 times gain ?? Makes your total gain OVER 10,000 TIMES !! Madness. Stage gain is about 30dB and transformer gain is 20dB - max gain 20+30+30=80dB - excessive even for a mic pre. Trouble is, for a nominal +4dBm output, a single 30dB stage and transformer will give an input sensitivity of just -46dBm which is barely adequate in many situations. ** Your first stage fixed gain of over 300 times is way too high. Input overload will be a constant problem - particularly with a condenser mic. An input pad will make things noisy again. Much depends on the recording. On jazz sessions, studio assistants switch in the pads on every mic except woodwinds, bass and acoustic guitar even without being asked:-) Iain |
#40
Posted to rec.audio.tubes
|
|||
|
|||
Canceling distortion
Ian Bell wrote: I plan to use an input transformer designed for use in a Helios console. You have one lying around ? It has a tap on the secondary that gives a 1:1 ratio instead of 1:10. A switch to select between the two acts like a 20dB pad. Oh dear. Helios didn't make valve consoles. May I suggest a Lundahl transformer ? If you have to have a transformer, you might as well use a good one. They only do 1:7 http://lundahl.se/pdfs/datash/1576_77.pdf or 1:8 http://lundahl.se/pdfs/datash/7903.pdf in a suitable design though. Yes, there are other higher turns ratios but they're not designed for 200 ohm sources and / or today's high microhone levels. You don't want a transformer designed for 50 or 600 ohms. Note that these will present a source Z to the tube of ~ 10-13 kohms. Graham |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Seinnheiser PXC 250 Question on Noise canceling headphones. | Audio Opinions | |||
Sennheiser Noise-Canceling Headphones | High End Audio | |||
Best CD (whitenoise) to use with Bose noise canceling headphones | Tech | |||
noise-canceling standalone units? | Tech |