Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Aiwa Cassette Deck Belt Repair?
Does anyone know how the drive belts are arranged
on an Aiwa AD-F800 cassette deck? There are two belts, and seemingly three things for them to wrap around: --a large flywheel that drives the take-up spindle (and also engages the mechanism that lifts the heads and pinch rollers into place for playback), --a smaller flywheel that drives the feed spindle, --and the drive shaft of a small motor at the top rear of the transport assembly. Both belts have slipped off, and I can't figure out how they go back. Thanks in advance. --David Perris |
#2
|
|||
|
|||
David,
First let me tell you that I don't remember this model, so my reply is not specific to your machine. If the belt have slipped off, then they are also likely to have stretched out in size and need replacement. The large, flat belt is likely to go around the cast metal flywheel to the capstan, and the wide section of the motor pulley. The smaller square belt from the small section of the motor pulley to the reel drive. Again, belts almost NEVER fall off unless they are too large, or someone has forced something in a jammed mechanism. For good belts to fall off even in transit, the machine would be damaged beyond repair. Regards, Tim Schwartz Bristol Electronics David Perris wrote: Does anyone know how the drive belts are arranged on an Aiwa AD-F800 cassette deck? There are two belts, and seemingly three things for them to wrap around: --a large flywheel that drives the take-up spindle (and also engages the mechanism that lifts the heads and pinch rollers into place for playback), --a smaller flywheel that drives the feed spindle, --and the drive shaft of a small motor at the top rear of the transport assembly. Both belts have slipped off, and I can't figure out how they go back. Thanks in advance. --David Perris |
#4
|
|||
|
|||
Is it an auto-reverse deck? If it's single direction, with 2 flywheels, then
one flat belt goes from one flywheel to the motor pulley, the other flat belt loops around the outer circumference of both flywheels. If it's an auto-reverse model, then normally one belt loops from the pulley, over the top of one flywheel, and under the second, coming back around the top over to the motor pulley. Mark Z. -- Please reply only to Group. I regret this is necessary. Viruses and spam have rendered my regular e-mail address useless. "David Perris" wrote in message ... Tim: Thanks so much for the reply. The machine was sitting unused for a long time, so I suspect the belts degraded. Actually, the two belts are both flat ones, and the two flywheels are attached to the take-up and feed spindles, rather than to the capstan-- I think there's a separate motor for that. The big flywheel has some kind of clutch mechanism that engages just long enough to lift the heads into place when you press Play, then kicks itself back into driving the takeup reel. It's kind of hard to figure out where the belts go, and they fell off before I could make a sketch. I'll take another look inside. Thanks again for your help. --David in article , Tim Schwartz at wrote on 8/14/04 8:37 AM: David, First let me tell you that I don't remember this model, so my reply is not specific to your machine. If the belt have slipped off, then they are also likely to have stretched out in size and need replacement. The large, flat belt is likely to go around the cast metal flywheel to the capstan, and the wide section of the motor pulley. The smaller square belt from the small section of the motor pulley to the reel drive. Again, belts almost NEVER fall off unless they are too large, or someone has forced something in a jammed mechanism. For good belts to fall off even in transit, the machine would be damaged beyond repair. Regards, Tim Schwartz Bristol Electronics David Perris wrote: Does anyone know how the drive belts are arranged on an Aiwa AD-F800 cassette deck? There are two belts, and seemingly three things for them to wrap around: --a large flywheel that drives the take-up spindle (and also engages the mechanism that lifts the heads and pinch rollers into place for playback), --a smaller flywheel that drives the feed spindle, --and the drive shaft of a small motor at the top rear of the transport assembly. Both belts have slipped off, and I can't figure out how they go back. Thanks in advance. --David Perris |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Please help me with cassette deck to amp connections | Tech | |||
Aiwa cassette deck problem | Tech | |||
FA: JVC Stereo Dual Cassette Deck - TD W218 | Marketplace | |||
Sherwood Dual Auto Reverse Cassette Deck, $79 | Marketplace |