Home |
Search |
Today's Posts |
#1
|
|||
|
|||
ROTEL RA-1062 enters protection mode at half volume control position?
Hello everybody,
Four months ago I purchased a Rotel RA-1062 and a pair of Bowers-Wilkins 604-S3 speakers. To start with something that may be a problem, the amplifier is rated 2x60, while the speakers are 200 each. The speakers are single-wired with Monster cables. Okay, as sources, these were not upgraded up to now - I have a Technics AZ-7 casette player (a very good-sounding machine, film-head technology etc) and a non-fantastic-at-all Technics CD-changer, but which worked with no problem up to now. The integrated amplifier barely has 30 hours on it. For two weeks now (having moved my equip in a basement, which is cold and dry btw) I started listening at half-volume control position. Well, on certain (but enough) CD-s the amplifier appears to enter protection for 3-10 seconds that is the sound completely stops, then resumes for a few seconds, then stops again and so on until I reduce the volume. On certain tracks I can reproduce this on the volume control turned to hour 11 for example, so significantly less than half volume. Now, I tried to do some investivation on my own. Overheating? Well, it sits directly on the cold floor, nothing on top of it. I do not have a power conditioner, just regular grounded outlet. Does the CD skip (because at the first moment this is what I thought of)? I've changed the source to tape, the same interruptions appeared (listening to some heavily orchestrated music like "No Doubt" for example). Now the tricky part. I tried running the CD changer through the AZ-7 tape player, through monitoring, and I remarked the CD-s on which the Rotel enters protection apparently are recorded with a higher signal level (the signal level indicators on the tape player's monitoring system stay on the red area 80% of the time). Manually decreasing the signal on the tape monitor (which decreases the signal level that's fed on to the amplifier appeared to cure the problem! no more interruptions! I could go near the maximum with the volume control with sound levels apparently higher than those obtained before when the volume control was at half position but the signal was not decreased by the tape monitor. What can that be? How am suppose to cure it? Could it be something with the preamplifier section of the integrated, which does not level (should that be done???) the signal it is fed with? Or with the power amplification section? Do you think switching to a Rotel pre+power (RC-1070 + RB-1070) will cure this? Of course, I could also replace the old Technics CD-changer with the Rotel CD-player (1072), but I don't feel like spending when I'm not certain it will work, plus it will continue to fail while fed with signal from the AZ-7 casette player. Well, I hope somebody here can enlighten me. Thank you! Michael. |
#2
|
|||
|
|||
Reducing the signal level or dynamic range of the CD is the same as
turning down the volume level on the amp. The amp can't handle the loudspeakers load and was a poor choice. You can replace the speakers with something more efficient and with a more stable, higher impedance or get another, more capable amplifier. Although I am not a fan of the B&W sound, the speakers are not the weakest link there. -Bill www.uptownaudio.com Roanoke VA (540) 343-1250 "Michael Kiss" wrote in message ... Hello everybody, Four months ago I purchased a Rotel RA-1062 and a pair of Bowers-Wilkins 604-S3 speakers. To start with something that may be a problem, the amplifier is rated 2x60, while the speakers are 200 each. The speakers are single-wired with Monster cables. Okay, as sources, these were not upgraded up to now - I have a Technics AZ-7 casette player (a very good-sounding machine, film-head technology etc) and a non-fantastic-at-all Technics CD-changer, but which worked with no problem up to now. The integrated amplifier barely has 30 hours on it. For two weeks now (having moved my equip in a basement, which is cold and dry btw) I started listening at half-volume control position. Well, on certain (but enough) CD-s the amplifier appears to enter protection for 3-10 seconds that is the sound completely stops, then resumes for a few seconds, then stops again and so on until I reduce the volume. On certain tracks I can reproduce this on the volume control turned to hour 11 for example, so significantly less than half volume. Now, I tried to do some investivation on my own. Overheating? Well, it sits directly on the cold floor, nothing on top of it. I do not have a power conditioner, just regular grounded outlet. Does the CD skip (because at the first moment this is what I thought of)? I've changed the source to tape, the same interruptions appeared (listening to some heavily orchestrated music like "No Doubt" for example). Now the tricky part. I tried running the CD changer through the AZ-7 tape player, through monitoring, and I remarked the CD-s on which the Rotel enters protection apparently are recorded with a higher signal level (the signal level indicators on the tape player's monitoring system stay on the red area 80% of the time). Manually decreasing the signal on the tape monitor (which decreases the signal level that's fed on to the amplifier appeared to cure the problem! no more interruptions! I could go near the maximum with the volume control with sound levels apparently higher than those obtained before when the volume control was at half position but the signal was not decreased by the tape monitor. What can that be? How am suppose to cure it? Could it be something with the preamplifier section of the integrated, which does not level (should that be done???) the signal it is fed with? Or with the power amplification section? Do you think switching to a Rotel pre+power (RC-1070 + RB-1070) will cure this? Of course, I could also replace the old Technics CD-changer with the Rotel CD-player (1072), but I don't feel like spending when I'm not certain it will work, plus it will continue to fail while fed with signal from the AZ-7 casette player. Well, I hope somebody here can enlighten me. Thank you! Michael. |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Volume Control ... | Tech | |||
Volume Control ... | General | |||
Alpine MRV-F540 - Protection Mode ? | Car Audio | |||
volume control & system possessed...very weird! | Tech | |||
Passive Volume Control (Passive Preamp) Info | High End Audio |