[Alex Pogossov]

"John L Stewart" wrote in message
...

The original of this article was published in AudioXpress magazine,
sometime in 2001. I had to remove the parts list as the post was too
long. Try that later.


Amplifier Burst Testing John L Stewart

When your amplifier is driven hard it's power supply in most cases will
sag. There are few exceptions. Even a Class A amplifier pulls a little
more current at full output than it does at no signal. As you progress
into Class AB & farther, the output stage will need more current & your
power supply
voltage will drop even further. Because of cost it is customary that
only instrumentation amplifiers have a regulated power supply.

Yet, one of the most commonly used checks tests amplifiers at full
single tone CW (Continuous Wave) output, usually one KHz. That's
unrealistic since no sane person would last long listening in that kind
of environment. If your ears didn't fail then your loudspeaker probably
will. If your program material has a 60 to 80 db (or whatever) dynamic
range then what can you do to get some measure of the real output
(headroom) available? What is the output capability of the amp for a
short burst? That's a realistic test since that is how most of your
program material is available.

There are several ways in which a tone burst can be produced so that
your amp can be tested in this mode. This is one of them. This simple
gate circuit allows you to apply tone bursts to the amp in test. The
signal originates in your existing audio generator. The gate can be set
to allow a few cycles of the test tone through & then blocks the signal.
Repetition rate of the tone bursts is set at about 14Hz but could be
varied. Now power output measurements can be made while full power
supply voltage is applied to the amplifier. You will need an
oscilloscope on which to observe & measure the test results.

The test works with any amp whether it be solid or vacuum state. It is
possible to build two versions. The simpler depends on your scope having
a sweep gate connection, usually found on the rear panel. If that is
not available a three transistor gate driver with synchronizing of the
gate to the audio generator source can be added. Nothing is wasted.

All can be done for less then $100.00. I built mine in a Hammond 5 x
13.5 x 2 chassis so that it fits right under my scope, where it can
stay. Many of the parts came straight out of my junk box!!!

THE GATE

The gate itself is nothing more than a pair of back to back connected
Hammond interstage transformers, switched by a pair of diodes. Refer to
Figure One, The Gate. One of the connectors on the rear of my scope
is a positive pulse in time with the horizontal sweep. The sweep gate
pulse drives the diodes D1 & D2 into conduction & the test tone passes
through to the output terminals. Diodes in my final version are very old
1N478's, mostly because I had some. They are Germanium, so I thought
they might
work better because of the low forward drop. I did try a variety of
other diodes as well. The silicon power diode series 1N400X works almost
as well. I inserted a three volt reverse bias (two "AA" cells) into that
lead so that the tone can't leak thru while the sweep gate is absent.

The DPDT switch S3 allows either continuous or burst signal mode to be
selected. As shown it is in the burst position. The switch section S1c
is part of the on-off switch, the rest of which is appears in the Gate
Driver schematic. The 4PDT switch S2 allows the test set to be
completely bypassed.

Because the circuit is working with a switched signal, some ringing
occurs in the transformers. This is for the most part damped out by the
network formed by R13, R14 & C6.

If your scope has a negative sweep gate than you could reverse the
diodes & the three volt battery.

GATE DRIVER

If your scope doesn't have a sweep gate or you would like a more
comprehensive piece of test equipment, you can drive the gate in a
number of different ways. Here is how I did it, mainly because I had
these
parts in my stockpile. Refer to Figure Two, the Gate Driver.

The gating pulse is provided by a one-shot multivibrator consisting of a
pair of 2N3053 NPN transistors. However the circuit is not critical &
any common NPN transistor could probably be used here. The multivibrator
in turn is triggered by a 2N1671 unijuction transistor. Unijunctions
were at one time
fairly common & I found them to be quite useful. However, they seemed to
have for the most part disappeared from the market.

The duration of the gate is determined by the setting of P1, the 50K
pot. With P1 set to minimum, the duration is long enough that about
three cycles of a one KHz test tone get thru. The gate signal will
probably not be synchronized with the audio source, so I have included a
connection through C3 & R7 which will help to stabilize the scope
display. As well, you can trigger your scope with the signal available
from the collector of Q2 & identified on the schematic as the Gate
Driver Output. I used a red binding post in order to differentiate from
the other front panel connections.
An example of the output burst is shown in Figure 3.

THE UNIJUNCTION

For those who are interested, a unijunction transistor is just that.
Only one junction, not two as in a regular bipolar. The base is a bar or
intrinsic material with connections at each end labeled B1 & B2 (Base
connections one & two). Ordinarily the base has a resistance of a few
Kohms between it's ends, so that little current can flow. The emitter
junction is placed part way in from one end of the bar, usually closer
to connection B2.

When the bar is supplied with a voltage source, a potential gradient
will result along it's length. In this case nine volts has been used.
Not much happens until the 1000 nF capacitor C1 charges up to a voltage
a bit greater than that which results on the bar where the emitter is
attached. As soon as the emitter-base junction is forward biased current
flows & discharges C1 into the base of Q2. That way the one-shot MV is
triggered & a gate pulse occurs. The CR time constant I used results in
about 14 pulses per second.

There are several references to the Unijunction on the web.
Refer to http://www.americanmicrosemi.com/tut...nijunction.htm
for a very good tutorial page & parts source if you decide to use a
unijunction in this project.

TEST SETUP & MEASURMENT

The hookup to test your amplifier is very straight forward. The test
tone from your audio generator is set to about one KHz and is not
critical. The test set is connected between your tone generator & the
amplifier you would like to test. Refer to the diagram showing the test
setup.

Output from the amplifier goes to the vertical input of your scope. With
the test set switched to the ON position there are a number of
possiblities. First of all, with switch S2 set to BYPASS you can route
your test tone straight through to the amplifier. Alternatively, you
could set switch S2 to TEST &
that way allow a few cycles of the test tone to pass. By varying the
position of pot P1 you will be able to pass more or fewer cycles of the
test tone.

I wanted to be able to make valid comparisons of amplifier performance
both with & without the test tone gated. Because the test set has a bit
of attenuation, I have included switch S3 which can set these
conditions. You will notice the attenuation if you were to look at the
output of the gate when the BYPASS mode is compared to the CONTINUOUS
mode.

The gate introduces about 2% distortion into the signal, but for the
intended application this is irrelevant. I included the BYPASS mode so
that you could leave the test set connected to the rest of your setup,
without having to worry about the gate's residual distortion &
attenuation.

Measurements of the signal amplitude are made with your scope, much like
you would normally do. What you are looking for is maximum signal output
from the amplifier at the clipping point, comparing the BURST &
CONTINUOUS modes (S3).

The table shows some results I measured which are fairly typical of
amplifiers, especially those running Class AB & have a power supply with
a capacitor input filter. This particular amp is push-pull 6V6GT's
running in Class AB2. A 6BQ7 drives the output grids into conduction.
The power supply is a small Hammond device rectified by SS diodes & into
a capacitor.
The test results are quite an eye opener that would not be obvious by
other test methods.

When tested by the normal CW method the scope trace had a maximum
amplitude of 17.5 volts at clipping. That translates to 12.4 vrms. The
load resistor used measured 7.85 ohms cold, so the output was 19.5
watts. When tested using the gated tone burst the maximum amplitude
measured at clipping on the scope was 20.2 volts. That translates to
about 26 watts!! Another advantage of burst testing is that your load
resistor doesn't change value due to heating while in the burst mode.

CONSTRUCTION

I built my burst tester into a small aluminum Hammond chassis which
easily fits under my scope. So that the front face would be tilted up I
installed a pair of 8-32x 1.25" machine screws with locking nuts in the
bottom plate. These are placed about 1.5" to one side of the long
dimension of the bottom plate center line with their heads facing down.
You may choose some other method to improve access.

The pair of double "A" cells (B3) are enclosed in a Radio Shack holder.
I used two sided sticky tape to mount the assembly to the inside of the
chasis. If you use alkaline cells at this point they will probably last
for at least five years, their normal shelf life, since the current
requirement is minimal. The two 9 volt batteries are simply held in by a
short length of #14 solid copper wire with the insulation still
attached. The wire is secured to the chassis with 6-32 screws. Again, if
you use alkaline batteries they should be good for 50 to 100 hours
operation in this circuit.

John L Stewart


+-------------------------------------------------------------------+
|Filename: Burst Gate_Driver_Test Setup.jpg |
|Download: http://www.audiobanter.com/attachment.php?attachmentid=344|
+-------------------------------------------------------------------+

The burst generator may be useful, but the design is arcane... like we are
not in 2013, but probably in 1963.

Attached is a simpler and much cheaper circuit. Cheaper than a CD and
possibly more convenient than fiddling with audio files editing on a PC.
http://www.valveradio.net/en/home/au...generator.html